Monogram ZISW48D Handbuch

Monogram.

™

Specification Created 12/99

For answers to your Monogram,®

GE Profile Performance Series,™

GE Profile™or GE appliance questions, call

GE Answer Center®service, 800.626.2000.

Listed by

Underwriters

Laboratories

ZISB36DC - GE Monogram 36" Built-In Refrigerator with Dispenser and

Water Filter

Advanced Planning for a Flush Installation

Monogram built-in refrigerators are designed to be

installed with typical 24-3/4” deep cabinetry.

In a flush installation, the refrigerator doors will align

evenly with the front face of adjacent cabinets.

Side Panels Requirements:

•Side panels are not required whenever the refrigerator

is installed into an enclosure or between pantry and

oven cabinets.

•Side panels are required whenever the sides of the

refrigerator are exposed.

•Side panel sizes vary depending on type of installation

being made.

For a flush installation, you must:

1. Determine the need for side panels.

2. Determine side panel thickness.

3. Order matching side panels from the cabinet

manufacturer. Be sure to provide the exact dimensions.

The following cutout dimensions examples will provide a flush fit. If

you have a unique installation situation (other than those illustrated

here), see Product Dimensions to calculate the rough-in dimensions.

Installation Between Wall Oven and Pantry Cabinet

36"

Finished Dimension

Side panels are not required

whenever the refrigerator

is installed into an enclosure or

between pantry and oven

cabinets.

The minimum cutout for a

custom enclosure should be:

84”Hx36”Wx24-3/4”D

Design Information

Monogram.

™

Specification Created 12/99

For answers to your Monogram,®

GE Profile Performance Series,™

GE Profile™or GE appliance questions, call

GE Answer Center®service, 800.626.2000.

Listed by

Underwriters

Laboratories

1/4" Thick

Side Panels

35-1/2"

Finished Dim. 36"

Roughed-In Dim.

Note: 1/4” thick side panels can be

inserted into the case trim, making

the rough-in the same as the outside

trim width, 36”.

ZISB36DC - GE Monogram 36" Built-In Refrigerator with Dispenser and

Water Filter

Design Information

Installation Between Base & Wall Cabinets

Cabinet

Refrigeratordoor

Refrigerator

Cabinet

1/4” Side Panels. Insert end of side panel

into trim.

37"

1/2" Thick

Side Panels

36"

Finished Dim.

Roughed-In Dim.

Note: 1/2” thick side panels shown.

Side panels can be any thickness.

Add side panel thickness to outside

trim width (36”)to calculate the rough-

in dimension

Refrigerator

Cabinet

Refrigerator door

Cabinet

1/2” To 3/4” Side Panels. Leading Edge Flush

With Cabinet.

Installation at End of Run

Side panels, 1/2” minimum thickness are

required when using frameless cabinets. The

side panel acts as a spacer between the

cabinet and the case trim and prevents

interference with cabinet door swing.

Frameless Cabinets

36"

Finished Dimension

Refrigerator

Cabinet

Refrigerator door

Cabinet

1/2” To 3/4” Side Panels. Leading Edge Flush

With Cabinet.

Monogram.

™

Advantage

• The flush appearance allows the refrigerator to blend into the

surrounding cabinetry or wall.

• The flush fit uses less floor space.

• A custom continuous toekick may be used to form an unbroken line

at the base of cabinetry.

Disadvantage

• The enclosure must be constructed accurately and perfectly

square, otherwise, gaps between case trim and surrounding

cabinetry will show.

True Flush Installation Semi-Flush Installation

In a flush installation, the

refrigerator doors will align

evenly with the front-face

of adjacent cabinet doors.

These refrigerators

can also be installed

semi-flush into an enclosure

using the minimum cutout

width. The case trim provides

a frame around the refrigerator.

Advantage

• If cabinetry or enclosure is not perfectly square, the case

trim will cover the surrounding cabinetry edges.

Disadvantage

• The refrigerator will project forward, approximately

3/4” beyond the front face of surrounding cabinetry. The

top grille panel will project forward of upper cabinetry

or soffit.

ZISW48D ZISW42D ZISW36D

ZISB48D ZISB42D ZISB36D

ZIS48N ZIS42N ZIS36N

PRODUCT A* 83” 83” 83”

DIMENSIONS B 48” 42” 36”

C24-3/4” 24-3/4” 24-3/4”

FINISHED D* 84” 84” 84”

FLUSH E†48” Min. 42” Min. 36” Min.

ENCLOSURE F 24-3/4” Min. 24-3/4” Min. 24-3/4” Min.

FINISHED D* 84” 84” 84”

SEMI-FLUSH E†47-1/2” Min. 41-1/2” Min. 35-1/2” Min.

ENCLOSURE F 24” Min. 24” Min. 24” Min.

*Factory set installation height is 84”. Height adjustments are

accomplished with optional grille panel frame kits.

Order ZG2 grille panel kit for all ZIS models.

†Side panels are not required when installing into an enclosure.

Side panels are required whenever the sides of the refrigerator are

exposed. If side panels are used, add side panel thickness to

calculate finished cutout width.

Specification Created 12/99

ZISB36DC - GE Monogram 36" Built-In Refrigerator with Dispenser and

Water Filter

For answers to your Monogram,®

GE Profile Performance Series,™

GE Profile™or GE appliance questions, call

GE Answer Center®service, 800.626.2000.

Listed by

Underwriters

Laboratories

3/4"

See Installation Instructions for Details, Order Pub. No. 49-6964-2

for ZIS36 models, Pub. No. 49-6963-2 for ZIS42 models and Pub.

No. 49-6962-2 for ZIS48 models.

Electrical

Area 74"From Floor

Bottom

ofElectrical

31/2"

WaterSupply

36" Models 12-3/8"

42" Models 18-3/8"

48" Models 20-3/8"

Monogram.

™

Specification Created 12/99

For answers to your Monogram,®

GE Profile Performance Series,™

GE Profile™or GE appliance questions, call

GE Answer Center®service, 800.626.2000.

Listed by

Underwriters

Laboratories

ZISB36DC - GE Monogram 36" Built-In Refrigerator with Dispenser and

Water Filter

Dimensions and Specifications (in inches) Design Information: Designed to be installed flush with surrounding

cabinetry. Cutout dimensions, clearances and side panel sizes are

determined by the many installation options available. Side panels must

be used whenever the sides of the refrigerator will be exposed. Side panels

are not required when refrigerator is installed into an enclosure or between

pantry and oven cabinets. Important-Side panels, 1/2” min. thickness are

required for frameless cabinets.

Field installed custom panels, Lexan®or stainless steel panels are required.

Custom door panels and grille panel sizes vary to accommodate the kit

being used.

A custom toekick can be installed to match or complement the surrounding

cabinetry. A standard toekick is supplied. For a custom toekick, use supplied

toekick as a template to cut notches for hinges and water lines.

Optional Kits:

• ZWBP36: Black Lexan®Panel Kit (no trim kit required).

• ZWWP36: White Lexan®Panel Kit (no trim kit required).

• ZWSP36: Stainless Steel Panel Kit (no trim kit required).

• ZKH1: Provides for the installation of a custom handle on 1/4” custom

panels.

• ZG2: Provides 1/4” grille panel frame side pieces for 83”, 83-1/2” and 84-

1/2” installation heights. Factory set height is 84”.

• ZKT36: Provides for the installation of 3/4” custom door and grille panels.

• ZKHT1: Provides for the installation of a custom handle using 3/4”

custom panels. (This kit must be used in combination with ZKT36.)

• ZKHSS1: Tubular stainless steel handles on 1/4” panels.

• ZKHTSS1: Tubular stainless steel handles on 3/4” panels. This kit must

be used in combination with ZKT48.

• ZWCD1: Provides for the installation of a custom collar trim on the

dispenser for one continuous custom panel on the freezer door. This kit

can be used alone, or with one or more kits.

Additional Specifications: A 115 volt 60 Hz., 15 or 20 amp power supply

is required. An individual properly grounded branch circuit or circuit breaker

is recommended. Install a properly grounded 3-prong electrical receptacle

recessed into the back wall. Electrical must be located on rear wall.

Water line can enter opening through the floor or back wall. The water line

should be 1/4” O.D. copper tubing between the cold water line and water

connection location, long enough to extend to the front of the refrigerator.

Installation of an easily accessible shut off valve in the water line is

recommended.

Clearances: If the refrigerator is to be installed in a corner, a 4” min.

clearance between the case trim and adjacent wall on both sides of the

refrigerator will assure a 90° door opening and access to all drawers. A 10”

clearance is required on both sides for removal of pans.

Side View

(not to scale)

24 3/4"

Front View

(not to scale)

36" Overall Width

35" Case Width

84 1/2" max*

83" min

72 1/4"

12 1/4" max

10 3/4" min

*84" Shipping Height. For 84-1/2"

Height Installation order ZG2.

*The finished and rough-in dimensions are determined by the

type of installation being made. The rough-in cutout width

includes side panel thicknesses. See “Advanced Planning For

A Flush Installation.”

*35 1/2" - 37 1/2"

Wall View

(not to Scale)

Locate Grounded

Electrical outlet

Within Solid

Area Above

84 1/2" max

83" min

Finished

Rough

Opening

74"

From Floor to

Bottom of

Electrical Area

12 3/8"

5" 3 1/2"

3 1/2"

Locate Water

Supply Within

the Shaded

Area Below

*84” Shipping Height. For Other

Installation Heights order ZG2.

Monogram.

™

Specification Created 12/99

For answers to your Monogram,®

GE Profile Performance Series,™

GE Profile™or GE appliance questions, call

GE Answer Center®service, 800.626.2000.

Listed by

Underwriters

Laboratories

ZISB36DC - GE Monogram 36" Built-In Refrigerator with Dispenser and

Water Filter

Dimensions and Specifications (in inches)

The ZKT36 trim kit provides for the installation of 3/4” custom door and

grille panels, using the standard full-length handle. Cut panels to size and

install.

For standard dispenser trim: Cut panels to size, rout the bottom of the upper

freezer panel and the top of the lower freezer panel to allow placement of

support brackets and install (see detail A).

For custom dispenser trim ZWCD1 kit must be used: Cut panels to size,

refer to detail B for dispenser cutout routing instructions and install. When

a raised panel design is used, custom width stiles and custom middle rail

is required. A 13-1/2” wide middle rail must be used because the custom

collar trim must be located within the raised portion of the panel. This area

must be 3/4” thick. See Detail C for raised panel.

35 1/2"

AOver 1/4" Thick (3/4" max) Panel

Custom Grille Panel

(not to scale)

Grille Panel height can vary to fill installation height.

Important: Maintain 1-1/2" minimum gap between

top of doors and bottom of grille panel.

Custom Door Panel Dimensions When Using Trim Kit

ZKT36, 3/4” thick panel with standard handle and/or ZWCD1

custom collar trim (not to scale)

16-11/16"

37"

2-5/16"

67-15/16"

15-1/16" 19-1/16"

17-11/16"

Fresh Food

Panel

Freezer Panel

Standard

Dispenser

Freezer Panel

Custom

Dispenser

15-1/16"

3/32"

Upper

Freezer

Panel

Lower

Freezer

Panel

Face

Detail A Detail C

Raised Panel Design

*3"

Stile

Left

Side

Hole is

Cut After

Door

Fabrication

*2 3/16" Stile

Right Side

Section AA

Handle

Side

13 1/2"

Wide

Middle

Rail

The Cutout is 9 7/16" wide

by 12 5/16" high. 3/4" panels

must be routed on all four

sides of the cutout. Rout

the back side of the panel

1/4" deep 7/8" wide.

(shaded area)

12 5/16"

9 7/16"

7/8" wide rout

Detail B

Custom Dispenser Cutout

XInstallation Height Dimension A

83" 8-1/4"

83-1/2" 8-3/4"

84" 9-1/4"

84-1/2" 9-3/4"

Monogram.

™

Specification Created 12/99

For answers to your Monogram,®

GE Profile Performance Series,™

GE Profile™or GE appliance questions, call

GE Answer Center®service, 800.626.2000.

Listed by

Underwriters

Laboratories

XInstallation Height Dimension A

83" 8"

83-1/2" 8-1/2"

84-1/2" 9-1/2"

ZISB36DC - GE Monogram 36" Built-In Refrigerator with Dispenser and

Water Filter

Dimensions and Specifications (in inches)

35"

9" 1/4" Thick Panel

Custom Grille Panel

(not to scale)

Panel frame is factory assembled for 84"

installation height. If installation height

varies, order ZG2 trim kit which provides

optional side trim panels. Cut Lexan®or

stainless panels to sizes shown below.

9 7/16"

12 5/16"

Custom Dispenser

Cutout

The Cutout is 9 7/16"

wide by 12 5/16" high.

Custom Door Panel Dimensions Using StandardTrim

1/4" thick panels or Panels secured to 1/4" thick backing

1 1/4"

Clearance

hinge side 2" Clearance

handle side

Appearance

Panel

1/4"

Thick

Backing

Raised Panel on 1/4" Thick Backing

Door

Handle

Case Trim

16-5/8"

36-7/8"

2-9/16"

67-7/8"

15-1/4" 15-1/4" 19-1/4"

17-11/16"

Fresh Food Panel

Freezer Panel

Standard

Dispenser

Freezer Panel

Custom

Dispenser

Standard Trim with 1/4” Panels: 1/4” Panels: Cut panels to size.

Custom handles with 1/4” door panels require Trim Kit ZKH1. When using

ZKH1 with the standard dispenser trim, the length of the custom handle,

top to bottom cannot exceed 11-3/4”.

Tubular stainless steel handle kit ZKHSS1.

Custom collar dispenser trim with 1/4” door panels require trim kit ZWCD1.

Standard Trim with Panels secured to 1/4” thick backing: Applying a

raised panel design to a 1/4” thick backing (screwed or glued): Cut 1/4”

panels to size, fabricate the raised panel to permit clearances of at least 2”

from the handle side for fingertip clearance, 1-1/4” from the hinge side to

avoid striking adjacent cabinetry and 5/16” from the top and bottom edges

to allow for the trim flange, then install.

Countertops adjacent to refrigerator installation should be mitered 45°

degrees.

Note: ZWCD1 custom collar dispenser trim and ZKHT1 custom handle kits

cannot be used in this configuration.

Important: Maintain 1-1/2” min. gap

between top of doors and bottom of panel

frame.

Monogram.

™

Specification Created 12/99

For answers to your Monogram,®

GE Profile Performance Series,™

GE Profile™or GE appliance questions, call

GE Answer Center®service, 800.626.2000.

Listed by

Underwriters

Laboratories

ZISB36DC - GE Monogram 36" Built-In Refrigerator with Dispenser and

Water Filter

Dimensions and Specifications (in inches)

Custom Door Panel Dimensions When UsingTrim Kit

ZKT36 3/4" thick panel with custom handle and/or

ZWCD1 custom collar trim.

3/32"

Upper

Freezer

Panel

Lower

Freezer

Panel

Face

16-11/16"

37"

2-9/16"

67-15/16"

15-5/16" 19-5/16"

17-11/16"

Fresh Food

Panel

Freezer Panel

Standard

Dispenser

Freezer Panel

Custom

Dispenser

15-5/16"

1-13/16" 1-13/16"

1/4"

max

Freezer Door Face Fresh Food Door Face

The Cutout is 9 7/16" wide

by 12 5/16" high. 3/4" panels

must be routed on all four

sides of the cutout. Rout

the back side of the panel

1/4" deep 7/8" wide.

(shaded area)

12 5/16"

9 7/16"

7/8" wide rout

Detail C

Custom Dispenser Cutout

Detail B

Rout panels to specification below on

the handle side of each panel

*3"

Stile

Left

Side

Hole is

Cut After

Door

Fabrication

*2 3/16" Stile

Right Side

Section AA

Handle

Side

13 1/2"

Wide

Middle

Rail

Detail D

Raised Panel Design

Detail A

35 1/2"

AOver 1/4" Thick (3/4" max) Panel

Custom Grille Panel

(not to scale)

Grille Panel height can vary to fill installation height.

Important: Maintian 1-1/2" minimum gap between

top of doors and bottom of grille panel.

ZKT36 and ZKHT1 installed together provides for the installation of 3/4”

custom door and grille panels, using a custom handle of your choice. Cut

panels to size, rout the handle side of the panels as shown below and

install (see detail B). For ZKHTSS1, tubular stainless steel handle kit, cut

panels to size and rout the handle side of the panels as shown in detail B.

For standard dispenser trim: Cut panels to size, rout the handle side of the

panels as shown in detail B, rout the bottom of the upper freezer panel and

the top of the lower freezer panel to allow placement of support brackets

(see detail A) and install.

For custom dispenser trim ZWCD1 kit must be used: Cut panels to size,

refer to detail C for dispenser cutout routing instructions and install. When

a raised panel design is used, custom width stiles and custom middle rail is

required. A 13-1/2” wide middle rail must be used because the custom

collar trim must be located within the raised portion of the panel. This area

must be 3/4” thick. See Detail D for raised panel.

When using the standard full-width dispenser trim, the length of the custom

handle, top to bottom cannot exceed 11-3/4”. Locate the handle a minimum

of 3/4” and a maximum of 1-1/2” from the edge of the panel. There are no

length restrictions on handles for models using a custom collar dispenser

trim (ZWCD1).

XInstallation Height Dimension A

83" 8-1/4"

83-1/2" 8-3/4"

84" 9-1/4"

84-1/2" 9-3/4"

Monogram.

™

Specification Created 12/99

For answers to your Monogram,®

GE Profile Performance Series,™

GE Profile™or GE appliance questions, call

GE Answer Center®service, 800.626.2000.

Listed by

Underwriters

Laboratories

ZISB36DC - GE Monogram 36" Built-In Refrigerator with Dispenser and

Water Filter

Dimensions and Specifications (in inches)

1/2" to 3/4" Side Panels

Leading Edge

Flush with Cabinet

Front.

Side panels must be used whenever the sides of the refrigerator will be exposed.

23 9/16"

84"

2 9/16"

Trim

1/4" Side Panels

Insert end of

side panel into trim.

Standard 4" high toekick or trim to fit.

Height may vary depending on application.

24 3/4"

84"

3 3/4"

Standard 4" high toekick or trim to fit.

Height may vary depending on application.

Standard 4" high toekick or trim to fit.

Height may vary depending on application.

Standard 4" high toekick or trim to fit.

Height may vary depending on application.

23 5/16"

84"

2 5/16"

24 3/4"

84"

3 3/4"

1 1/2"

1/2" to 3/4" Side Panels

Leading edge routed

1/4" deep, 1-1/2" top to

bottom.

1/2" to 3/4" Side Panels

Recessed front edge.

*Not to scale.

Monogram.

™

Specification Created 12/99

ZISB36DC - GE Monogram 36" Built-In Refrigerator with Dispenser and

Water Filter Features and Benefits

•21.2 cu. ft. Capacity (Fresh Food 12.0 cu.

ft., Freezer 9.2 cu. ft.)

• GE SmartWater™Filtration System

• Exterior Dispenser with Cubes, Crushed

Ice and Chilled Water

• 2 Adjustable Humidity Vegetable/

Fruit Pans

• Sealed Snack Pan

• 4 Adjustable Spill-Proof Glass Fresh

Food Shelves

• Slide-Back Shelf

• 5 Adjustable Fresh Food Door Bins

• Dairy Compartment

• Wine Holder

• Glass-Covered Butter Dish

• 4 Adjsutable Wire Freezer Shelves

• 2 Utility Baskets

• 3 Adjustable Freezer Door Bins

• Full-Length Aluminum Door Handles

• Model ZISW36DC—White Dispenser

• Model ZISB36DC—Black Dispenser

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monogram Kühlschrank Handbücher

Monogram

Monogram ZWE23 SN SS Series Bedienungsanleitung

Monogram

Monogram ZDOD240 Bedienungsanleitung

Monogram

Monogram Monogram ZISB360DR Bedienungsanleitung

Monogram

Monogram ZDOD240 Bedienungsanleitung

Monogram

Monogram ZIFI240 Bedienungsanleitung

Monogram

Monogram ZIDS240 Bedienungsanleitung

Monogram

Monogram ZIFS240 Bedienungsanleitung

Monogram

Monogram ZIFI240 Bedienungsanleitung

Monogram

Monogram ZWE23PSHSS Bedienungsanleitung

Monogram

Monogram Built-in refrigerators Bedienungsanleitung

Monogram

Monogram ZISB42E Bedienungsanleitung

Monogram

Monogram ZIC360NXDLH Bedienungsanleitung

Monogram

Monogram Monogram ZFSB23DRSS Benutzerhandbuch

Monogram

Monogram ZICS360NRFRH Bedienungsanleitung

Monogram

Monogram ZIS360N Leitfaden

Monogram

Monogram ZIFI240 Bedienungsanleitung

Monogram

Monogram ZIRNPKII Bedienungsanleitung

Monogram

Monogram Bottom-Freezer Built-In Refrigerators Bedienungsanleitung

Monogram

Monogram ZIRS36N LH Bedienungsanleitung

Monogram

Monogram ZIFI240 Bedienungsanleitung

Monogram

Monogram ENERGY STAR ZWE23ESHSS Bedienungsanleitung

Monogram

Monogram ZIS360N Bedienungsanleitung

Monogram

Monogram ZIR36N LH Anleitung zur Verwendung

Monogram

Monogram ZSGS420D Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung