Modena SX 9502 V Betriebsanleitung

User

Manual Book

Slim Hood

Fresco Series

SX 9502 V, SX 9502 S, SX 6501 V

SX 6501 S, SX 9512 L, SX 7511 L

SX 9412 L, SX 9412 S

SX 7412 L, SX 7412 S

Forte Series

SX 9122 L, SX 9002 S, SX 7121 L,

SX 6001 S

TABLE OF CONTENTS

Part 1: Safety Warnings 3

Part 2: Name of Parts 4

Part 3: Installation 5

Part 4: How to Use 10

Part 5: Maintenance 12

Part 6: Troubleshooting 13

Part 7: Precaution 14

Part 8: Specification 15

This guide book explains everything you need to know about your new

product. Please contact our Customer Care should you need further

assistance through www.modena.com

•Do not allow children to operate the unit.

•This exhaust hood is designed for home use only, not suitable for the

environmental condition, bake shop, barbecue, and other commercial

purposes.

•The exhaust hood should be cleaned periodically so that its power is

maintained.

•Clean the exhaust hood according to the instructions contained in this book and

keeps it away from the danger of being burnt.

•No direct grilling on a gas stove.

•Keep your kitchen remains good circulation.

•Before connecting the unit to a power source, make sure the power cord is in

good shape. If there is damage to the power cord, the replacement must be

performed by qualified personnel or contact the MODENA Service Center for

replacement process.

•The room should have good ventilation during the use of exhaust hood on gas

stoves or other fuels.

•The exhaust hood waste pipe should be separated with an air-duct.

•Regulations regarding the air exhaust must be met.

•The unit is not intended to be used by persons (including children) with a

physical, sensory, or mental disability, or lack of experience and knowledge

unless they have been given supervision or instructions concerning the use of

the appliance by the person who is responsible for their safety.

•Children should be supervised to ensure that they are not playing with the unit.

•Do not strike a fire under the sucker of the exhaust hood.

•The exhaust hood is not aimed to be installed on top of the stove that had more

than four burners.

Electrical Shock Hazards

•Connect the unit only to a grounded power socket correctly. If you are in doubt,

ask advice from an experienced technician who is suitably qualified.

•The failure to follow these instructions may cause electric shock, fire, or other

hazards that are fatal.

PART 1: SAFETY WARNINGS

SX 6501 S, SX 6501 V, SX 9502 S, and SX 9502 V

Carbon Filter

Directional Knob

Grid

Aluminum Filter

Lamp

Control Panel

Air Flow Direction Glass

SX 9512 L,SX 7511 L, SX 9412 L, SX 9412 S,SX 7412 L, & SX 7412 S

Carbon Filter

Direction knob

Control Panel

Lamp

Aluminum Filter

Filter locker

* Image is a general overview and is not necessarily the same as the product you

receive

PART 2: NAME OF PARTS

Exhaust hood is equipment which sucks smoke and cooking fragrance. With a vent

hood, your kitchen will be free from oil particles that may produce bad odor.

Check the strength of wall on which the

exhaust hood is to be installed. Make sure

the wall can sustain the weight / load of

the vent hood.

The exhaust hood should be installed

precisely over the stove at a vertical

distance of 65 - 75 cm from the stove

surface.

Installing the Exhaust Hood on the Wall

Exhaust hood must be installed

perpendicularly to prevent the oil from

flowing to one side and dripping out of the

vent hood.

Preparations to Be Made Before Installing the Exhaust Hood

Remove the exhaust hood from its

packaging and put it on an even place (eg.

Tables).

Open the grid by sliding the right and left

grid locker (A) and then pull it. Remove the

spigot / flange (pipe connector) and the

hole cover from the plastic bag.

Turn the air directing knob to the following position:

a. Exterior symbol for ducting / exhaust system

Interior symbol for recirculation system

PART 3: INSTALLATION

Cover the grid

The exhaust hood has two holes on it: Hole

and Hole

(look at the picture). To install the

spigot/flange and hole cover, follow these

instructions:

•For ducting / exhaust system:

Install the spigot / flange G on one of the air

holes, either D or E. Holes which do not

have spigot / flange shall be covered with

Hole Cover H.

•For recirculation system:

Both air holes D and E shall be covered with

the available plastic Hole Cover.

Instalation of Exhaust Hood

Exhaust hood can be installed on the concrete (brick) wall or the bottom

part of the kitchen set.

Installing on concrete (brick) wall

Draw a centerline on the wall where the

exhaust hood is to be installed (1).

Post a template for drilling on the wall

(2). If no template is available, attach

the exhaust hood on the wall and mark

the spot on the wall where a hole is to

be made.

Create holes on the four marks with a 6 mm diameter drill bit or fisher size

(3), and then insert the fisher to the four holes (4).

Install the screw on both upper holes

and set aside 1 cm between the head of

the screw and the wall surface (5).

Install the exhaust hood on the screwed

wall by suspending the vent hood on the

screw (6).

When the exhaust hood is positioned correctly on the wall, tighten both

screws on the upper part (7).

To reinforce the exhaust hood handle on the wall, install the screws on both

holes on the bottom part (8) and tighten them (9).

Close the grid

Connect the exhaust system with the spigot / flange if the exhaust hood is

to be operated as a ducting / exhaust system.

Installation on the bottom part of the kitchen set

Put the exhaust hood on the bottom

part of the kitchen set in accordance

with the planned position.

Mark the bottom part of the kitchen set

for flexible pipe hole and then creates a

hole if the exhaust hood is to be

operated with ducting / exhaust system.

Install the exhaust hood with 4 screws

on the prepared position.

To reinforce the exhaust hood handle on the kitchen set, install the screws

on other holes on the upper part and tighten them.

Connect the exhaust system with the spigot / flange if the exhaust hood is

to be operated as a ducting / exhaust system.

ATTENTION:

Before drilling, make sure that there is no cable installation, water pipe and

installation inside the wall.

Operating Procedure

MODENA Exhaust Hood has 2 (two) work methods as follows:

Ducting / Exhaust System:

•

In this mode, the exhaust hood operates

by sucking the smoke / cooking odor

and then discharging it out of the vent.

•

A heat / fire-resistant ducting system is

required to discharge smoke / odor out

of the vent.

•

To connect the exhaust hood with the

discharge duct, use "spigot/flange" is

designed with a diameter of 100 or 125

mm.

Several things which require attention in installing the ducting system exhaust

hood:

Carbon filter must be removed because

the cooking odor will be sucked and

immediately discharged out of the

room.

The suction force will be diminished if

the exhaust system is too long and there

are too many elbows.

Do not connect the exhaust system with

a chimney or an air duct or hot steam

duct.

If the exhaust hood is to be installed in a multi-storied building or an

apartment, consult with the person in charge of the building / apartment

prior to installing the exhaust system.

Exhaust hood with ducting system should be used in an open-air room with

good air circulation.

Recirculating system:

In this version, the exhaust hood sucks the

smoke / cooking odor and filters it through

an aluminum filter and carbon filter. The

filtered smoke is then re-circulated into the

room. This system is used if the premise

renders it impossible to install a ducting

system.

Several things which must be ensured when

installing a exhaust hood with recirculation

system:

Both carbon filter and aluminum filter must be used.

The position of both filters must be correct.

Holes where air duct is discharged found in the front cabinet of the exhaust

hood cannot be closed.

Electricity Connection

MODENA Exhaust Hood is designed for 220 volt electricity input, single phase

with 50 Hz of frequency. This appliance uses a double-insulated power cord (2

parallel cords) and should not be connected to a grounding wire.

ATTENTION:

Overall installation should be performed by a competent person in the field of

electrical or able to do the installation. If you will do the installation yourself,

it is recommended that at first consult to the Service Center Modena.

Details of the method and frequency of cleaning listed in the "Installation and

Maintenance"

To separate the equipment from the power source should not attract a wired

connection, but the pull of the base / head power cable.

•

Connect the power cord with an electrical outlet.

•

Slide or press the motor speed regulator button and light switch to turn

vent hood on or off as shown in the following picture.

Push Button

Indicator lamp

Button used for turning lamp on / off

Button for turning off the exhaust hood

Motor speed button –LOW

Motor speed button –MEDIUM

Motor speed button - HIGH

Slide Button

Symbol

To turn on/off the light

To turn off the motor

LOW motor speed

MEDIUM motor speed

HIGH motor speed

PART 4: HOW TO USE

NOTES:

Adjust the motor speed of the vent hood according to the thickness of smoke

/ steam generated by the cooking process.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Modena Dunstabzugshaube Handbücher

Modena

Modena Luce Series Betriebsanleitung

Modena

Modena RX Series Bedienungsanleitung

Modena

Modena DX Series Bedienungsanleitung

Modena

Modena CX 9150 Betriebsanleitung

Modena

Modena PX 7111 Bedienungsanleitung

Modena

Modena CX 6761 Betriebsanleitung

Modena

Modena Esile Series Betriebsanleitung

Modena

Modena PX 7111 ZMNA Betriebsanleitung

Modena

Modena IX Series Bedienungsanleitung

Modena

Modena RX Series Betriebsanleitung

Modena

Modena PX Series Bedienungsanleitung

Modena

Modena CX Series Bedienungsanleitung

Modena

Modena PX 9022 Bedienungsanleitung

Modena

Modena CX 9761 Betriebsanleitung

Modena

Modena Fresco Series Betriebsanleitung

Modena

Modena Moderno Series Betriebsanleitung

Modena

Modena Imola Series Betriebsanleitung

Modena

Modena BX 9603 Bedienungsanleitung

Modena

Modena SX Series Bedienungsanleitung

Modena

Modena IX 9330 Bedienungsanleitung

Modena

Modena PX Series Betriebsanleitung

Modena

Modena Piazza Series Betriebsanleitung

Modena

Modena Cesena Series Betriebsanleitung

Modena

Modena CX 9306 Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch