Modena Tiziano Series Betriebsanleitung

User

Manual Book

Washing Machine

Tiziano Series

WF 830

Thank you for your trust in choosing MODENA products for your household

needs. With your satisfaction as our priority, we constantly aim to deliver stylishly

designed products equipped with state-of-the-art technology to assist you in

your daily activities.

This is your guidebook containing everything you need to know about our

product. Please reach out to us if you need further assistance or other

information via our Customer Care or our official website www.modena.com.

CONTENTS PAGE.

• Introduction 20

• Part 1 : Name of Parts 22

• Part 2 : Understanding Control Panel 22

• Part 3 : First Step Before Installation 23

• Part 4 : Installation 23

• Part 5 : How to Use 25

• Part 6 : Maintenance 30

• Part 7 : Precaution Action 32

• Part 8 : Troubleshooting 34

• Part 9 : Specification 36

• Appendix 1: International Textile Care Label 37

• Appendix 2: Useful Hint For Dirt Vanishing 38

1. Control Panel 6. Inlet Valve (Cold) 11. Back Cover

2. Drawer Handle 7. Drain Hose Clips 12. Power plug

3. Door 8. Power Cord

4. Pump Case Cover 9. Drain Hose

5. Legs 10. Trasit Bolt

* Features and accessories are depended on product series.

Part 1: Parts Name

WF 830

When the installation is ready, make sure that the power supply has fuse with the specification of 15A,

220V, 50 Hz. When the heating function is used, the maximum current of the washing machine is 10A.

Make sure the power supply (current, voltage, and cable) fills the requirement to operate this appliance

on a normal load.

-The washing machine must be grounded, so whenever there is a problem, the current can be

conducted to the ground and minimize the risk of short circuits. If you are not sure if the washing

machine has been properly grounded or not, you can contact the experienced technician.

-The pressure of supply water is between 50kPa until 800kPa for the normal operation of the

washing machine. If the water supply is too low, the input water valve may not work normally or the

washing time becomes longer, and the display will show error code”E4”.

Part 2: Understanding Control Panel

Part 3: First Step Before Installation

Control Panel Description

1. Power Button 6.Speed Button

2. Program Select 7.Rinse Button

3. Start/Pause Button 8.Delay Button

4.Anti-bacteria Button 9.Wash Button

5.Temperature Button

-Check all connections on input water supply, valve, and faucet to avoid water leakage.

-The result of the washing machine depends on the effectiveness of the detergent. The dirt on the

clothes may not be able to vanish by using bad quality detergent. Please clean the dirt on the

clothes like explained on this book before being washed by washing machine.

Take the washing machine out from the cardboard box and put it on a flat and sturdy floor. Don’t place

the washing machine on an incline, not flat, on the carpet, or on the wooden floor. Don’t place the

washing machine outdoor, and avoid a humid place that can cause damage.

1. Loosen all bolts behind the washing machine

-For transportation purposes, this washing

machine is locked with added polyfoam.

Before operating the washing machine,

loosen all bolts like the picture on the right.

-Fill the holes with supplied covers at the

back of the washing machine.

-Keep the polyfoam and bolts for transportation purposes and

use it again before transporting the washing machine.

Part 4: Installation

2. Leg adjustment

Install or place the washing machine at a temperature of no less than 0°C and not outdoors

because it may damage the programming controller

Note: To facilitate the installation, the feet may not be locked from the factory. Please

be sure to lock all the feet before adjusting the level!

3. Connect Inlet Valve

a) Water Inlet

- Connect the water hose to the water inlet on the back of the

washing machine.

- Connect the other side of the hose with the faucet.

- Don’t pull the hose if it is too short. Change to a longer hose.

- Check if there is leakage on connection

with the faucet.

b) Drainage

- If there is any leakage with the hose after the

connection, then repeat the steps to connect the

inlet hose.

- Do not bend the hose.

- Check for the inlet hose connection carefully

before using the washer every time.

Connect the drain hose

- The drain hose should be placed at a height of

65-100cm above the floor. Otherwise, it can

cause poor drainage.

- You can use the supplied drain hose support

bracket to loop the drain hose down into the

wall, standpipe or laundry tub.

- Make sure all the hose connections are

properly and tightly installed t.

The end of the drain hose cannot be submerged in

water to make the washer work properly.

4. Connecting with electricity

- Make sure the voltage used is 220 volts and 50 Hz.

- Insert the power cord to the socket that is connected to the

ground.

- Avoid using extension cables, adapters and multiple sockets.

Attention!

Before operating the machine, it is suggested to check things as follows:

- Is the washing machine door closed properly?

- Is the water faucet opened?

- Is the drain hose placed correctly?

- Is the electricity connected?

In every washing make sure that:

- The connector of water supplies are safe, the water tap is turned on and the

drain hose has been placed in the right position.

- Cycle Options (P) or the power button is OFF.

- Then, with dry hands, plug the power cord into the wall socket.

- Sort / sorting clothes to be washed by the type of fabric / material.

- Make sure there are no objects (such as coins, safety pins, etc.) in the pocket

of the laundry that will be washed because it may damage the washing

machine, filters, and clothes itself.

- Open the washing machine door.

- Put in the clothing that will be washed (make sure the weight of the clothing

put into the washing machine does not exceed the capacity of the washing

machine) and close the washing machine door.

Detergent Drawer

The detergent drawer contains these parts:

Part 5: How to Use

- Detergent container for Prewash I → Powder detergent

- Detergent container for main wash II → Powder or liquid detergent

- Container for softener. ( ).

Caution: Don’t open the drawer during washing process.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Modena Waschmaschine Handbücher

Modena

Modena WF 741 WAM Betriebsanleitung

Modena

Modena WF 1030 VDWH Betriebsanleitung

Modena

Modena WT 1121 WAM Betriebsanleitung

Modena

Modena Semplice Series Betriebsanleitung

Modena

Modena WF Series Bedienungsanleitung

Modena

Modena WF 0652 WSR Betriebsanleitung

Modena

Modena WF 652 Bedienungsanleitung

Modena

Modena WF 0532 WSR Betriebsanleitung

Modena

Modena WT 1120 UFWH Betriebsanleitung

Modena

Modena WT 0820 UGWH Betriebsanleitung

Modena

Modena WF 1156 Betriebsanleitung

Modena

Modena Calma Series Betriebsanleitung

Modena

Modena WF 730 Betriebsanleitung

Modena

Modena WF Series Bedienungsanleitung

Modena

Modena WT 1081 WTM Betriebsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung

Beko

Beko WKB 51231 PTMA Bedienungsanleitung