MobiPrint MP T3 Bedienungsanleitung

MobiPrint MP T3

Portable Micro Printer

User’s Manual

www.mobilator.eu

２

Content

Operating Precautions··············································································3

Notes on Safety························································································3

Notes on Using·························································································3

Notes on Handling··················································································· 4

Chapter 1 Outer Appearance and Model··············································4

1.1 Outer Appearance·······························································4

1.2 Model Classification···························································5

Chapter 2 General Specifications ······················································· 5

2.1 Printing Specifications························································5

2.2 Physical Specifications·······················································5

2.3 Environmental Conditions··················································6

2.4 Other Specifications··························································· 6

Chapter 3 Operation··············································································6

3.1 Using Preparation······························································· 6

3.1.1 Battery Installation·························································· 6

3.1.2 Paper Installation····························································· 7

3.1.3 Buckle Installation···························································7

3.2 Operation Specifications···················································· 8

3.2.1 Printer On············································································8

3.2.2 Printer Off···········································································8

3.2.3 Self-test··············································································· 8

3.2.4 Paper Feeding····································································· 8

3.2.5 Battery Charging·································································8

3.3 Printer Setting····································································· 9

3.4 Printer Interface Connection and Printing························· 9

3.4.1 RS-232 Serial···································································9

3.4.2 RAW-Ir and IrDA····························································9

3.4.3 Bluetooth······································································· 10

3.5 Panel LED Indicators······················································· 10

Chapter 4 Printing Control Commands··············································11

Chapter 5 Other Information······························································ 25

Mobilator.eu

３

Operating Precautions

This section presents important information intended to ensure safe and

effective use of the printer. Please read the following carefully.

Notes on Safety

Be sure to use the specified battery and power source provided by our

company. Connection to an improper power source may cause fire,

explosion or damage to the printer.

Don’t put the battery into the fire or water, don’t disassemble or modify the

battery, don’t be short circuit, otherwise may result in injury or fire even

explosion.

If the printer would not be used for a long time, be sure to take off the

battery, otherwise the battery may leak liquid which is corrosive, if

improper operation causes battery leak, and the liquid is spattered on the

skin or clothes, please wash it with water, if spattered in the eyes, please

rinse them with water thoroughly and see a doctor.

Please do not open the paper case cover when it is printing or just when

printing is over, do not touch the print head with hand or body, overheat

may cause scald.

Notes on Using

Be sure not to print continuously over 1 meter, otherwise may cause

damage to the print head.

Water or other liquid should not spill into the printer, also the printer

should not be appeared in the rain, or else may cause printer damage.

Please do not open the paper case cover when it is printing, otherwise the

printer may work improperly.

If print with serial interface, should not unplug the interface cable in the

course of printing, or else some printing data may be lost.

When print in Ir or IrDA mode, be sure the Ir window of the host

equipment face rightly the Ir window of the printer, the distance should be

within the range of 50mm, and the angle should be within the range of 30o.

When print with Bluetooth interface, the communication distance should

be within 10 meters, otherwise the printer doesn’t print or prints rubbish

codes.

４

Too high（45℃）or too low（5℃） temperature and too high (85％)or too

low (20％) relative humidity both effect the print quality.

The print paper in poor quality or stored for too long time also may reduce

the print quality even damage the printer.

In the black mark detecting mode, the printer requires that the ready-print

black mark is accordant with the black mark printing rules (details please

refer to Chapter 5), otherwise the black mark can not be detected correctly.

Be sure to use up the electricity of the battery before charge it, as it can

ensure the using life of the battery.

Notes on Handling

The printer should be placed in such an environment that the temperature is

between -20℃and 60℃, and the relative humidity is between 5% and

95%.

If the printer will be stored for a long time, pleas be sure to take out the

battery, otherwise may damage the battery and printer.

Normal thermal paper can’t be kept too long, if you need to keep the

receipt for a long period, please choose long term effective thermal paper.

The print paper should be keep away from high temperature environment

and point-blank sunshine.

Chapter 1 Outer Appearance and Model

1.1 Outer Appearance

５

1.2 Model Classification

SP-RMTⅢ* *

A----Paper case cover is in arc shape, the diameter for

paper roll is 40mm.

B----Paper case cover is flat, the diameter for paper roll

is 30mm.

Ra---Raw_Infrared, RS-232 serial interface

Ir----IrDA(IrCOMM), RS-232 serial interface

BT---Bluetooth, RS-232 serial interface

Blank-Only RS-232 serial interface

Chapter 2 General Specifications

2.1 Printing Specifications

●Print method: thermal line printing

●Paper width: 58mm

●Print width: 48mm

●Resolution: 8 dots/mm (203dpi), 384 dots/line

●Print speed: 50mm／sec.

●Paper thickness: 60～80μm

●Character: Alphanumeric characters, extended graphics, international

characters, EAN13, EAN8 bar codes.

2.2 Physical Specifications

● Outline dimension: 77×102×44mm

● Weight: 275g (including paper roll and battery)

６

● Paper roll diameter: ≤40mm

● Interface: Bluetooth(only for TⅢBT model), IrCOMM (only for TⅢIr

model), Raw-Ir (9600bps ～115200bps) (only for T ⅢRa model),

RS232 serial (1200bps～115200bps)

2.3 Environmental Conditions

● Operation temperature: 5～45℃

Relative humidity: 20%～85%

● Storage temperature: -20～70℃

Relative humidity: 5%～95%

2.4 Other Features

● Paper loading method: drop-in easy loading (details please refer to

3.1.2 Paper Installation).

● Black mark localization: available (details please see 4.2 ready printing

black mark specification).

● Paper out detection: when paper is out, the Mode indicator blinks, and

the buzzer rings twice.

● Print commands: ESC/POS compatible command set (refer to Chapter

4).

● Power supply: 1500mAh rechargeable polymer lithium battery.

● Low power alarm: when the battery is low, the power indicator blinks

with red color and the buzzer rings 3 times; if the printer is in sleeping

mode, the printer will cut off power after the buzzer rings 3 times.

● Sleeping: the printer will fall after at least 2 seconds without usage into

sleep, and can be awaken by pressing【FEED】button or sending data

to it.

● Battery full charge time: 3 hours.

● Battery duration: under 25% print density, at least 100 meters, the

standby time is over 15 days.

Chapter 3 Operation

3.1 Using Preparation

3.1.1 Battery Installation

７

3.1.2 Paper Installation

3.1.3 Buckle Installation

８

3.2 Operation Specifications

3.2.1 Printer On

The printer is powered on by pressing the power button; the power

indicator is on with green color whenever the printer is on.

Notice: when the batter is almost exhausted, the power indicator blinks

with red color, in this case, you must charge the battery by using the

adaptor. The method of charging the battery, please refer to 3.2.5.

3.2.2 Printer Off

The printer is off after hold down the power button. All the indicators are

off whenever the printer is off.

3.2.3 Self-test

The self-test checks the printer’s current settings, status and whether the

printer has any problems. Turn on the power while holding down the

FEED button, the self-test begins.

The printer is ready to receive data as soon as it completes the self-test.

3.2.4 Paper Feeding

When the printer works normally, hold down【FEED】button, the paper

feeding begins, and stops when hold down

【FEED】

button again. When the

printer works in black mark mode, hold down【FEED】button, the printer

begins to feed paper and stops at the position of black mark. If the paper is

not black mark paper, the printer stops automatically after feeds paper for

30cm.

3.2.5 Battery Charging

The power indicator becomes red when the power of the battery is run out,

so charging the battery is required in this situation.

The charging method is as following: turn off the printer, connect the

adapter to the power socket with 220V, 50HZ, then plug the power

charging cable to the power socket of the printer, so the power charging

begins, during the course of power charging, the 【FEED】indicator goes

green, and becomes dark when the charging is over.

Notice: it would better not turn on the printer during the course of charging

power, lest the charging time goes longer, moreover, be sure not to use the

printer to print when the battery is charging.

when the battery is low, the power indicator blinks with red color and the

buzzer rings 3 times; if the printer is in sleeping mode, the printer will cut

９

off power after the buzzer rings 3 times. In this case, you must charge the

battery by using the adaptor.

Charging battery method:

The TⅢuses a Lithium rechargeable battery pack. Before first use, the

battery pack should be charged for at least 4 hours. To prevent electrical

damage to the printer and/or battery pack, please use approved AC/DC

adapter only. During charging, the

【FEED】

indicator is green, and when the

battery is charged fully, the【FEED】indicator is turned off automatically.

3.3 Printer Setting

Users can set the printer by using the 〈TⅢSetting Tools 〉software

provided by us. The settings include: serial baud rate, RAW-IR baud rate,

Bluetooth device name and password etc. Regard to the setting method

please refer to the〈TⅢSetting Tools〉

3.4 Printer Interface Connection and Printing

3.4.1 RS-232 Serial Interface

The standard accessories for T Ⅲprinter include: DB-9 serial interface

cable (one end is D model standard serial interface socket, connected to

host computer, the other end is PS/2 socket, connected to printer).

When connect the serial interface, if it works normally, then the printer

stops to received data from Bluetooth, Ir interface or IrCOMM interface.

The serial interface of the printer is RS-232, the baud rate range is:1200bps,

2400bps, 4800bps, 9600bps, 19200bps, 57600bps, 115200bps. The baud

rate selection please see 3.3 printer settings.

3.4.2 RAW-Ir and IrDA Connection

The hardware of TⅢwith infrared port printer is compatible with IrDA1.1.

IrCOMM protocol is one of the sub-protocol of IrDA and widely used in

portable devices. RAW-Ir data transmission mode can be connected to the

devices with raw infrared port for printing, while IrCOMM mode can be

connected to the devices with IrCOMM protocol for printing.

RAW-Ir can work under 9600bps, 19200bps, 38400bps, 57600bps,

115200bps, the baud rate of RAW-Ir is same to that of serial interface.

Notice:

1) To use the TⅢ’s infrared port, a computer or Personal Digital Assistant

(PDA) with IR port is required.

2) Position a PDA conforming to the specifications in point not more than

１０

50 centimeter away from the printer’s infrared port. Make sure the two

ports are in front of each other with an angle of not more than 30° on the

four side.

3.4.3 Bluetooth Connection

PDA, Laptop and other communication devices with Bluetooth can drive T

Ⅲ-BT to print by the Bluetooth interface. T Ⅲ-BT is compatible with

Bluetooth 2.0 protocol. Power grade is CLASS 2; effective communication

distance is 10 meters. The name of the printer is SPRT T Ⅲ, the initial

password is “1234”; users can change the printer name and password by

using〈TⅢSetting Tools〉.

The method for the pairing between TⅢ-BT with the host device is:

1. Turn on the printer;

2. Host device searches for the outer Bluetooth device;

3. If there are other Bluetooth devices, please select SPRT TⅢprinter;

4. Put in password “1234”

5. Pairing finished.

Notice: If the printer name has been changed, please be sure not turn on

more than one printer, otherwise it will be difficult to justify which printer

been paired.

3.5 Indicators and Buzzer

There are three indicators for TⅢprinter, they are【MODE】,【FEED】

and 【POWER 】indicator, the anterior two indicators are green, power

indicator has two colors: red and green. The following is the meaning of

each indicator denotes:

【MODE】indicator:

Solid GREEN: printer is in setting status

Green LED blinking （one time）: printer out of paper

Green LED blinking （twice）: high temperature error

【FEED】indicator:

Solid GREEN:battery charging

Green LED off: battery at full charge

【POWER】indicator:

Solid GREEN:power on

Solid RED: low battery

The TⅢuses a buzzer to indicate various status of the printer. The

Inhaltsverzeichnis

Andere MobiPrint Drucker Handbücher

MobiPrint

MobiPrint MP-T7BT Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung