Molpir CommandCall CC2 Leitfaden

CommandCall

CC2

GSM communication module

User

Installations Manual

Order Number

20630032270

SW version 3.19 & 3.20

Dear user, many thanks for choosing CommandCall CC2 unit. We believe this unit will fulfil your needs and

expectations.

Please leave ComamndCall installation into the vehicle to authorised Installation Centre as it must be

connected with other equipment of the vehicle (independent heater, alarm, ...).

GSM communication module CommandCall CC2 can be used in any type of vehicle due to its voltage auto

sensing feature (auto sensing 12 / 24V).

Integrated quad band GSM module Siemens enables CommandCall to work in all GSM networks. For user

comfort it is possible to use temperature values either in degrees Celsius or Fahrenheit.

This manual describes step by step functions of GSM communications module CommandCall CC2 in point

of view of the user - describes the format of SMS control commands, behaviour of the device and reports

sent to the user, unit controls via phone call with tone dial functions, control via in the vehicle installed

ON/OFF push button and control by external clock.

Installation and work with PC Setup program used for initial CommandCall CC2 setup, unit installation in

the vehicle and its initialisation are described in separate Installations Manual.

Basic commands overview is helpful tool for the heater control in form of credit card which can be kept by

the user all the time ready to use.

this sign shows important warnings and remarks in this manual, please pay adequate

attention to them.

Before installing new SIM card into CommandCall control unit setup SIM card PIN to 0000

(default SIM PIN set during HW production). In the case you would like to have other SIM PIN

than 0000 such SIM PIN code must be written to CommandCall unit before its installation to the

vehicle by PC Setup !

By typing wrong SIM PIN code in the CommandCall PC Setup programme the SIM card

will be blocked (system tries to register to GSM network repeatedly and will use all 3

allowed attempts to give correct PIN code of the SIM card).

It is possible to use SIM card with disabled PIN code. In such case is SIM PIN code written to

CommandCall unit ignored.

SMS commands sent from free SMS gates of internet providers may be in some cases ignored

(SMS commands starting with text information are intentionally ignored, because the format of

SMS command is fixed and all SMS commands must start with number).

SMS reports are a kind of a feed back information on heater operation so it is important to

enable sending at least SMS reports when heater/ventilation is switched ON.

Contents

1. General description .................................................... 3

2. Unit control .................................................... 4

2.1. Switching ON the heater by phone call ringing .................................................... 4

2.2. Control via SMS commands - basic functions .................................................... 5

2.2.1. switch OFF heater / ventilation .................................................... 5

2.2.2. switch ON the heater for preset time .................................................... 5

2.2.3. switch ON the ventilation for preset time .................................................... 6

2.2.4. check current status of the device (status SMS) .................................................... 6

2.2.5. switch ON heater / ventilation for given time .................................................... 7

2.2.6. change of the length of preset heater / ventilation ON time ........................................... 7

2.3. Heater control by phone call with tone dial .................................................... 7

2.4. Heater control by ON/OFF push button .................................................... 8

2.5. Heater control by external clock .................................................... 9

2.6. Parameters set up .................................................... 9

2.6.1. one parameter / phone number / checkbox setting or modification ................................... 10

2.6.2. all VIP phone numbers setting .................................................... 10

2.6.3. all single checkboxes setting .................................................... 11

2.6.4. all triple checkboxes setting .................................................... 11

2.6.5. all parameters setting .................................................... 11

2.6.6. password setting .................................................... 12

2.7. Checkboxes .................................................... 12

2.8. Basic commands memo card .................................................... 14

3. Supplementary functions .................................................... 14

3.1. System reset .................................................... 14

3.2. Power cut / backup battery .................................................... 14

3.3. Alarm states processing .................................................... 15

3.4. Indication of reaching limit temperatures .................................................... 17

3.5. Thermostat - automatic temperature control within preset temperature interval.................. 17

3.6. Indication of car battery voltage decrease under preset limit .................................................... 18

3.7. Periodical connectivity test .................................................... 18

3.8. Optional outputs activation .................................................... 19

3.9. Short circuit .................................................... 19

4. Appendixes .................................................... 19

4.1. Status SMS structure .................................................... 19

4.2. Trouble shooting .................................................... 20

4.3. Technical specification .................................................... 21

1. General description

GSM communication module CommandCall CC2

is used for transfer of control commands and reports

between the user and the vehicle via SMS in GSM network and via phone calls with tone dial function to

control connected device (independent heater) via control signals 300 mA.

CommandCall CC2 enables:

•control and monitoring of the status of independent heater in vehicle via SMS commands and reports

and by phone call with tone dial function

•to switch ON the heater (ventilation) by phone call ringing without establishing full connection - this

requires no charges from network operator

•to switch ON the heater (ventilation) and to switch it OFF by ON/OFF push button with LED indication

in the vehicle

•to toggle heater / ventilation mode by ON/OFF push button with LED indication in the vehicle

•to activate / deactivate external clock (e.g. if control signals of external clock are accepted or not by

main control unit)

•voice messages language selection for heater/ventilation control by phone call with tone dial function

(14 languages available)

•to measure actual in car temperature with indication of reaching preset limit values

•automatic temperature control within temperature interval (thermostat)

•to measure actual voltage of vehicle battery with indication of its decrease below preset limit value

•paging of car alarm and external device alarm status information with possibility to handle alarm states

independently or as logically related

•activation / deactivation of optional outputs +300 mA and -300 mA (simultaneous activation /

deactivation)

Integrated part of the CommandCall

is built in GSM module (phone) supporting any GSM mobile operator

at 850/900/1800/1900 MHz. In the system may be used any post-paid or prepaid SIM card. In the case of

using prepaid SIM card it is important to watch SIM card validity (expiration) and keeping necessary credit

available on the card to be sure the system is ready to send SMS report to the user when needed. Some

mobile operators offer the feature of automatic maintenance of minimal credit.

Enabling / disabling functions of the system is done by activation/deactivating relevant checkbox (sending

SMS related to execution of specific function, activation/deactivation of selected function, selection to show

temperature in °C or °F, ...).

CommandCall CC2 memory can store up to 6 so called VIP phone numbers with granted special rights for

system control. VIP users can switch heater/ventilation by phone call ringing and they do not need to use

password in SMS commands or in tone dial phone call. It is possible to allow all other users to send SMS

commands without a password too (password disable function).

2. Unit control

The user communicates with in the car installed unit via sending and receiving SMS, by making phone call

with tone dial function or directly by ON/OFF push button in the vehicle. All mentioned ways of control is

possible to combine. Control signals of external clock can be override by SMS commands, by phone call

commands or by ON/OFF push button operation. It means if heater was switched ON by external clock

then SMS command “0” or pressing ON/OFF push button will switch OFF the heater.

Format of sent commands is fixed, the format (text) of SMS reports which CommandCall sends to the user

may be set during the unit installation. All parameters except PIN code of SIM card may be changed / set

during standard operation by specific SMS command.

Control by phone call is done through 2 way communication, when CommandCall CC2 delivers voice

messages to the user and accepts user’s commands given by pressing phone buttons during phone call.

Communication can be in preset language from 14 languages available (English, German, Slovak, Czech,

Swedish, Norwegian, Polish, French, Russian, Hungarian, Finish, Danish, Italian and Spanish).

It is important to activate only those checkboxes which reports are necessary for proper user information

and correct operation of the unit especially for giving feedback information to user when switching ON the

heater. Keep in mind, please, that sending SMS reports is charged according to used prepaid or post-paid

program of respective GSM network operator.

2.1. Switching ON the heater by phone call ringing

This function is available only for calls made from phone numbers listed among VIP phone numbers and

when checkbox No.25 - “Enable heater/ventilation ON by phone call ringing” is activated.

Incoming phone call will be handled as follows:

a. phone call is possible to cancel by user within 10 seconds from it start (before the third ring) and in

such case nothing happens. Incoming phone call is not indicated in the vehicle and pressing ON/OFF

push button has no influence on phone call handling.

b. after 10 seconds is phone call from phone number listed among VIP numbers rejected by the system

and is processed as command to switch ON heater (ventilation) for time equal to HTP parameter value.

If checkbox No.5 (9) is activated then SMS report “Heater ON by phone call ringing” or SMS

“Ventilation ON by phone call ringing” is sent to the caller phone.

c. if heater or ventilation is already ON when the phone call is ringing then incoming phone call is

accepted and handled in mode of phone call with tone dial function regardless it is VIP or normal phone

number.

d. every phone call made from the phone number which is not listed among VIP phone numbers is

accepted immediately and handled in mode of phone call with tone dial functions regardless heater

(ventilation) is ON or OFF.

e. if checkbox No.25 is not activated then every phone call is accepted immediately and handled in mode

of phone call with tone dial functions regardless it is made by VIP or non VIP phone number and

regardless heater (ventilation) is ON or OFF.

f. after HTP minutes expiration heater (ventilation) is automatically switch OFF.

In the case of switching ON the heater (ventilation) by phone call ringing no real phone

connection is established and thus no fees are applicable / paid to mobile operator.

2.2. Control via SMS commands - basic functions

Format of SMS commands is fixed in form: „password“ „command code“ „command parameter“, while

„password“ consist of 4 digits (must contain 4 digits)

„command code“ consist of one to three digits

„command parameter“ is specific for each command and can contain phone number, time

information, requested temperature value, ...

Commands code with leading zero(s) may be used in short version, e.g. with leading

zero(s) omitted. For example the command „003“ can be used in short version as „3“.

There is no separator in between the password and command code (space, comma, ...). Between

command code and command parameter is used separator “-“ and between respective parameters is used

comma as a separator.

User password is factory set to the value 1234. By SMS command “781” is possible to disable using user

password in the system and then all SMS commands starts directly with the command code (in such case

the password is not used at all). User password is possible to change any time by using SMS command

„781“. Users listed in VIP phone numbers list do not use password in SMS commands even when

password is requested from other users.

Execution and confirmation of individual command can be delayed depending on actual

traffic in used GSM network.

2.2.1. Switch OFF the heater (ventilation)

SMS command in form xxxx0 (xxxx is user password) will switch OFF the heater (ventilation) and send

back to the user confirmation SMS report „Eberspaecher OFF by SMS, ± ttt.tC, vv.vV“

Confirmation SMS is sent to the user only in the case it is enabled by activating checkbox No. 1. For SMS

message construction are valid conditions



and



Remarks (conditions) for adding time, temperature and voltage values to confirmation SMS:



- remaining heating (ventilation) time is shown only in the case checkbox No. 20 is activated.



actual temperature in the vehicle is shown only in the case checkbox No. 21 is activated.



- actual car battery voltage is shown only in the case checkbox No. 22 is activated.

2.2.2. Switch ON the heating for preset time HTP minutes

SMS command in form xxxx1 (xxxx is user password) will switch ON heating for preset time HTP minutes,

sets internal mode heating/ventilation to „heating“ and sends back to the user confirmation SMS report

„Eberspaecher ON by SMS, MMM min.,± ttt.tC, vv.vV“

Confirmation SMS is sent to the user only in the case it is enabled by activating checkbox No. 4. For SMS

message construction are valid conditions



and



. The length of heating period is always shown in this

message.

After HTP minutes expiration heater is automatically switch OFF.

In the case HTP=999 then heating is switch ON for unlimited time and confirmation SMS „Heater ON

unlimited, ± ttt.tC, vv.vV“ is sent to the user. Confirmation SMS is sent to the user only in the case it is

enabled by activating checkbox No. 12. For SMS message construction are valid conditions



and



2.2.3. Switch ON ventilation for preset time HTP minutes

SMS command in form xxxx2 (xxxx is user password) will switch ON ventilation for preset time HTP

minutes, sets internal mode heater/ventilation to „ventilation“ and sends back to the user confirmation SMS

report „Ventilation ON by SMS, MMM min.,± ttt.tC, vv.vV“

Confirmation SMS is sent to the user only in the case it is enabled by activating checkbox No. 8. For SMS

message construction are valid conditions



and



. The length of ventilation period is always shown in

this message.

After HTP minutes expiration ventilation is automatically switch OFF.

In the case HTP=999 then ventilation is switch ON for unlimited time and confirmation SMS „Ventilation ON

unlimited, ± ttt.tC, vv.vV“ is sent to the user. Confirmation SMS is sent to the user only in the case it is

enabled by activating checkbox No. 13. For SMS message construction are valid conditions



and



2.2.4. Check actual status of the device

SMS command in form xxxx3 (xxxx is user password) sends back to the user Status SMS describing actual

state of the device. Status SMS consist of several information fields concatenated into one SMS message.

Structure of Status SMS is described in paragraph 4.1. Status SMS structure of this Manual.

Samples of Status SMS:

•heating was switched on by external clock, thermostat is activated (activated checkbox

No.18), actual temperature decreased below UST2 and external clock is enabled:

Heater ON by clock,

Automatic mode,

External clock enabled,

+14.5 C,

12.7 V

•ventilation is ON by ON/OFF button, thermostat control is deactivated (deactivated checkbox

No.18), actual temperature decreased below UST2 and external clock is disabled:

Ventilation ON by button,

23 min.,

+14.5 C,

12.7 V

•unit is OFF, thermostat control is activated (activated checkbox No.18), actual temperature

decreased below UST2 and external clock is disabled:

Eberspaecher OFF,

Automatic mode,

+14.5 C,

12.7 V

2.2.5. Switch ON heating / ventilation for given time (range 10 to 120 minutes or unlimited)

SMS command in form xxxxMMM (xxxx is user password) will switch ON heating or ventilation for MMM

minutes (MMM is whole positive number in range 10 to 120 or 999). Actual state of internal mode

heating/ventilation determines if „heating“ or „ventilation“ will be switched ON (if lastly was used heating or

ventilation). Confirmation SMS „Eberspaecher ON by SMS, MMM min.,± ttt.tC, vv.vV“ or „Ventilation ON by

SMS, MMM min.,± ttt.tC, vv.vV“ is sent back to the user.

Confirmation SMS is sent to the user only in the case it is enabled by activating checkbox No.4 (for heating)

or checkbox No.8 (for ventilation) . For SMS message construction are valid conditions



and



. The

length of heating / ventilation is always shown in this message regardless checkbox No.20 actual setting.

After expiration of given number of minutes heater or ventilation is automatically switched OFF.

In the case HTP=999 then heating / ventilation is switch ON for unlimited time and confirmation SMS

„Heater ON unlimited, ± ttt.tC, vv.vV“ or „Ventilation ON unlimited, ± ttt.tC, vv.vV“ is sent to the user.

Confirmation SMS is sent to the user only in the case it is enabled by activating checkbox No.12 for heating

or No.13 for ventilation. For SMS message construction are valid conditions



and



2.2.6. change of the length of preset heater / ventilation ON time

SMS command in format xxxx281-HTP=MMM (xxxx is user password) will set HTP parameter to MMM

minutes value and sends confirmation SMS “281 OK”. Confirmation SMS is sent to the user only in the

case it is enabled by activating checkbox No.17.

For example: command xxxx281-HTP=35 will set HTP value to 35 (xxxx is user password).

2.3. Heater control by phone call with tone dial functions

Control by phone call with tone dial functions is made as 2 way communication where CommandCall CC2

plays voice messages to user and accepts user commands by pressing phone buttons during phone call.

This method is used to control only basic functions of the unit:

Button Function

0 switch OFF heater / ventilation

1 switch ON heater for preset time (duration) HTP minutes

2 switch ON ventilation for preset time (duration) HTP minutes

3 request for actual status of the unit

4 activate external clock (control signals of external clock will be taken into consideration)

5 deactivate external clock (control signals of external clock are not taken into consideration)

After phone call is established system requires password from unknown phone numbers (not listed among

VIP phone numbers). When valid password is entered system announces actual status of the unit (Heater /

ventilation ON or OFF) and requests user to input command. User gives valid command by pressing some

of phone buttons 0 to 5. System acknowledges accepting of the command by voice message and requests

next command.

User has 5 seconds time limit to input command (to press button). In the case user will press no

button within time limit system requests command input again. If user input no command even

after the third request phone call is terminated.

Pressing any other button than 0, 1 to 5 is evaluated as invalid command and system requests to

input command again. If user inputs 3 times invalid command in the sequence then phone call is

terminated.

In the case checkbox No.24 is activated and during phone call was given command „3“ then

immediately after phone call termination Status SMS will be sent to the user (caller phone).

Communication (playing voice messages) can be selected in one from 14 languages. Language selection

which will be used for voice messages (parameter LANG) can be done by SMS command 281:

xxxx281-LANG=LL, xxxx is user password and LL is positive whole number in range 1 to 14.

(1 = English, 2 = German, 3 = Slovak, 4 = Czech, 5 = Swedish, 6 = Norwegian, 7 = Polish, 8 = French, 9 =

Russian, 10 = Hungarian, 11 = Finish, 12 = Danish, 13 = Italian, 14 = Spanish).

2.4. Heater control by ON/OFF push button with LED indication (orange LED)

Heater/ventilation is possible to control by ON/OFF push button installed in the vehicle:

Function Description Status indications / SMS

Switch

heater ON Short pressing of the push button (max. 1 second).

The heater will be ON depending on parameter HTP

preset time in the range of 1 to 120 minutes or

unlimited in the case HTP=999.

If checkbox No.7 is activated then SMS “Heater ON by

switch, MMM min., ±ttt.t C, vv.v V“ is sent to the first

VIP phone number.

After button release LED will lit ON

indicating heater status „ON“.

Switch

ventilation

The same as for heating but LED will flash.

If checkbox No.11 is activated then SMS “Ventilation

ON by switch, MMM min.,

±ttt.t C, vv.v V“

is sent to the

first VIP phone number.

After button release LED will flash

indicating ventilation status „ON“.

Switch

heater OFF

Short pressing of the push button (max. 1 second)

when heater/ventilation is ON.

If checkbox No.3 is activated then SMS “Eberspaecher

OFF by switch,

±ttt.t C, vv.v V“

is sent to the first VIP

phone number.

After button release LED will

switch OFF indicating status „OFF“

Heater /

ventilation

mode

change

Pressing of the push button for 5 seconds will toggle

heater/ventilation mode. After 5 seconds LED will start

to indicate actual mode - when entering heater mode

LED will lit 5 seconds while when entering ventilation

mode LED will quickly flash for 5 seconds. When this

indication starts release the push button to accept

mode change.

Note: heater/ventilation mode change perform only

when heater/ventilation is OFF, otherwise LED

indication can not be seen correctly.

After 5 seconds LED will start

indication of mode change.

Indication of entered mode lasts 5

seconds, during this period release

the button to accept mode change.

Then system indicates new mode

by 5 seconds lit for heater mode or

5 seconds flashing for ventilation

mode.

System

RESET Pressing of the push button for at least 40 seconds will

reset the system.

System RESET will restart CommandCall control unit,

will restart GSM module, resets outputs overload

protection circuits and clears internal counters.

System RESET will not change checkboxes

settings or preset values (UST, TS, ..., timer preset).

After 5 seconds LED will flash 5

times - please keep push button

pressed. When the time 40 sec. is

reached LED will flash 4 times -

release the push button now.

After release of push button LED

will lit 2 sec. to indicate RESET

Backup

battery cut

OFF

Press and hold the push button for at least 20 seconds

when the power is OFF, this will cut OFF

CommandCall backup battery

After cutting off backup battery all

LEDs will switch OFF

Note: Status will be changed after button is released (system reacts on signal „fall down edge“).

Andere Handbücher für CommandCall CC2

Inhaltsverzeichnis

Andere Molpir Steuereinheit Handbücher

Molpir

Molpir CommandCall CC2 Leitfaden

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung