MoJack EZ Einrichtungshandbuch

EZ Repair Instructions

Damaged Bronze Nut

If additional help is needed, please call MoJack Customer Service: 1-877-575-3173.

Review the Product Manual and Parts List for MoJack EZ at www.themojack.com. The detailed breakout

drawing includes all part numbers used in these instructions.

DO NOT attempt any repairs on your MoJack if there is a mower on the lift.

PROBLEM: Damaged Bronze Nut

Probable

cause: Excessive load (maximum lifting capacity for MoJack EZ is 300 lbs.) bent Lift Screw or

damaged thread on lift screw.

Solution: Replace Bronze Nut (Carrier) #28

Tools needed:

•Hammer

•Small 1/8 pin punch

•Large 5/16 pin punch

•Two 19mm wrenches or two adjustable wrenches

Steps to make the repair:

Place the MoJack EZ lift on its side and position Crank Handle

#4 so that it cannot move.

•Using a small punch, tap all parts of the existing Roll Pin #32

out of the hole at the bottom of the Lift Screw #1.

•DO NOT try to drill out a broken Roll Pin as it may cause

damage to the hole.

•Remove Flat Washer #27 from Lift Screw.

Unscrew the Lift Screw out of the Bronze Nut #28 in the Carrier

Assembly #30, by turning the Crank Handle counter-clockwise.

EZ Repair Instructions

Damaged Bronze Nut

If additional help is needed, please call MoJack Customer Service: 1-877-575-3173.

Now that the Lift screw has been removed from the Carrier

Assembly, remove Carrier Bolt #2 (using two 19mm wrenches)

and Rear Carriage Roller #31 which will allow

you to take the Carrier Assembly off of the Tower #40.

•This may require pulling out the Carrier Locking Pin #33 if it

is engaged in one of the locking holes in the Tower.

Remove carrier bolt and roller 

Take off carrier assembly 

•You now have access to the damaged Bronze Nut which will

slide out.

•Place the new part on the slots.

•There is no front or back to the Bronze Nut and it does not

matter which end is up.

Install the Carrier Assembly back on the Tower with the Carrier

Bolt and Rear Carriage Roller.

•Caution: do not over-tighten the Carrier Bolt as the Rear

Roller needs to turn freely.

EZ Repair Instructions

Damaged Bronze Nut

If additional help is needed, please call MoJack Customer Service: 1-877-575-3173.

Make sure the two Front Carriage Rollers #29 are in place

below the new Bronze Nut and to the left and right side.

•Thread the Lift Screw down from the top into the new Bronze

Nut by rotating the Crank Handle clockwise.

•The two Front Carriage Rollers should be on the left and

right of the Lift Screw as it passes below the Bronze Nut.

•Continue rotating until the Lift Screw goes through the

welded tab at the bottom of the Tower.

Apply new Flat Washer on Lift Screw and hammer the new Roll

Pin (bevel end first) into the hole using a large punch.

EZ Repair Instructions

Damaged Bronze Nut

If additional help is needed, please call MoJack Customer Service: 1-877-575-3173.

10)

•Grease (or oil) top and bottom of new Flat Washer and the

new Lift Screw.

•This might be a good time to do the yearly maintenance on

your MoJack EZ. Consult your Product Manual, page 17,

for the Maintenance Schedule

11)

Before attempting to load your mower, test raising and lowering

the Lift Arm to make sure your MoJack EZ is working properly.

Andere Handbücher für EZ

Inhaltsverzeichnis

Andere MoJack Hebesystem Handbücher

MoJack

MoJack ZR 350 Bedienungsanleitung

MoJack

MoJack EZ Montageanleitung

MoJack

MoJack MoJackPRO Montageanleitung

MoJack

MoJack EZ Einrichtungshandbuch

MoJack

MoJack EZ Lift Montageanleitung

MoJack

MoJack XT Montageanleitung

MoJack

MoJack WorkBench Montageanleitung

MoJack

MoJack PRO Montageanleitung

MoJack

MoJack HDL 45501 Montageanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung