Modern Flames Landscape Pro Multi Series Betriebsanleitung

SERIAL NUMBER:________________________________________

Landscape Pro Multi Series

LPM-4416 • LPM-5616 • LPM-6816 • LPM-8016 • LPM-9616

INSTALLATION/OWNERS MANUAL

FOR USE IN UNITED STATES AND CANADA

USER INSTRUCTIONS

LANDSCAPE PRO MULTI SERIES

LPM-4416 • LPM-5616 • LPM-6816 • LPM-8016 • LPM-9616

SAFETY INFORMATION AND OPERATIONS MANUAL

Read these instructions completely before beginning installation. Failure to follow them could

cause a heater malfunction resulting in serious injury and/or property damage.

WARNING: All electric heaters have hot and arcing or sparking parts inside. Do not use it in

areas where gasoline, paint or ﬂammable liquids are or are stored.

This ﬁreplace meets the construction and safety standards of H.U.D. for application in

manufactured homes when installed according to these instructions.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

USER INSTRUCTIONS

TABLE OF CONTENTS

When using electrical heaters, basic

precautions should always be followed to

reduce the risk of ﬁre, electric shock and injury

to persons, including the following:

1. Read all instructions before installing or

using this heater.

2. This heater is hot when in use. To avoid

burns, do not let bare skin touch hot

surfaces. Keep combustible materials,

such as furniture, pillows, bedding, papers,

clothes, and curtains at least 3 feet (0.9m)

from the front of the heater and keep them

away from the sides and rear.

3. Extreme caution is necessary when any

heater is used by or near children or

disabled people and whenever the heater is

left operating and unattended.

4. Do not operate any heater after it

malfunctions, has been dropped, or

damaged in any manner. Disconnect power

at service panel and have heater inspected

by an authorized technician or a reputable

electrician before using.

5. Do not use outdoors.

6. To disconnect heater, turn controls to oﬀ

and turn oﬀpower to heater circuit at main

disconnect panel.

7. Do not insert or allow foreign objects to

enter any ventilation or exhaust opening as

this may cause an electric shock or ﬁre, or

damage the heater.

8. To prevent a possible ﬁre, do not block air

intakes or exhaust in any manner.

9. A heater has hot and arcing or sparking

parts inside. Do not use it in areas where

gasoline, paint or ﬂammable vapors or

liquids are used or stored.

10.Use this heater only as described in this

manual. Any other use not recommended

by the manufacturer may cause ﬁre, electric

shock or injury to persons.

11. SAVE THESE INSTRUCTIONS

WARNING: Improper installation,

adjustment, alteration, service or

maintenance can cause injury or property

damage. Refer to this manual. For

assistance or additional information,

consult a qualiﬁed installer.

CAUTION: Do not expose the heater to the

elements (such as rain, etc).

Do not place clothing or other ﬂammable

material on or near ﬁrebox. Never place

any objects on the ﬁreplace.

Carefully supervise young children when

they are in the room with ﬁreplace.

Fireplace becomes very hot when running.

Keep children and adults away from

hot surfaces to avoid burns or clothing

ignition. Fireplace will remain hot for a

time after shutdown. Allow surfaces to

cool before touching.

CAUTION: In order to avoid

overheating, do not cover the

heater.

IMPORTANT INSTRUCTIONS

Important Instructions 3

Power Data 4

Product Guide 4

Box Contents 5

Installation 6

Operation 12

Service Parts 13

Troubleshooting 15

Frequently Asked Questions 16

Cleaning and Maintenance Instructions 17

Wiring Diagram 17

USER INSTRUCTIONS

POWER DATA

PRODUCT GUIDE

LPM-4416 LPM-5616 LPM-6816 LPM-8016 LPM-9616

Volts/HZ

Amps

AC 120V 60Hz

14 Amps

Optional AC

240V 60Hz

14 Amps

AC 120V 60Hz

14 Amps

Optional AC

240V 60Hz

14 Amps

AC 120V 60Hz

14 Amps

Optional AC

240V 60Hz

14 Amps

AC 120V 60Hz

14 Amps

Optional AC

240V 60Hz

14 Amps

AC 120V 60Hz

14 Amps

Optional AC

240V 60Hz

14 Amps

Heater

AC 120V 1500W

Optional AC

240V 3000W

AC 120V 1500W

Optional AC

240V 3000W

AC 120V 1500W

Optional AC

240V 3000W

AC 120V 1500W

Optional AC

240V 3000W

AC 120V 1500W

Optional AC

240V 3000W

Lamps LED 12V LED 12V LED 12V LED 12V LED 12V

Rotor Motor

AC120V/60Hz

40mA 3.7W

18/15RPM CCW

AC120V/60Hz

40mA 3.7W

18/15RPM CCW

AC120V/60Hz

40mA 3.7W

18/15RPM CCW

AC120V/60Hz

40mA 3.7W

18/15RPM CCW

AC120V/60Hz

40mA 3.7W

18/15RPM CCW

Shipping

Size

46 ⁷⁄” x 27” x

15 ¹⁄”

58 ⁵⁄” x 27” x

15 ¹⁄”

70 ¹⁄” x 27 ¹⁄” x

15 ¹⁄”

82 ¹⁄” x 27 ¹⁄” x

15 ¹⁄”

98 ¹⁄” x 27 ¹⁄” x

15 ¹⁄”

Model Viewing Area Firebox Dimensions Framing Dimensions

LPM-4416 42” W x 15 ¹⁄” H 44 ³⁄” W x 24 ⁷⁄” H x 11 ¹⁄” D 44 ³⁄” W x 25 ¹⁄” H x 12” D

LPM-5616 54” W x 15 ¹⁄” H 56 ³⁄” W x 24 ⁷⁄” H x 11 ¹⁄” D 56 ³⁄” W x 25 ¹⁄” H x 12” D

LPM-6816 66” W x 15 ¹⁄” H 68 ³⁄” W x 24 ⁷⁄” H x 11 ¹⁄” D 68 ³⁄” W x 25 ¹⁄” H x 12” D

LPM-8016 78” W x 15 ¹⁄” H 80 ³⁄” W x 24 ⁷⁄” H x 11 ¹⁄” D 80 ³⁄” W x 25 ¹⁄” H x 12” D

LPM-9616 94" W x 15 ¹⁄" H 96 ³⁄" W x 24 ⁷⁄" H x 11 ¹⁄" D 96 ³⁄" W x 25 ¹⁄" H x 12" D

24 ⁷⁄”

(all models)

Width varies (see chart below) 11 ¹⁄”

(all models)

Drywall stops Drywall stops

INSTALLATION

BOX CONTENTS

1 Fire Unit 1 Remote

L-Metal Mounting

Brackets

2 Side Glass Pieces

2 Side Covers

1 Front Glass

Clear Acrylic Stones

Canyon Driftwood

Logs

2 Suction Cups

Smoke Acrylic

Crystals

1 Owner's Manual

INSTALLATION

WARNING: If the information in these

instructions is not followed exactly, a ﬁre

or explosion may result causing property

damage, personal injury or death.

WARNING - RISK OF FIRE!

To prevent a possible ﬁre, do not block air

intake or exhaust in any manner. Do not

use on soft surfaces where openings may

become blocked.

WARNING - RISK OF FIRE!

Do not blow or place insulation against the

ﬁrebox.

To reduce the risk of ﬁre do not store or

use gasoline or other ﬂammable vapors in

the vicinity of this or any other heater.

CAUTION: Keep combustible materials,

such as furniture, pillows, bedding,

papers, clothes and curtains at least 3

feet (0.9m) from the front of the heater and

keep them away from the sides and rear.

CAUTION: Wear gloves and safety glasses

for protection during installation and

maintenance.

Installing ﬁreplace

Select a suitable location that is not susceptible

to moisture and is a safe distance from drapes,

furniture and high traﬃc areas. A qualiﬁed

electrician should add a dedicated ﬂexible

20 amp 120 volt circuit per local building

codes. Run a second line for optional

10,000 BTU operation.

Note: Follow all national and local electrical

codes.

This ﬁreplace has a number of installation options. It can be installed fully recessed, half recessed, wall

mounted with a ﬂoating cabinet or with a simple slide-in cabinet. In addition, the fully recessed option can

be installed with all sides showing, 1 side showing, or ﬂush.

To prepare for installation, connect the hard wire to the terminal block according to the diagram below.

Choose any connector type according to local building code.

To be performed by a qualiﬁed electrician

according to local building codes.

L1 - Line 1 (primary)

L2 - Line 2 (optional)

- Ground

N - Neutral

INSTALLATION

Model W H D

LPM-4416 44 ³⁄” 25 ¹⁄” 12”

LPM-5616 56 ³⁄” 25 ¹⁄” 12”

LPM-6816 68 ³⁄” 25 ¹⁄” 12”

LPM-8016 80 ³⁄” 25 ¹⁄” 12”

LPM-9616 96 ³⁄" 25 ¹⁄" 12"

1. Prepare the framed opening according to the

chart above. *Provide appropriate dedicated

circuit for hardwire install at the top right of

framed opening.

2. Install L Metal Nailing Flanges.

3. Install the ﬁre unit in the framed opening with a

minimum 1 ¼ drywall screws to secure the unit.

4. Mask the exposed ﬁre unit during the

drywall process. Install drywall to the drywall

stops on the perimeter of the ﬁre box. For

more information on the drywall stops see the

Product Guide on page 4.

5. Decorate according to media installation guide

on page 10.

6. Install the side and front glass pieces according

to installation diagram on Page 11.

Framing Dimensions 3 Sided Installation (Bay)

INSTALLATION

Fully Recessed Installation (Left/Right Corner)

Fully Recessed Flush Installation (Single Sided)

1. Follow steps 1 & 2 from the 3 sided installation

instructions.

2. Remove the corresponding drywall stops

according to your installation (in the example,

the drywall stops on the left end would be

removed.)

3. Install the side glass then the corresponding

side cover according to your installation (the

side glass must be installed before the

metal side cover. See installation diagram on

Page 11.)

4. Install the ﬁre unit in the framed opening with a

minimum 1 ¼ drywall screws to secure the unit.

5. Mask the exposed ﬁre unit during the

drywall process. Install drywall to the drywall

stops on the perimeter of the ﬁre box. For

more information on the drywall stops see the

Product Guide on page 4.

6. Decorate according to media installation guide

on page 10.

7. Install the remaining side glass and front glass

according to installation diagram on Page 11.

1. Follow steps 1 & 2 from the 3 sided installation

instructions.

2. Remove the drywall stops on both sides of the

ﬁre unit.

3. Install the side glass then side covers on both

sides of the ﬁre unit (the side glass must be

installed before the metal side cover. See

installation diagram on Page 11.)

4. Install the ﬁre unit in the framed opening with a

minimum 1 ¼ drywall screws to secure the unit.

5. Mask the exposed ﬁre unit during the

drywall process. Install drywall to the drywall

stops on the perimeter of the ﬁre box. For

more information on the drywall stops see the

Product Guide on page 4.

6. Decorate according to media installation guide

on page 10.

7. Install the front glass according to installation

diagram on Page 11.

INSTALLATION

Half recessed installation

1. This installation is optimized for a 2x4 framed

wall. Prepare the framed opening according

to the height and width of the chart on page

7. *Provide appropriate dedicated circuit for

hardwire install at the top right of framed

opening.

2. Install L Metal Nailing Flanges to the top and

bottom of the ﬁre unit.

3. Install the ﬁre unit in the framed opening with a

minimum 1 ¼ drywall screws to secure the unit.

4. Firebox must be covered with material of

choice. Mask the exposed ﬁre unit during

this process. Install drywall, tile or material

of your choice to the drywall stops on the

perimeter of the ﬁre box. For more information

on the drywall stops see the Product Guide on

page 4.

5. Decorate according to media installation guide

on page 10.

6. Install the side and front glass pieces according

to installation diagram on Page 11.

INSTALLATION

Floating cabinet installation

Slide-in cabinet installation

Follow the directions included with the Floating

Cabinet Accessory Kit.

Follow the directions included with the Slide-in

Cabinet Accessory Kit.

Installing Media

1. Before installing the front glass, evenly spread

out the acrylic crystals along the ember bed.

2. Place the logs on top of the acrylic crystals.

3. The front glass can now be installed.

Special Order

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Modern Flames Kamin im Innenbereich Handbücher

Modern Flames

Modern Flames Landscape Pro Multiview Series Montageanleitung

Modern Flames

Modern Flames Landscape Pro Slim LPS-4414V2 Bedienungsanleitung

Modern Flames

Modern Flames ZCR 3824 Bedienungsanleitung

Modern Flames

Modern Flames Landscape Pro Multiview Series Bedienungsanleitung

Modern Flames

Modern Flames Landscape Pro Multi Kurzanleitung

Modern Flames

Modern Flames Landscape Pro Multi Bedienungsanleitung

Modern Flames

Modern Flames WMC LPM Series Bedienungsanleitung

Modern Flames

Modern Flames LPM-9616/INT Betriebsanleitung

Modern Flames

Modern Flames OR52-MUTLI Bedienungsanleitung

Modern Flames

Modern Flames AL 95 Bedienungsanleitung

Modern Flames

Modern Flames RS-2621-EU Bedienungsanleitung

Modern Flames

Modern Flames SPS-50B Bedienungsanleitung

Modern Flames

Modern Flames SPM-2426V2 Bedienungsanleitung

Modern Flames

Modern Flames OR30-SLIM-INT Bedienungsanleitung

Modern Flames

Modern Flames OR30-MULTI-INT Bedienungsanleitung

Modern Flames

Modern Flames OR52-SLIM Bedienungsanleitung

Modern Flames

Modern Flames LFV2-40/15-SH Montage- und Wartungsanleitung

Modern Flames

Modern Flames Redstone RS-2621-AU Bedienungsanleitung

Modern Flames

Modern Flames AL1500CLX Kurzanleitung

Modern Flames

Modern Flames AMBIANCE LINEAR 40 Originalbetriebsanleitung

Modern Flames

Modern Flames AFWS Series Kurzanleitung

Modern Flames

Modern Flames ORION OR52-MULTI Bedienungsanleitung

Modern Flames

Modern Flames Landscape Pro Slim Series Betriebsanleitung

Modern Flames

Modern Flames FusionFire 60 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung