MOB MO9771 Bedienungsanleitung
USER MANUAL
(2014/53/EU art. 10-8)
(a) Frequency Range; 2402-2480 MHz
(b) Maximum radio-frequency power; 100mW (EIRP)
(2014/53/EU art. 10-9 Simplified Declaration of Conformity)
Hereby, MOB, declares that item MOXXXX complies with the essential requirements and
other relevant conditions of directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address: www.morethangiftscatalogue.com
MOB, PO BOX 644, 6710 BP (NL).
PO: 41-95153
Made in China
MO9771
EN
Smart bracelet introduction and how to wear
Introduction of parts:
Wearing method
Wearing the bracelet just above the wrist is recommended;
Based on the size of the wrist, adjust the strap until the bracelet is
secure and comfortable and then close the buckle fastening;
The sensor should be close enough to the skin to avoid movement.
Charging the bracelet
To use, ensure the device is charged. If the power is too low it
cannot be used correctly, please connect the charger to charge the
device, then the bracelet will automatically turn on.
Charging method
Unplug the strap at both ends of the bracelet. Insert the USB side
of the bracelet into a USB charger or computer USB port.
Charging: Fully charged:
Start using the bracelet
Standby page: Shutdown page:
Switch device on/ off
1. In the device’s off state, long press the function key for more
than 4 seconds to turn the device on;
2. In the shutdown page, long press the function key for more than
4 seconds to enter the shutdown interface, and short press to
select OFF. The watch will then automatically shut down.
Bracelet operation
1. To turn on device; short press the function key to start.
2. Default clock page; touch the short press function key to view
the different pages/ functions.
3. When switching to the heart rate and blood pressure interface,
the test will start automatically. The test ends about 40 seconds
or so after selection (if this device supports that function).
Install the bracelet APP on the phone and update the firm
wear on the device to the latest version.
Scan the QR code below or search “Yoho Sports”to download
the APP.
System Requirements: Android 5.1 and above; iOS 8.0 and
above; supports Bluetooth 4.0.
Device connection:
For the first time you use the device you need to connect to the
APP for calibration. After connection is successful, the bracelet will
automatically synchronize the time, otherwise the pedometer and
sleep data is not accurate.
Special Note:
When connecting the device, please go through the app to pair
with Bluetooth, not through the setting in your phone.
1. After the pairing is successful, the APP will be automatically
searched and connected.
2. Android phones should ensure that you have all permissions,
such as running apps and reading contact information, during
installation or in your phone's system settings.
Personal information
Please set personal information after entering the APP;
Personal settings; you can set the gender - age - height - weight.
You can also set your daily exercise, sleep goals and monitor daily
completion.
Please set reminder time, you can also turn off this feature in the
message reminder.
Message notification
Incoming call: In the connected state, if the incoming call
reminder function is enabled, the device vibrates when calling, and
the name or number of the incoming call is displayed (Need to give
APP read address book permission).
SMS notification: In the connected state, if the SMS reminder
function is enabled, the bracelet will give reminder of message
received.
Other reminder: In the connected state, if you turn on this feature,
then there are WeChat, QQ and other news, the bracelet will
vibrate. (Need to give APP access to system notifications).
Vibrating reminder: Turn on this feature, when there is a call,
information or other reminder, the bracelet will vibrate, if closed,
the bracelet will only give a screen reminder without vibration.
Sedentary reminder: Set whether to open the sedentary reminder
function, you can set the reminder time interval in the profile, if
within a set time, you do not move and are inactive, the bracelet
will remind you to move.
Android user tips: The reminder function needs to be set to allow
"smart bracelet" running in the background; it is recommended to
add "smart bracelet" in the entitlement management to trust and
open all rights.
APP functions and settings:
Smart alarm clock
When connected three alarm clocks can be set. After setting, it will
be synchronized to the wristband;
Supports offline alarm, after the synchronization is successful,
even if the APP is not connected, the bracelet activate the
reminder as per the set time/s.
Bracelet display settings
In this option, you can set the function of hand-ring button to switch
the screen, pressing the function button can switch pages that
have been opened successively, and closed function will not
appear in the switch.
Intelligent anti-loss
Non-active disconnect (manually disconnect or exit the APP), the
bracelet will give an alert.
Looking for a bracelet
When connected, click the " find bracelet" option, the bracelet will
vibrate.
Shake to take pictures
In the connected state, enter the shake camera interface, shake
the bracelet, take photos automatically after 3 seconds countdown,
please allow APP to access the photo album to save the selfie.
Bracelet shows instructions:
Clock
After synchronizing with the phone, the bracelet will automatically
calibrate the time.
Pedometer
Wear the bracelet, record daily exercise steps; you can view the
current real-time steps. Step counter resets everyday 00:00.
Distance
Based on the number of walking steps, estimates the distance
traveled.
Calories
Estimate the calories burned according to the number of walking
steps.
Heart rate, blood pressure
After switching to the heart rate, blood pressure interface, wait for
a few seconds, it will show the current heart rate, blood pressure
test results. This feature requires bracelet support as well as a
heart rate and blood pressure sensor.
Sleep mode
Sleeping, the bracelet will automatically enter sleep monitoring
mode; automatically detect your sleep patterns; all night/light
sleep/awake times, calculate your sleep quality; sleep date
temporarily only supports APP-side view.
Note
Sleeping when wearing a bracelet will have sleep data, and the
next day after 9:00 will be synchronized to the APP.
Weather and temperature
Display local weather and temperature
Music setting
Back
Previous
The next song
Pause/Start
Band display settings
You can select online band display or use custom style
Common problem:
Why no reminder when the reminder function is enabled?
Android phone: Make sure the phone and the bracelet are
connected, even after connection open the corresponding
permissions in the phone settings to allow "Yoho Sports" APP to
access the caller SMS, address book and maintain the " Yoho
Sports " running in the background; If the phone is installed with
security software, add " Yoho Sports " as trusted source.
iPhone: If you do not get a reminder, it is recommended to restart
the phone to reconnect. When you connect the bracelet again, you
have to wait for the phone to pop up [Bluetooth pairing request],
click [Pairing] to remind you.
Heart rate and blood pressure test results are not accurate?
Measurements need to be done correctly; the bracelet is in contact
with the skin and stays connected with the arm and heart at the
same level for static measurements.
Bluetooth connection is abnormal, the bracelet display is
connected but the APP display is not connected.
1. Re-connect the bracelet to the APP
2. Enter the phone settings - Bluetooth, check whether the phone
is connected with the bracelet through Bluetooth, if the display
is connected, do not pair again after entering the APP.
3. Bluetooth connection is very unstable, always disconnected.
1. Android phones need the phone notification when connecting
to Bluetooth, check whether there is a Bluetooth pairing
request, if there is, please be sure to click on the pairing.
2. Please enter the phone settings - enter the Bluetooth menu, go
to the device that has been paired. Android mobile phone click
to cancel pairing; iPhone click to ignore this device; APP exit
the background, re-enter my device, and re-connect the
bracelet, the APP must keep running in the background.
How to monitor sleep, and when you can see the
synchronization of sleep data? Under the premise of wearing a
bracelet, when the user goes to sleep at night, the bracelet will
automatically switch to the monitor sleep mode. The detailed
sleep data will be synchronized to the APP after 9:00 the next
day. If there is no timely synchronization, click the
synchronization button in APP to manually synchronize.
Basic parameters:
Precautions:
1. During bathing and/or swimming the device should not be worn.
2. Please connect the bracelet when synchronizing data.
3. Use the correct charging cable.
4. Do not expose the bracelet to prolonged exposure to high
moisture or extreme temperatures.
5. When the bracelet crashes or reboots, please check the phone
memory, clear it and try again, or exit the APP to reopen it.
Parts introduction
1. *Host *Wristband *
2. Packing box
3. Manual
DE
Smartarmband Anleitung
Beschreibung:
Tragen des Armbandes
Es wird empfohlen, das Armband knapp über dem Handgelenk zu
tragen.
Stellen Sie das Armband je nach Größe des Handgelenks ein, bis
das Armband sicher und bequem sitzt, und schließen Sie dann die
Schnalle.
Der Sensor sollte dicht genug an der Haut liegen, um ein
Verrutschen zu vermeiden.
Aufladen des Armbandes
Laden Sie das Gerät vor dem ersten Nutzen vollständig auf. Wenn
der Batteriestand zu niedrig ist, arbeitet das Armband nicht korrekt.
Schließen Sie das Ladegerät zum Aufladen des Geräts an, dann
schaltet sich das Armband automatisch ein.
Ladeverfahren
Ziehen Sie das Band an beiden Enden des Armbandes ab.
Stecken Sie die USB-Seite des Armbandes in ein USB-Ladegerät
oder in einen USB-Anschluss des Computers.
Ladevorgang: komplett geladen:
Nutzen des Armbandes
Standby Seite: Abschalten:
Ein/Ausschalten
1. Drücken und halten Sie die Funktionstaste länger als 4
Sekunden, um das Gerät zu starten.
2. Drücken und halten Sie die Funktionstaste länger als 4
Sekunden, um in den Abschalt-Modus zu gelangen und drücken
Inhaltsverzeichnis
Sprachen:
Andere MOB Schrittzähler Handbücher
