Mohawk RJ-50-AH Series Bedienungsanleitung

READ MANUAL

THOROUGHLY BEFORE

INSTALLING,

OPERATING OR SERVICING

THIS LIFT !!

Deliver these instructions to lift

owner/user/employer along with

other instructional materials

furnished with this lift.

MOHAWK

MADE IN THE USA

PNEUMATIC/HYDRAULIC JACKING BEAM

Model RJ-50-AH-50000: Rated 50,000 Lb on 75k Lb Lifts (4 Post)

Model RJ-50-AH-37500-P: Rated 37,500 Lb on 75-100k Lb Lifts (Parallel)

Model RJ-50-AH-35000: Rated 35,000 Lb on 50k Lb Lifts (4 Post)

Model RJ-50-AH-35000-P: Rated 35,000 Lb on 50k Lb Lifts (Parallel)

Model RJ-50-AH-31500-P: Rated 31,500 Lb on 45k Lb Lifts (Parallel)

Model RJ-50-AH-28000-P: Rated 28,000 Lb on 40k Lb Lifts (Parallel)

Model RJ-50-AH-25000-P: Rated 25,000 Lb on 36-38k Lb Lifts (Parallel)

Model RJ-50-AH-24500: Rated 24,500 Lb on 35k Lb Lifts (4-Post)

Model RJ-50-AH-23000: Rated 23,000 Lb on 33k Lb Lifts (4-Post)

Model RJ-50-AH-20000: Rated 20,000 Lb on 30k Lb Lifts (4-Post)

INSTALLATION

OPERATION

MAINTENANCE

PARTS

MOHAWK RESOURCES LTD.

PO BOX 110, 65 VROOMAN AVE.

AMSTERDAM, NY 12010

TOLL FREE: 1-800-833-2006

LOCAL: 1-518-842-1431

FAX: 1-518-842-1289

INTERNET: WWW.MOHAWKLIFTS.COM

E-MAIL: [email protected]

RJ-50-AH-Series 12-1-2015.doc

Rev Date 12/1/2015

Part #601-800-390

Model RJ-50-AH Series

MOHAWK MODEL RJ-50-AH-SERIES

IMPORTANT SAFETY INSTRUCTIONS

When using your garage equipment, basic safety precautions should always be followed, including the

following:

1. Read all instructions. Before assembling unit, become familiar with part names and have a good

understanding of how this unit is to be assembled and of how individual parts operate.

2. Care must be taken as burns can occur from touching hot parts.

3. Do not operate equipment if it has been dropped or damaged - until it has been examined by a

qualified serviceman.

4. Do not let hoses come in contact with hot manifolds or moving fan blades.

5. Always unplug equipment from air supply when not in use.

6. Keep hair, loose clothing, fingers, and all parts of body away from moving parts.

7. Use only as described in this manual. Use only manufacturer’s recommended attachments.

8. ALWAYS WEAR SAFETY GLASSES. Everyday eyeglasses only have impact resistant lenses,

they are NOT safety glasses.

SAVE THESE INSTRUCTIONS

ALL MOHAWK JACKING BEAMS ARE FOR INDOOR USE UNLESS SPECIFICALLY QUALIFIED AND MODIFIED FOR A CUSTOM ENVIRONMENT.

PROPER FRAME ENGAGEMENT WITH PADS. ALL JACK BEAMS ARE DESIGNED TO LIFT STANDARD VEHICLES WITHIN THEIR RATED

CAPACITY BY THE VEHICLE FRAME. IF SUITABLE FRAME CONTACT LIFT POINTS CAN NOT BE REACHED OR ACCOMMODATED BY THE

LIFTING PADS, THE VEHICLE MUST NOT BE RAISED WITH THE LIFT. REFER TO VEHICLE MANUFACTURER LIFTING POINT SPECIFICATIONS

(AND VEHICLE LIFT POINT LABEL PER SAE J2184, VEHICLE LIFT POINTS FOR SERVICE GARAGE LIFTING).

CARE MUST BE OBSERVED WHEN REMOVING ANY HEAVY COMPONENTS FROM A VEHICLE AND THEREBY DRASTICALLY SHIFTING THE

VEHICLE CENTER OF GRAVITY (I.E. ENGINE REMOVAL, TRANSMISSION REMOVAL, ETC.). THE USE OF JACK STANDS AT THE FRONT AND

REAR ENDS OF THE VEHICLE IS HIGHLY RECOMMENDED WHEN PERFORMING THIS TYPE OF WORK.

ADAPTER USAGE AND LIMITATIONS:

THE USE OF HEIGHT ADAPTERS IS COMMON FOR MOST LIFTING SITUATIONS TO ACCOMMODATE HIGH FRAMES AND LOW OVERHANGING

BODIES OF VEHICLES.

FOR RJ-50-AH:

THESE LIFTS COME STANDARD WITH (2) 5” AND (2) 7 1/2” AND (2) 10” HEIGHT ADAPTERS.

THESE LIFTS ARE ONLY ALLOWED TO USE 2 ADAPTERS WHEN STACKED: ONE (1) 7 1/2” AND ONE (1) 10” ADAPTER, RESULTING IN 17 1/2”

MAXIMUM STACKING HEIGHT. LONGER CUSTOM SINGLE PIECE ADAPTERS ARE AVAILABLE UPON REQUEST.

THE USER SHOULD BE WARNED THAT ANY SITUATION PRODUCING AN OFF-VERTICAL SLANTING OF THE HEIGHT ADAPTERS, SUCH AS,

ECCENTRIC CORNER LOADING OF THE LIFT PAD, ETC. MUST BE AVOIDED. CUPPED OR YOKE STYLE LIFTING PADS (WHICH DO NOT RELY

ON FRICTION) ARE ALSO AVAILABLE FOR SITUATIONS INVOLVING LIFTING NON-FLAT SURFACES. CONSULT MOHAWK SERVICE

DEPARTMENT FOR CUSTOM PAD REQUESTS FOR YOU APPLICATION.

MOHAWK MODEL RJ-50-AH-SERIES

HAVE A QUESTION?

Call your local

Mohawk distributor

For parts, service and technical support.

Distributor Place Card Here

Please have this unit’s model and serial number when calling for service.

Model Number ______________________

Serial Number ______________________

OR CONTACT:

MOHAWK RESOURCES LTD.

65 Vrooman Ave.

P.O. Box 110

Amsterdam, NY 12010

Toll Free: 1-800-833-2006

Local: 1-518-842-1431

Fax: 1-518-842-1289

Internet: www.MOHAWKLIFTS.com

E-Mail: [email protected]

MOHAWK MODEL RJ-50-AH-SERIES

iii

MOHAWK WARRANTIES

EFFECTIVE DATE: 12/1/2015*

READ THIS WARRANTY IN ITS ENTIRETY

GENERAL WARRANTY INFORMATION:

MOHAWK’S OBLIGATION UNDER THIS WARRANTY IS LIMITED TO REPAIRING OR REPLACING ANY PART OR PARTS

RETURNED TO THIS FACTORY, TRANSPORTATION CHARGES PREPAID BY CUSTOMER WITH AUTHORIZED RETURN (RGA),

WHICH PROVE UPON INSPECTION TO BE DEFECTIVE AND WHICH HAVE NOT BEEN MISUSED. DAMAGE OR FAILURE TO ANY

PART DUE TO FREIGHT DAMAGE OR LACK OF REQUIRED REGULAR DOCUMENTED MAINTENANCE IS NOT COVERED UNDER

THIS WARRANTY. ALL WARRANTY CLAIMS MUST BE PERFORMED IN ACCORDANCE TO MOHAWK’S WARRANTY PARTS

RETURN POLICY (CONTACT MOHAWK’S SERVICE DEPARTMENT FOR MORE INFORMATION).

THIS WARRANTY DOES NOT COVER MIS-DIAGNOSING OF UNIT OR PARTS RETURNED THAT ARE NON-DEFECTIVE. THIS

WARRANTY DOES NOT COVER ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES INCLUDING, BUT NOT LIMITED TO, LOST

REVENUES OR BUSINESS HARM. THIS EQUIPMENT HAS BEEN DESIGNED FOR USE IN NORMAL VEHICLE MAINTENANCE

APPLICATIONS. A SPECIFIC INDIVIDUAL WARRANTY MUST BE ISSUED FOR UNITS THAT DEVIATE FROM INTENDED USAGE,

SUCH AS HIGH CYCLE USAGE IN INDUSTRIAL APPLICATIONS, OR USAGE IN EXTREMELY ABUSIVE ENVIRONMENTS.

MOHAWK RESERVES THE RIGHT TO DECLINE RESPONSIBILITY WHEN REPAIRS OR MODIFICATIONS HAVE BEEN MADE OR

ATTEMPTED BY OTHERS WITHOUT WRITTEN AUTHORIZATION FROM MOHAWK RESOURCES LTD.. THIS WARRANTY DOES

NOT COVER LABOR OR TRANSPORTATION. THIS WARRANTY DOES NOT COVER DOWNTIME EXPENSES INCURRED WHEN

UNIT IS IN REPAIR. THE LIFT MUST BE REGISTERED WITHIN 30 DAYS OF INSTALLATION BY MAILING SUPPLIED

WARRANTY REGISTRATION CARD TO MOHAWK AND MUST BE SIGNED BY A LICENSED ELECTRICIAN. THE MODEL

NUMBER AND SERIAL NUMBER OF THE EQUIPMENT MUST BE FURNISHED WITH ALL WARRANTY CLAIMS. THIS WARRANTY

STATEMENT CONTAINS THE ENTIRE AGREEMENT BETWEEN MOHAWK RESOURCES LTD. AND THE PURCHASER UNLESS

OTHERWISE SPECIFICALLY EXPRESSED IN WRITING. THIS NON-TRANSFERABLE WARRANTY APPLIES TO THE ORIGINAL

PURCHASER ONLY.

THIS WARRANTY DOES NOT COVER NORMAL SURFACE WEAR ITEMS, ITEMS SUBJECT TO ABRASION, OR ITEMS USED IN A

CORROSIVE ENVIRONMENT. SOME ITEMS ON LIFT ARE SUBJECT TO NORMAL “WEAR AND TEAR” AND ARE NOT COVERED

UNDER THIS WARRANTY.

STRUCTURAL AND MECHANICAL COMPONENTS (ALL LIFTS):

STRUCTURAL AND MECHANICAL COMPONENTS OF THIS UNIT ARE GUARANTEED FOR THE BELOW STATED TIME FRAME,

SPECIFIC TO MODEL LISTED, FROM THE DATE OF SHIPMENT FROM FACTORY, AGAINST DEFECTS IN WORKMANSHIP

AND/OR MATERIALS WHEN LIFT IS INSTALLED AND USED ACCORDING TO SPECIFICATIONS.

25-YEARS STRUCTURAL / 10 YEARS MECHANICAL: TWO-POST MODELS A-7, SYSTEM IA-10, LC-12, LMF-12, TP-

16, TP-18, TP-20, TP-26, TP-30. STRUCTURAL ITEMS COVERED INCLUDE LEG, CARRIAGE, SWING ARM AND

SLIDER WELDMENTS (EXCLUDING NORMAL WEAR AREAS AS STATED ABOVE). MECHANICAL ITEMS COVERED

INCLUDE ROLLER BEARINGS AND LIFTING CHAIN.

5-YEAR: MODELS TL-7.

3-YEAR: MODELS TR-19, TR-25, FL-25, TR-30, TR-33, TR-35, TR-50, TR-75, TR-110, TR-120, MP-SERIES LIFTS.

2-YEAR: MODELS PARALLELOGRAM SERIES LIFTS.

1-YEAR: MODELS TD-1000, TD-2000, CT-1000, USL-6000.

POWER UNIT (ALL LIFTS):

ALL POWER UNIT COMPONENTS (MOTOR, PUMP AND RESERVOIR) ARE GUARANTEED FOR TWO YEARS FOR PARTS,

FROM THE DATE OF SHIPMENT FROM FACTORY, AGAINST DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN THE

LIFT IS INSTALLED, WIRED BY A LICENSED ELECTRICIAN AND USED ACCORDING TO SPECIFICATIONS.

ELECTRICAL COMPONENTS (ALL LIFTS):

ALL ELECTRICAL COMPONENTS (EXCLUDING MOTOR) ARE GUARANTEED FOR ONE YEAR FOR PARTS, FROM THE DATE

OF SHIPMENT FROM FACTORY, AGAINST DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN THE LIFT IS

INSTALLED AND USED ACCORDING TO SPECIFICATIONS. SEE WARRANTY EXCEPTIONS SECTION FOR BATTERIES.

PNEUMATIC-AIR COMPONENTS (ALL LIFTS):

ALL PNEUMATIC (AIR) COMPONENTS (I.E. AIR CYLINDERS AND POPPET AIR VALVES) ARE GUARANTEED FOR ONE YEAR

FOR PARTS, FROM THE DATE OF SHIPMENT FROM FACTORY, AGAINST DEFECTS IN WORKMANSHIP AND/OR

MATERIALS WHEN THE LIFT IS INSTALLED AND USED ACCORDING TO SPECIFICATIONS. COMPONENTS IN A PNEUMATIC

SYSTEM THAT ARE NOT PROPERLY REGULATED, LUBRICATED AND CONDITIONED WITH AN AIR DRYING SYSTEM ARE

NOT COVERED UNDER WARRANTY.

HYDRAULIC COMPONENTS (ALL LIFTS):

EXCLUDING CYLINDERS AND PUMPS (COVERED IN OTHER SECTIONS), ALL HYDRAULIC COMPONENTS (I.E. VALVES AND

FITTINGS) ARE GUARANTEED FOR ONE YEAR FOR PARTS, FROM THE DATE OF SHIPMENT FROM FACTORY, AGAINST

DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN THE LIFT IS INSTALLED AND USED ACCORDING TO

SPECIFICATIONS.

MOHAWK MODEL RJ-50-AH-SERIES

HYDRAULIC CYLINDERS (MODEL SPECIFIC LIFTS):

THE FOLLOWING MODELS ARE GUARANTEED FOR 5 YEARS (PARTS ONLY), FROM DATE OF SHIPMENT FROM FACTORY,

FOR HYDRAULIC CYLINDERS, AGAINST DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN THE LIFT IS INSTALLED

AND USED ACCORDING TO SPECIFICATIONS: TWO-POST MODELS A-7, SYSTEM IA-10, LC-12, LMF-12, TP-16, TP-18, TP-20,

TP-26, TP-30.

ALL OTHER MODELS ARE GUARANTEED FOR TWO YEARS (PARTS ONLY), FROM THE DATE OF SHIPMENT FROM

FACTORY, FOR HYDRAULIC CYLINDERS, AGAINST DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN THE LIFT IS

INSTALLED AND USED ACCORDING TO SPECIFICATIONS (EXCLUDING USL-6000, WHICH IS ONE YEAR).

THE “EXTENDED LIFETIME CYLINDER SEAL WARRANTY” (BELOW) IS APPLICABLE TO THE FOLLOWING MOHAWK LIFTS

ONLY: TWO-POST MODELS A-7, SYSTEM IA-10, LC-12, LMF-12, TP-16, TP-18, TP-20, TP-26, TP-30. SEE MOHAWK’S

“EXTENDED LIFETIME CYLINDER SEAL WARRANTY” FOR SPECIFIC WARRANTY PROVISIONS FOR HYDRAULIC

CYLINDERS.

THE “EXTENDED LIFETIME CYLINDER SEAL WARRANTY” IS AS FOLLOWS:

AS THE ORIGINAL PURCHASER OF A MOHAWK LIFT MANUFACTURED BY MOHAWK RESOURCES, LTD. YOU ARE

ENTITLED TO AN EXTENDED CYLINDER SEAL WARRANTY.

MOHAWK’S OBLIGATION UNDER THIS WARRANTY IS LIMITED TO SUPPLYING MODEL SPECIFIC CYLINDER SEALS. THE

CUSTOMER IS RESPONSIBLE FOR SHIPPING AND HANDLING OF THE SEALS. MOHAWK IS NOT RESPONSIBLE/LIABLE

FOR THE REBUILD OF CYLINDERS BY OTHERS. THIS WARRANTY IS NON-TRANSFERABLE AND RUNS TO THE ORIGINAL

PURCHASER ONLY.

STANDARD OPTIONS (ALL LIFTS):

ALL STANDARD OPTIONS OF THIS UNIT ARE GUARANTEED FOR ONE YEAR FOR PARTS, FROM THE DATE OF SHIPMENT

FROM FACTORY, AGAINST DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN LIFT IS INSTALLED AND USED

ACCORDING TO SPECIFICATIONS.

CUSTOM LIFTS AND CUSTOM OPTIONS:

ALL “CUSTOM” LIFTS AND/OR “CUSTOM” OPTIONS ARE GUARANTEED FOR ONE YEAR FOR PARTS, FROM THE DATE OF

SHIPMENT FROM FACTORY, AGAINST DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN LIFT IS INSTALLED AND

USED ACCORDING TO SPECIFICATIONS.

WARRANTY EXCEPTIONS (ALL LIFTS):

ADJUSTMENTS: THIS WARRANTY DOES NOT COVER CASUAL AND ROUTINE ADJUSTMENTS SUCH AS, BUT NOT LIMITED

TO: FITTINGS, SENSORS AND SWITCHES, ANCHOR BOLT RE-TIGHTENING, OR ANY SHIMMING OR ADJUSTMENTS

REQUIRED DURING A PROPER AND PROFESSIONAL INSTALLATION BY A QUALIFIED INSTALLER.

MAINTENANCE AND INSPECTIONS: IF THIS UNIT IS NOT MAINTAINED AND INSPECTED IN ACCORDANCE TO THE

RELEVANT SECTIONS IN THE USERS MANUAL FOR THIS SPECIFIC MODEL, WARRANTY IS VOID. OSHA, ANSI AND

MOHAWK REQUIRE THAT RECORDS MUST BE MAINTAINED TO PROVE THAT INSPECTIONS AND MAINTENANCE OF THIS

UNIT HAVE BEEN ROUTINELY PERFORMED BY QUALIFIED INDIVIDUALS.

ABUSE: IF THIS UNIT IS FOUND TO BE OVERLOADED (PURPOSELY OR UNKNOWINGLY), USED IN A SITUATION BEYOND

ITS INTENDED FUNCTION, NOT MAINTAINED & INSPECTED REGULARLY, USED IN AN ABUSIVE ENVIRONMENT OR

BEYOND NORMAL SHOP USAGE, THIS WARRANTY IS VOID IN ITS ENTIRETY.

NON-EXISTENT PROBLEMS: FOR SERVICE VISITS, PART REPLACEMENTS, LABOR, ETC. FOR PARTS FOUND TO BE NON-

DEFECTIVE, OR FOR A UNIT DIS-FUNCTION THAT DOES NOT EXIST, IT IS THE LIFT OWNER THAT REQUESTED THE

SERVICE VISIT WHO BEARS THE RESPONSIBILITY OF ALL RELATED EXPENSES.

BATTERIES: ALL BATTERIES CARRY THE BATTERY MANUFACTURER’S WARRANTY. MAINTENANCE REQUIREMENTS AND

ABUSE PROVISIONS ARE AS STATED BY THE BATTERY MANUFACTURER. REFER TO BATTERY MANUFACTURER’S

WARRANTY.

SPECIAL/MODIFIED INSTALLATIONS: THIS WARRANTY DOES NOT COVER “NON-TRADITIONAL” INSTALLATIONS.

INSTALLATIONS ARE TO BE DONE ACCORDING TO SPECIFICATIONS, OR THE WARRANTY IS VOID.

WEARABLE COMPONENTS: SOME ITEMS ON LIFTS ARE SUBJECT TO NORMAL “WEAR AND TEAR” AND ARE NOT

COVERED UNDER THIS WARRANTY.

NON-VEHICLE / RE-PURPOSED LIFTS: THIS WARRANTY DOES NOT COVER LIFTS THAT ARE “RE-PURPOSED” TO RAISE

AND LOWER EQUIPMENT THAT ARE NOT CONSIDERED VEHICLES.

* THIS WARRANTY SUPERSEDES ALL OTHER WARRANTY POLICIES PREVIOUSLY STATED AND IN ALL OTHER MOHAWK

PRODUCT SPECIFIC LITERATURE (MANUALS, BROCHURES, ETC.).

Rev 12/1/2015

MOHAWK MODEL RJ-50-AH-SERIES

CONTENTS

TEXT

PAGE

IMPORTANT NOTES 2

SPECIFICATIONS 3

PACKINGLIST 4

INSTALLATION INSTRUCTIONS 5

SAFETY TIPS 6

PRE - OPERATION CHECK LIST / LIFTING PROCEDURES 7

MAINTENANCE PROCEDURES 8

TROUBLE SHOOTING 9

SERVICECHART 10

MAINTENANCE CHART 10

PARTS & DIAGRAMS

FIGURE PAGE

RJ-50-AH-SERIES SPECIFICATION DRAWING FOR TR-30 025-050-046 12

RJ-50-AH-SERIES SPECIFICATION DRAWING FOR PARALLELOGRAM 025-050-047 13

RJ-50-AH-SERIES SPECIFICATION DRAWING FOR TR-33 THRU TR-75 025-050-048 14

RJ-50-AH ASSEMBLY FOR TR-33 THRU TR-75 050-050-090 15

RJ-50-AH ASSEMBLY FOR PARALLELOGRAM 050-050-094 16

RJ-50-AH DECALS 050-050-088 17

RJ-50-AH CENTER ASSEMBLY 050-050-091 18-22

CYLINDER ASSEMBLY 025-050-071 23

SCISSOR ARM ASSEMBLY 025-050-072 24

SLIDER ARM ASSEMBLY 025-050-043 25

HYDRAULIC SCHEMATIC 050-050-069 26

ALI WARNING, CAUTION AND SAFETY MESSAGES 27

ALL INFORMATION, ILLUSTRATIONS, AND SPECIFICATIONS IN THIS MANUAL ARE BASED ON THE LATEST PRODUCT INFORMATION

AVAILABLE AT THE TIME OF PRINTING. WE RESERVE THE RIGHT TO MAKE CHANGES AT ANY TIME WITHOUT NOTICE.

MOHAWK MODEL RJ-50-AH-SERIES

IMPORTANT NOTES FOR MOHAWK LIFT DEVICES

RECOMMENDATIONS BY THE INDIVIDUAL USER OR USING

ORGANIZATION FOR IMPROVING THIS PUBLICATION OR ANY

ASPECT OF THE PRODUCT ARE ENCOURAGED AND SHOULD BE

FORWARDED IN WRITING TO:

MOHAWK RESOURCES LTD.

PRODUCT IMPROVEMENTS

65 VROOMAN AVE.

AMSTERDAM, NY, 12010

THIS IS NOT A VEHICLE LIFTING PROCEDURE MANUAL AND NO

ATTEMPT IS MADE OR IMPLIED HEREIN TO INSTRUCT THE USER

IN LIFTING METHODS PARTICULARLY TO THE INDIVIDUAL

APPLICATION OF THE EQUIPMENT DESCRIBED IN THIS MANUAL.

RATHER, THE CONTENTS OF THIS MANUAL ARE INTENDED AS A

BASE LINE FOR OPERATION, MAINTENANCE, TROUBLE

SHOOTING, AND PARTS LISTING OF THE UNIT AS IT STANDS

ALONE AND AS IT IS INTENDED AND ANTICIPATED TO BE USED

IN CONJUNCTION WITH OTHER EQUIPMENT.

PROPER APPLICATION OF THE EQUIPMENT DESCRIBED HEREIN

IS LIMITED TO THE PARAMETERS DETAILED IN THE

SPECIFICATIONS AND THE USES SET FORTH IN THE

DESCRIPTIVE PASSAGES. ANY OTHER PROPOSED APPLICATION

OF THIS EQUIPMENT SHOULD BE DOCUMENTED AND

SUBMITTED IN WRITING TO MOHAWK RESOURCES LTD. FOR

EXAMINATION. THE USER ASSUMES FULL RESPONSIBILITY FOR

ANY EQUIPMENT DAMAGE, PERSONAL INJURY, OR ALTERATION

OF THE EQUIPMENT DESCRIBED IN THIS MANUAL OR ANY

SUBSEQUENT DAMAGES.

DO NOT WELD, APPLY HEAT, OR MODIFY THIS EQUIPMENT IN ANY

MANNER WITHOUT WRITTEN AUTHORIZATION FROM MOHAWK

RESOURCES LTD. CERTAIN ALLOY OR HEAT-TREATED

COMPONENTS MAY BE DISTORTED OR WEAKENED, RESULTING IN

AN UNSAFE CONDITION.

MOHAWK RESOURCES LTD. IS NOT RESPONSIBLE FOR

DISTORTIONS, WHICH RESULT FROM WELDING ON THIS

EQUIPMENT AFTER MANUFACTURING IS COMPLETED.

UNAUTHORIZED WELDING, APPLICATION OF HEAT, OR

MODIFICATION OF THIS EQUIPMENT VOIDS ANY AND / OR ALL

APPLICABLE WARRANTIES COVERING THIS EQUIPMENT.

ALL WARRANTIES APPLICABLE TO THIS EQUIPMENT ARE

CONTINGENT ON STRICT ADHERENCE TO THE MAINTENANCE

SCHEDULES AND PROCEDURES IN THIS MANUAL.

KEEP ALL SHIELDS AND GUARDS IN PLACE. INSURE ALL SAFETY

MECHANISMS ARE OPERABLE. KEEP HANDS, FEET, AND

CLOTHING AWAY FROM POWER-DRIVEN AND MOVING PARTS.

CAUTION

THE EQUIPMENT DESCRIBED IN THIS MANUAL COULD BE

POTENTIALLY DANGEROUS IF IMPROPERLY OR CARELESSLY

OPERATED. FOR THE PROTECTION OF ALL PERSONS AND

EQUIPMENT, ONLY COMPETENTLY TRAINED OPERATORS WHO

ARE CRITICALLY AWARE OF THE PROPER OPERATING

PROCEDURES, POTENTIAL DANGERS, AND SPECIFIC

APPLICATION OF THIS EQUIPMENT SHOULD BE ALLOWED TO

TOUCH THE CONTROLS AT ANY TIME.

SAFE OPERATION OF THIS EQUIPMENT IS DEPENDENT ON USE,

IN COMPLIANCE WITH THE OPERATION PROCEDURES OUTLINED

IN THIS MANUAL ALONG WITH THE MAINTENANCE AND

INSPECTION PROCEDURES WITH CONSIDERATION OF

PREVAILING CONDITIONS.

THE EQUIPMENT DESCRIBED IN THIS MANUAL IS NEITHER

DESIGNED NOR INTENDED FOR ANY APPLICATION ALONE OR IN

CONJUNCTION WITH ANY OTHER EQUIPMENT THAT INVOLVES

THE LIFTING OR MOVING OF PERSONS.

ALWAYS CONSULT THE VEHICLE LIFTING GUIDE FOR THE

PROPER LIFTING POINTS ON ANY VEHICLE. THESE GUIDES ARE

AVAILABLE FROM THE VEHICLE MANUFACTURERS.

AFTER LIFTING THE VEHICLE TO THE DESIRED HEIGHT,

ALWAYS LOWER THE UNIT ONTO THE MECHANICAL SAFETIES.

THE FORMING OF GOOD OPERATIONAL WORK HABITS WILL

ELIMINATE OVERSIGHTS IN THE USE OF PROVIDED SAFETY

DEVICES.

RJ-50-AH-SERIES JACKING BEAMS:

Only certified RJ-50-AH-Series Jacking Beams are intended for use on certified versions of the Mohawk

Parallelogram Lifts (see list below). Follow load rating of beam dependant on what lift it is on. Use of non-

certified jacking beams on certified lifts will void the certification of the lift.

RJ-50P-Series Jacking Beams for use on the following certified lifts: