Monogram ZVC48DNB1 Bedienungsanleitung
INSTALLATION
INSTRUCTIONS
48”Designer Brass Hood
ZVC48DNB1
MONOGRAM.COM
231-2000730 Rev. 0
Safety Information
READ AND SAVE THESE INSTRUCTIONS
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Ŷ
IMPORTANT— Save these instructions
for local inspector’s use.
Ŷ
IMPORTANT— Observe all governing
codes and ordinances.
ŶNote to Installer — Be sure to leave these
instructions with the Consumer.
ŶNote to Consumer — Keep these instructions with
your Owner’s Manual for future reference.
ŶSkill Level — Installation of this appliance requires
basic mechanical and electrical skills.
Ŷ3URSHULQVWDOODWLRQLVWKHUHVSRQVLELOLW\RIWKH
LQVWDOOHU3URGXFWIDLOXUHGXHWRLPSURSHULQVWDOODWLRQ
is not covered under the warranty. See Owner’s
Manual for warranty information.
WARNING Improper grounding can result in a
risk of electric shock. Consult a qualified electrician
if the grounding instructions are not completely
understood, or if doubt exists as to whether the
appliance is properly grounded.
For Monogram local service in your area,
800.444.1845.
For Monogram Service in Canada, call 800.561.3344.
)RU0RQRJUDP3DUWVDQG$FFHVVRULHVFDOO
800.626.2002.
If you received a damaged vent hood, you should
contact your dealer.
CAUTION Due to the weight and size of these
vent hoods and to reduce the risk of personal injury
or damage to the product, TWO PEOPLE ARE
REQUIRED FOR PROPER INSTALLATION.
WARNING TO REDUCE THE RISK OF FIRE,
(/(&75,&$/6+2&.25,1-85<723(56216
2%6(59(7+()2//2:,1*
Ŷ,QVWDOODWLRQZRUNDQGHOHFWULFDOZLULQJPXVWEHGRQHE\
qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction.
Ŷ:KHQFXWWLQJRUGULOOLQJLQWRZDOOVRUFHLOLQJVGRQRW
damage electrical wiring and other hidden utilities.
Ŷ'XFWHGV\VWHPVPXVWDOZD\VEHYHQWHGWRWKHRXWGRRUV
CAUTION To reduce risk of fire and to properly
exhaust air, be sure to duct air outside — do not vent
exhaust air into spaces within walls or ceilings or into
attics, crawl spaces or garages.
WARNING TO REDUCE THE RISK OF FIRE,
86(21/<0(7$/'8&7:25.
31-2000730 Rev. 0 3
Installation Instructions
CONTENTS
Safety Information.........................................................2
3URGXFW'LPHQVLRQV ......................................................3
$GGLWLRQDO3DUWV3URYLGHG..............................................3
Tools and Materials Required.......................................3
Installation Clearances..................................................4
$GYDQFH3ODQQLQJ .........................................................4
Unboxing .......................................................................4
Step 1, Determine Ductwork and Wiring Locations ......5
Step 2, Install Hood onto Wall.......................................6
Step 3, Install Hood Insert into Hood............................7
PRODUCT DIMENSIONS
ADDITIONAL PARTS PROVIDED
These parts are packed with the hood. TOOLS AND MATERIALS REQUIRED
1RWVXSSOLHG
28”
16”
22”
SIDE VIEW FRONT VIEW
38-5/8”
48”
Phillips screwdriver
Flashlight
Safety glasses
Electric or battery operated drill.
1/8” drill bit. 3/16” drill bit.
Phillips driver.
Pencil
Level Step ladder
Tape measure
Safety Gloves
Wood Support with
short Phillips head screws
2 long Square Drive flat head
screws to secure the wood
support to the wall
Square drive bit
2 short pan head Phillips screws to
secure the hood to the wood support.
There are 2 additional screws already
installed in the wood support.
4 medium pan head Phillips screws to
secure the hood to the wall.
431-2000730 Rev. 0
Installation Instructions
INSTALLATION CLEARANCES
This hood is designed to be installed onto a wall.
Install this hood 30" minimum to 36" maximum above the
cooking surface.
In this installation, the ductwork running from the top
of the hood will be concealed in the soffit or upper
cabinetry.
In this installation, the ductwork running from the back
of the hood goes directly into the wall.
ADVANCED PLANNING
Ductwork Planning
Ŷ&DUHIXOO\UHYLHZWKHGXFWZRUNLQVWDOODWLRQPHWKRGDV
described later in this instruction as well as the hood
insert installation instructions.
Wall Framing for Adequate Support
Ŷ7KLVKRRGLVKHDY\$GHTXDWHVWUXFWXUDOVXSSRUWPXVW
be provided. Hood must be secured to vertical studs in
the wall.
Ŷ,WLVVWURQJO\UHFRPPHQGHGWKDWWKHKRRGDQGKRRG
insert be on site before final framing and wall finishing.
This will also help to accurately locate the ductwork
and electrical service.
UNBOXING
NOTE: Clearances may vary due to type of
cooking product and local codes. Check with local
inspectors to be sure standard is applicable.
SOFFIT OR UPPER CABINETS
Top Vent Installation
30" MIN.
36" MAX.
Back Vent Installation
30" MIN.
36" MAX.
Cut Straps Remove Top Remove Sleeve Remove Hood
31-2000730 Rev. 0 5
Installation Instructions
STEP 1 DETERMINE HOOD AND DUCTWORK LOCATIONS
MARK LOCATION OF WOOD SUPPORT
Ŷ8VHDOHYHOWRGUDZDFRRNWRSFHQWHUOLQHORFDWLRQ
Draw the line to ceiling height.
Ŷ0HDVXUHGHVLUHGGLVWDQFHIURPWKHERWWRPRIWKHKRRG
to the cooking surface, 30” min. to 36” max.
Ŷ8VHDOHYHOWRGUDZDVWUDLJKWKRUL]RQWDOSHQFLOOLQH
indicating the bottom of the hood.
Ŷ)URPWKHOLQHLQGLFDWLQJWKHERWWRPRIWKHKRRG
measure 16” up and draw another line for the location
of the wood support.
Ŷ)URPWKHOLQHLQGLFDWLQJWKHERWWRPRIWKHKRRG
measure 28” up and draw another line for the location
of the top of the hood. See illustration.
16”
Bottom of Hood
Wood
Support
Top of Hood
28”
FOR VERTICAL (Straight Up) DUCTING:
Ŷ8VHDOHYHOWRGUDZDFHQWHUOLQHIURPWKHERWWRPRIWKH
hood to ceiling or soffit.
Ŷ([WHQGWKHFHQWHUOLQHIRUZDUGRQWKHFHLOLQJRUVRIILW
Ŷ0DUNWKHFHQWHURID´KROHRQWKHFHLOLQJRUVRIILW
E\PHDVXULQJ´IURPWKHZDOO
FOR DUCTING THROUGH REAR WALL:
Ŷ0HDVXUH´DERYHWKHPDUNHGOLQHIRUWKHWRSRI
WKHZRRGVXSSRUW$WWKHFHQWHUOLQHPDUNORFDWLRQIRUD
´GLDPHWHUKROH
HOUSE WIRING LOCATION:
Ŷ/RFDWHMXQFWLRQER[DERYHWKHZRRGVXSSRUW
and to the left of the centerline as shown in the
illustration.
8-1/2” hole
8-1/2”
Bottom of Hood
Wood
Support
Top of Hood
4-3/4”
8-1/2” hole
Wood
Support
Top of Hood
Locate House Junction
Box Here
2”
2-3/4”
7”
6”
6”
631-2000730 Rev. 0
Installation Preparation
STEP 2 INSTALL HOOD TO WALL
Mount Wood Support to Wall
Ŷ/RFDWHDWOHDVWYHUWLFDOVWXGVDWWKHZRRGVXSSRUW
Ŷ&HQWHUWKHVXSSOLHGZRRGVXSSRUWOHIWWRULJKWDQG
below the 16” marked line. Use the center hole in the
wood support as guidance.
Ŷ0DUNDQGGULOOWZR´KROHVWKURXJKZRRGVXSSRUWWR
match stud locations.
Ŷ6HFXUHWKHZRRGVXSSRUWWRRUPRUHYHUWLFDOVWXGV
using 2 long, square drive screws.
IMPORTANT: Screws must penetrate at least 1” into
vertical studs. Countersink screws in support.
NOTE: The two supplied mounting screws must remain
in their original shipping location. These screws are
positioned to engage the keyhole slots in the back of the
hood.
Ŷ$GMXVWGHSWKRIVXSSOLHGPRXQWLQJVFUHZVLQWKHZRRG
VXSSRUWXQWLOWKH\SURWUXGH´IRUZDUG7KLV´JDS
will provide clearance to hang the hood.
IMPORTANT: Framing must be capable of
supporting up to 150 lbs.
Ŷ3ODFHWKHKRRGRYHUWKHZRRGVXSSRUW%HVXUHWKH
mounting screws engage the keyhole slots in the
back of the hood. Tighten the screws. Confirm hood
position is correct.
Ŷ,QVWDOODGGLWLRQDOVKRUWVFUHZVWRVHFXUHWKHKRRGWR
the wood support.
Ŷ,QVWDOOPHGLXP3KLOOLSVVFUHZVDWWRSLQVLGHRIWKH
hood into studs. Chose the appropriate holes that line
up with studs.
Ŷ,QVWDOOPHGLXP3KLOOLSVVFUHZVDWERWWRPLQVLGHRI
hood into studs. Choose the appropriate holes that
line up with studs.
30”
to
36”
16” Wood Support
Centerline of
Installation
Space
Mounting Screws
as Shipped
1/4”
Gap
Centerline of
Installation
Space
30”
to
36”
Keyhole Slots
choose screw holes that line up with studs
choose screw holes that line up with studs
31-2000730 Rev. 0 7
Installation Preparation
STEP 3 INSTALL HOOD INSERT INTO HOOD
5HIHUQRZWRWKHLQVWDOODWLRQLQVWUXFWLRQVIRUWKH&XVWRP+RRG,QVHUW=9&ZLWKWKHIROORZLQJH[FHSWLRQV
Ŷ'LVUHJDUGDQ\UHIHUHQFHWREXLOGLQJDFXVWRPZRRG
canopy.
Ŷ'LVUHJDUGDQ\UHIHUHQFHWRWKH+RRG/LQHU,WLVQRW
required when using this hood.
Ŷ)RUGXFWSODQQLQJ\RXZLOOQHHGWRUHIHUWRWKHVH
instructions as some of the dimensions are different.
Ŷ<RXPD\UHPRWHPRXQWWKHFRQWUROIRUWKH+RRG,QVHUW
if desired.
Ŷ6NLS6WHS,QVHUW+RRG/LQHU<RXPD\GLVFDUGWKH
Liner, it is not required.
Ŷ6WDUWDW6WHS&RQQHFW(OHFWULFDO
Ŷ%HVXUHWRIROORZWKHUHPDLQGHURIWKH&XVWRP+RRG
Insert installation instructions to properly fasten the
Insert to the Hood.
Ŷ3D\VSHFLDODWWHQWLRQWRWKHVWHSWKDWVD\VWRSXVK
the Insert firmly up prior to driving screws. This will
prevent any visible gaps between the Insert and the
Hood.
Use provided screws to attach the Insert to the Hood as directed
in the Insert Installation Instructions.
31-2000730 Rev. 0
02-20 GEA
Printed in the United States
NOTE: While performing installations described in this book, safety glasses or
goggles should be worn.
NOTE: Product improvement is a continuing endeavor at Monogram. Therefore,
materials, appearance and specifications are subject to change without notice.
Andere Handbücher für ZVC48DNB1
2
Inhaltsverzeichnis
Andere Monogram Dunstabzugshaube Handbücher
Monogram
Monogram ZV900 Bedienungsanleitung
Monogram
Monogram ZV30 Bedienungsanleitung
Monogram
Monogram ZEM115SFSS Bedienungsanleitung
Monogram
Monogram ZV48SSJSS Bedienungsanleitung
Monogram
Monogram ZDWI240 Bedienungsanleitung
Monogram
Monogram ZV48T Bedienungsanleitung
Monogram
Monogram ZX8D13SPXX Bedienungsanleitung
Monogram
Monogram ZV900 Bedienungsanleitung
Monogram
Monogram Stainless Steel Range Hood Bedienungsanleitung
Monogram
Monogram Monogram Downdraft Vent System Bedienungsanleitung
Monogram
Monogram ZV800SJ2SS Bedienungsanleitung
Monogram
Monogram ZV1050 Bedienungsanleitung
Monogram
Monogram ZVC48DNB1 Bedienungsanleitung
Monogram
Monogram ZV1050 Bedienungsanleitung
Monogram
Monogram ZV48SSJSS Bedienungsanleitung
Monogram
Monogram ZV800SJSS Bedienungsanleitung
Monogram
Monogram ZV925 Bedienungsanleitung
Monogram
Monogram ZVC48STSS Bedienungsanleitung
Monogram
Monogram ZV830 Bedienungsanleitung
Monogram
Monogram ZV42I Bedienungsanleitung
