MODEL 306 DUAL CHANNEL DATALOGGING THERMOMETER
3
4.0 Operating Instructions:
4.1 Preparation for Measurement
Plug the first thermocouple into the socket marked T1, taking care to observe the polarity
of the thermocouple pins. If dual sensors are being used, plug the second thermocouple
into the socket marked T2.
4.2 Power
Press the button to turn the thermometer ON or OFF.
When first powered on, the LCD will show how much memory
space is available for use.
Example: Display at right indicates 16,000 records of available
memory.
4.3 Selecting the Temperature Scale
When first turned on, the instrument defaults to reading in Celsius (°C). The instrument
toggles between Celsius (°C) and Fahrenheit (°F) each time the °C/°F button is pressed.
The instrument remembers the scale setting when last turned off and powers on in that
setting the next time.
4.4 Data-Hold Function
The present reading is held on the display by pressing the HOLD button. Pressing the
HOLD button again releases the hold function and returns the instrument to
continuous reading.
In the HOLD mode, the TIME, MAX MIN and °C/°F buttons are disabled, as indicated by
two consecutive beeps when pressed.
4.5 Clock Setup
To set the real time clock:
1. Press and hold the MAX MIN button and then power on
the meter.
2. Press TIME (clock).
3. Press REC (n) or °C/°F (p) to increase or decrease the number.
4. Press TIME to move to the next item. The adjusting order is: year;
month; day; hour; minute.
5. Press TIME again after the last setting to complete the process.
To abort during a setup process, press the button.
4.6 Time Function
Once set up, pressing the TIME button displays time as follows: top of the LCD – year;
bottom left of the LCD - month and day; bottom right of the LCD - hour and minute.
Press the TIME button or any other button to exit this mode. This operation will not
interrupt the recording and MAX/MIN operation.
4.7 Recording Interval Setup
To set the recording interval:
1. Press and hold the MAX MIN button and then power on
the meter.
2. Press HOLD.
3. Press REC (n) or °C/°F (p) to increase or decrease the number.
4. Press HOLD to advance to the next item.
5. Press HOLD again after the last setting to complete the process.
To abort during a setup process, press the button.
MODEL 306 DUAL CHANNEL DATALOGGING THERMOMETER
4
TX RX GND
4.8 Recording Data
Each momentary press of the REC button will alternately start and
stop recording. To clear the memory, power off the meter, press
and hold the REC button followed by the button, holding both
on simultaneously for at least 2 seconds. Then release both
buttons. The display will show "CLR" (as shown to the right)
indicating that the memory has been cleared.
4.9 MAX/MIN Operation
Press the MAX MIN button to enter the MAX/MIN mode. In this mode, both the maximum
and minimum values are simultaneously retained in memory and updated with every new
data sample. The instrument first enters the MAX mode, and the MAX symbol and value
are both displayed. Pressing MAX MIN again advances the display to the MIN symbol
and value. The next press of the MAX MIN button will cause both the MAX and MIN
symbols to flash. This indicates that the maximum and minimum values have been
updated in memory and the displayed reading is the present temperature. Each
successive press of the MAX MIN button circulates the display mode among these
options. To exit the MAX/MIN mode, press and hold the MAX MIN button for two seconds.
In the MAX/MIN mode, the °C/°F button is disabled, as indicated by two consecutive
beeps if pressed.
4.10 Auto Power Off
By default, the instrument powers on in the ‘Auto Power Off’ mode and will automatically
shut off 30 minutes after the last key operation or RS232 communication.
To disable this feature, press and hold the HOLD button and then power on the meter.
Two successive beeps will indicate that ‘Auto Power Off’ is disabled, and the will not
be displayed.
4.11 Low Battery Condition
When the battery voltage is at or below the minimum for proper operation, the
symbol will show on the LCD indicating that the battery must be replaced.
4.12 Calibration
Calibration is conducted by adjusting the following potentiometers to within the
tolerances shown.
(Ambient Temperature: 23 ± 3°C)
Input Adjust VR Tolerance
0 °C VR1 ± 0.1 °C
190 °C VR2 ± 0.1 °C
1000 °C VR3 ± 1 °C
1900 °F VR4 ± 1 °F
4.13 Digital Output
The Digital Output is a 9600 bps N 81 serial interface.
RX is a 5V normally high input port.
TX is a 5V normally high output port.
Appendix: Thermocouple Probe Specifications
Model Range Tolerances Description
TP-K01
Wire probe
-50°C to 200°C
-58°F to 392°F
±2.2°C or ±0.75%
±3.6°F or ±0.75%
Teflon insulation. Maximum insulation
temperature: 260°C (500°F)
TP-K01:
Probe for general condition measurements, especially
for complex and hard to reach places.
