Mocom solstice series Bedienungsanleitung
1
Mocom Concaved Screen –Solstice Series
Assembly / Installation Guide
Please read rules and instruction carefully.
Caution!
The following information should be thoroughly understood before start assembling the product.
The screen surface is vulnerable to external shocks; attention is required when you set it down on the
floor (Please note that strong external shock may affect or damage the screen and a screen curvature)
Please check all components (Bolts, nuts, washers, brackets and the screen)
Select a proper area (indoor) for assembly.
Remove items from your top pocket to avoid them falling out onto the screen surface.
Pull the plastic covering of the screen to a side gently. Do not attempt to apply force with hands or a knife.
If possible, cooperation of two or more is required; one person holds the screen horizontally and the
others can have the plastic easily by pulling it aside. The screen can be placed vertically
Note there are side handles for some models. Please use them to ensure the screens are handled correctly.
While assembling, lean screen surface on the wall in a safe area to prevent from possible damage.
Do not touch the screen surface (The screen surface can be scratched or finger-marked).
Do not touch the screen surface with hard objects.
Alcohol, acetone, organic solvents and other strong cleaning agents are prohibited to remove dirt or debris
on the screen surface. (This may cause damage on the surface of the screen) When cleaning is needed,
wipe any dust from the screen surface with static-free cloth or brush or use dryer with cold air to dust
away.
Please put a screen cover over the screen while the screen is not being used.
Place the screen back in the carton face down
The caster lock wheels must to be in locked location when stationery or when alignment.
Never re-locate screen together with floor stands. Always disassemble screen before move.
In you have any questions regarding the proper assembly, contact your dealer or representatives.
2
Installation Method by a screen model
MDW-105/125/135
EPDM black frame (22.5mm width) with molded back panel
MDW-105S/125S/135S
EPDM black-slim frame (10.5mm width) with molded back panel
DHS-105/125/135
Black velvet finished Aluminum frame (50mm width) with molded back panel
DHS-105N/125N/135N
Black velvet finished Aluminum frame (55mm width) with slim molded back panel
MDW-155/175/200/220/250
Black steel frame (25mm width) front and back steel squared pipe frame (without
molded back panel)
Model
Wall-Hook type
Wall-Hanger type
Floor Stand
S3D-82
WH
OW-1
OS-1
MDW-105/105S/DHS-105
OW-2
OS-2
MDW-125/125S/DHS-125
OW-3
OS-3
MDW-135/135S/DHS-135
OW-3
OS-4
DHS-105N
X
NW
NS-1
DHS-125N
X
NS-2
DHS-135N
X
NS-3
MDW-155/175/200/220/250
Anchoring on the wall
“A” Type
3
WALL MOUNTING
Wall-Hook Type (WH Model)
(For: S3D-82, MDW-105/125,/135, MDW-105S/125S/135S, DHS-105/125/135)
This Wall-hook type is used when the projector is installed on the ceiling with a low height
and at a place where only a limited adjustment angle of the screen is allowed.
Advantage of using this type is a short separation distance between the wall and the screen.
Note that the position of the screen is fixed.
It cannot be used when a projector is positioned on the table top, because the angle toward
top adjustment is limited.
Supplied accessories include the following.
(1) Hook Brackets on top: 2 ea
(2) Screen Angle Adjuster on bottom: 2 ea
(3) Wall Bracket on top of wall side: 2 ea
accessories not included :
For (3) Wall bracket
For concrete wall
For wood wall
Anchor bolts
Screws
M6 / 8 - 12units
8 - 12units
4
Installation of Wall-Hook Type
i. Assemble the accessory (1)Hook Brackets and (2) Angle Adjuster to the screen body.
((1) Hook Bracket can be pre-assembled)
ii. Fix the (3) Wall Bracket with screws or anchor bolts on the wall according to an
installation height of the screen. (the saw blade situated upwards)
iii. Put the upper part of the screen on (3) Wall Bracket
iv. Adjust an angle of the upper part of the screen in order to obtain an optimum brightness
and fix it (2) Angle Adjuster (Go to the page 15)
(1)
(2)
(3) Wall Bracket
(2) Angle Adjuster
5
Wall-Hanger Type (OW-1/2/3)
(For: S3D-82, MDW-105/125,/135, MDW-105S/125S/135S, DHS-105/125/135)
This wall-hanger type is used when the projector is installed on the ceiling with a tall height
or on the table top.
This is applied to a location where space for adjustment of the angle of the screen is enough.
Note that the separation distance between the wall and the screen is big. And it allows the
screen to move to the left and the right slightly to position easy.
Supplied accessories include the following.
(1) Hanger at screen side : 2 ea
(2) Wing nuts : 6 ea
(3) Screen Angle Adjuster on bottom (on the wall side)
: 1 ea or 2 ea
(4) Hanger Bracket on the wall side : 1 ea
accessories not included :
For (3) Angle adjuster
For (4) Hanger Bracket
For wood wall
Screws
2units
For concrete wall
For wood wall
Anchor bolts
Screws
M6 / 4 units
4units
6
Installation of Wall-Hanger Type (OW-1,2,3)
①Assemble the accessory (1) Hanger to the screen body
using (2) Wing nuts
②Install the (4) Hanger Bracket on the wall using anchor
bolts or screws, setting at 6-inches higher than the
horizontal axis of the screen.
③Set the (3) Angle adjuster on the wall using a screw.
(The angle adjuster can be disassembled, then there is
a hole in angle adjuster and use screw to nail on the
wall) at 20~30 inches below the hanger
④Put the screen on the (4) Hanger
Bracket
⑤Adjust an angle of the screen in order to
obtain an optimum brightness and fix it
with the accessory (3) angle adjuster
(Go to the page 15)
7
Wall-Hanger Type for DHS - 105N/125N/135N (NW)
(For: DHS-105N/125N/135N)
This model (DHS-XXXN) screen is for a home theater and its frame has a black velvet finishing
job on aluminum. Using a thin back panel, it has excellent design. The black-velvet finished
portion absorbs a video image exceeding a margin.
The position of the projector can be either on the ceiling or on the table top.
Though a separation distance between the wall and the screen is small, an installation position
of the wall bracket is fixed. .
Supplied accessories include the below.
(1) Hanger at screen side: 2ea
(2) Hanger Bracket at wall side: 2ea
accessories not included :
for (2) Hanger Bracket
For concrete wall
For wood wall
Anchor bolts
Screws
M6 / 4-6 units
4-6units
8
Installation of Wall-Hanger Type (NW)
①Assemble the accessory (1) Hanger to the screen body
②Fix the accessory (2) Hanger Bracket on the wall using
anchor bolts or screws.
③Adjust an angle of the screen in order to obtain an
optimum brightness and fix it tight. (Go to the page 15)
9
Wall mounted by Anchoring on the wall
(For MDW-155/175/200/220/250)
For models with a large screen, there is no back panel but supports with steel frame, and the
screen cannot be installed in a method of the wall bracket.
Anchor the screen directly to a wall surface and adjust an angle of the screen according to an
anchor’s length.
Prepare…
1) Heavy-duty Anchors bolts and nuts (M10, M12 is preferable) –
Recommended to use at least 4 to 6 units, Choose the length of the bolts depending on the angle
adjustment of the screen. (Use longer anchor bolts for larger angle adjustment)
Size (A)
Cab length
(E)
Anchor
Length(B)
the thread of
a screw ( C )
Drill bit
Diameter
(D) (mm)
Anchor
perforation
depth (mm)
Proof
Weight
(kgf)
3/8”(M10)
40
3”(75mm)
45
14
44
2300
4”(100mm)
70
5”(125mm)
85
6”(150mm)
100
8”(200mm)
150
10”(250mm)
180
12”(300mm)
230
1/2”(M12)
50
4”(100mm)
60
17
55
3200
5”(125mm)
75
6”(150mm)
100
8”(200mm)
150
10”(250mm)
180
12”(300mm)
230
1) Electric (concrete) hand drill -1 6) Chain block ( 0.5 ton) –2
2) A hammer drill - 1 7) Aluminum ladder –1
3) Ruler –1
4) Spanner -- 2
5) Scaffolding –1 , If necessary
10
Wall
Installation
1) Determine the Anchor bolts locations and mark where you will anchor it.
Rear side of the screen
2) Drill holes for the anchor bolts.
3) Place the anchor bolt into the cement wall.
4) Lift screen with chain block or other equipment
5) Insert screen into pre-installed anchor bolts
6) Insert anchor nut smoothly.
7) Adjust the screen angle by adjusting anchor nut length (Go to the page 15)
8) Tighten anchor nuts after determine the screen angles.
A length of the anchor must be sufficient enough to adjust an angle.
Cover the screen surface and do not touch the surface during the installation to prevent damage
.
Wall
Wall
Anchor
Hammer Drill
D
A
Inhaltsverzeichnis
Beliebte Projektionsfläche Handbücher anderer Marken
FART PRODUKT
FART PRODUKT Standard SCREEN Bedienungsanleitung
Draper
Draper E Series Handbuch
Elite Screens
Elite Screens Elite Tripod Series Bedienungsanleitung
Laarhoven
Laarhoven Companion II Bedienungsanleitung
Renogy
Renogy RMS-LFPS-US Bedienungsanleitung
Da-Lite
Da-Lite ExecutiveElectrol Bedienungsanleitung
