Morgan MSG-27MAXIcare Bedienungsanleitung

E-mail: electrical.appliance@dksh.com

www.morgan.my

Market Expansion

Services by

www.dksh.com.my

facebook.com/morganappliances

USER MANUAL

Steam

Generator

MSG-27MAXIcare

MSG-27MAXIcare(IM)241017. xp_Layout 1 12/5/17 4:20 PM Page 1

PARTS IDENTIFICATION

C O N T E N T S

4-5

7-8

9-10

PARTS IDENTIFICATION

IMPORTANT SAFEGUARDS

SPECIFICATIONS

PREPARING FOR FIRST USE

OPERATING INSTRUCTIONS

CLEANING AND MAINTENANCE

STORAGE

TROUBLESHOOTING

A. Steam supply hose

B. Ironing platform

C. Power cord with power plug

D. Power button

E. Steam supply hose storage

compartment

F. CALC- Clean knob

G. Eco mode light

H. Eco and steam function selector button

I. Water tank empty light

J. Steam operation light

K. Calc clear light

L. Standby activator and calc clear

reset button

M. Standby activator light

N. Water tank unlock button

O. Detachable water tank

P. Carry lock

. Carry lock release button

R. Water filling inlet

S. Steam trigger

T. Dial knob

U. Iron ready light

V. Sole plate

MSG-27MAXIcare(IM)241017. xp_Layout 1 12/5/17 4:20 PM Page 2

IMPORTANT SAFEGUARDS

lease read through the following safety precautions carefully before using the

appliance and save it for future reference.

WARNING! NEVER IMMERSE THE A LIANCE IN WATER.

SAFET PRECAUTIONS

• Before plugging the appliance into the power supply, ensure that the voltage and power

supply comply with the specifications indicated on the rating plate of the appliance.

• Do not operate the appliance if the power plug or power cord have been damaged, or if

not functioning properly.

• If the power plug, power cord or the supply hose is damaged, have it replaced by an

authorized service technician or a similarly qualified person to avoid a hazard.

• Never leave the appliance unattended when connected to the power supply.

• This appliance is not intended for use for by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge unless they

have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety.

• This appliance can be used by children aged from 12 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved.

• Keep the appliance and power cord away from children when the appliance is switched

on or cooling down.

• Children are only allowed to clean the appliance and perform the Calc-Clean produce

under supervision.

• Do not allow the power cord and supply hose to contact with the hot sole plate of the iron.

• Tighten the CALC-Clean knob if steam or hot water droplets escape from under the

CALC-Clean knob when operating the appliance. If steam continues to escape when the

appliance warms up, switch off the appliance and contact your nearest service authorized

service center.

• Do not remove the CALC-Clean knob from the appliance when hot or under pressure.

• Do not use any other accessories/attachments on the appliance other than the

CALC-Clean knob that has been supplied with the appliance.

• Always place the appliance on a stable, flat, heat-resistant surface. Ensure that the

surface can take the weight of the unit during use and when the appliance is resting on

its stand.

• The Steam Iron is intended for DOMESTIC USE ONLY and should not be used for

commercial purposes.

IMPORTANT

• Only connect the appliance to an earthed power supply socket.

• Always inspect the power cord and the supply hose regularly for possible damage.

• Fully unwind the power cord before you plug it into the power supply socket.

• WARNING: The iron platform and the soleplate of the iron can become extremely hot and

may cause burns if touched. Do not touch the ironing platform when moving the

appliance.

• IM ORTANT: Always switch off the appliance and place it back into the ironing platform

before removing the power cord from the power supply when ironing has completed,

cleaning the appliance, when filling or emptying the appliance and when leaving the

appliance even for a short while.

• It is recommended to descale the appliance regularly according to the instructions in the

chapter “Cleaning and Maintenance”.

ELECTROMAGNETIC FIELDS (EMF)

This appliance complies with all standards regarding electromagnetic fields (EMF). If

handled properly and according to the instructions in this user manual, the appliance

is safe to use based on scientific evidence available today.

SPECIFICATIONS

Model MSG-27MAXIcare

Rated Voltage / Frequency 220-240V~ 50-60Hz

Rated Wattage 2000-2400W

Water Tank Capacity 1.5L

MSG-27MAXIcare(IM)241017. xp_Layout 1 12/5/17 4:20 PM Page 3

PREPARING FOR FIRST USE OPERATING INSTRUCTIONS

SETTING THE TEMPERATURE

1. Check the ironing instruction label on the garment to determine the correct ironing

temperature.

2. Place the iron on the ironing stand.

3. Insert the power plug into the power supply.

4. Select the appropriate temperature on the iron by rotating the temperature dial.

• Synthetic

• Silk/Wool

• Cotton/Linen

5. The green “steam ready” indicator lamp will illuminate after approximately 2 minutes,

indicating that the appliance is ready to use with steam. The iron pilot light will remain lit

while the iron is heating and will disappear as soon as the iron has reached the selected

temperature.

TI S:

• Sort your garments out based on their cleaning symbol labels. Always starting ironing with

clothes required to be ironed at the lowest temperatures.

• If unsure what the garment is made of then begin ironing at a low temperature and decide

on the right temperature by ironing a small section not usually seen when worn.

STEAM IRONING

1. Place the appliance on a stable and level surface, e.g. on the hard part of the ironing

board or on a table.

2. Ensure that sufficient water in the water tank (refer to section “filling the detachable water

tank”).

FILLING THE DETACHABLE WATER TANK

Do not fill water tank with hot water, perfume, vinegar, starch, descaling agents,

ironing aids or other chemicals.

NOTE: Do not tilt or shake the appliance when the water tank is full, otherwise water may

spill out of the water inlet.

You can detach the water tank and fill it at any time during use.

Fill the water tank before first use and as soon as the water tank empty light flashes.

WATER TANK REFILL LIGHT

When the water tank is almost empty, the water tank empty light will illumnate and

steam ironing is no longer possible.

1. Remove the water tank and fill it.

2. Assemble the water tank back into the appliance.

3. The iron is ready for steam ironing again. OPERATION

1. remove the detachable water tank from the

appliance.

2. Fill the water tank with tap water up to the MAX

indication.

NOTE: if the tap water in your area is hard, we

advise you to mix it with an equal amount of

distilled water.

3. Turn the temperature dial to the steam position between

•• and MAX.

(If a too low temperature has been selected and the

steam function is used water may leak from the sole

plate).

4. Insert the power plug in an earthed wall socket and press

the on/off button to switch on the appliance.

The iron ready light will illuminate, indicating that the

appliance is heating up.

When the appliance is ready for use, the iron ready light

will illuminate continuously

3. Slide the water tank back into the appliance

(click).

NOTE: if the water tank is not proper in placed,

the iron does not produce any steam.

MSG-27MAXIcare(IM)241017. xp_Layout 1 12/5/17 4:20 PM Page 4

8 9

OPERATING INSTRUCTIONS CLEANING AND MAINTENANCE

5. Press the carry lock release button to unlock the iron

from the iron platform.

6. Press and hold the steam trigger to begin steam

ironing.

ECO STEAM IRONING

Select the ECO setting for optimum ironing performance at temperature settings ··and MAX.

VERTICAL STEAM IRONING

Hot steam is emitted from the iron. Never attempt to remove creases from a garment that is

worn. Do not apply steam near your or someone else’s hand.

AUTO-SHUT-FUNCTION

The appliance automatically switches off when it is not in use for a while (approx. 8minutes)

and the auto-shut-off light in the on/off button starts to flash. Activate the appliance to begin

heating again.

1. Hang the garment on a clothes hanger and pull the

garment tight with one hand.

2. Hold the iron in vertical position with the other hand

and press the steam trigger to steam iron the

garment.

3. Touch the garment lightly with the sole plate of the

iron to remove creases.

DESCALING THE APPLIANCE WITH CALC-CLEAN KNOB

To prevent scale build-up inside the appliance and to ensure long-lasting steaming

performance, this appliance has a CALC- Clean light on the control panel. This light will

illuminate after about a month or 10 ironing sessions. When this light illuminates, perform

the procedure with the CALC- Clean knob by following the steps below.

Never remove the CALC - CLEAN knob when the appliance is hot.

1. Press the on/off button to switch off the appliance and

remove the power plug from the power supply.

2. Allow the appliance to cool down for 2 hours

3. Place the appliance on a stable table top, with the

CALC - Clean knob over the edge of the table top.

TI : You can also take the appliance to a sink and

place it so that the CALC- Clean knob is pointing

towards the sink.

1. Hold a 350CC cup under the CALC - Clean knob to

collect the water that flows out.

2. Turn the CALC - Clean knob anti-clockwise to detach

and to allow the water with scale particles to flow out

into the cup.

NOTE: water starts flowing out of the appliance as

soon as you turn the CALC - Clean knob to remove it.

NOTE: this appliance is specially designed to remove

scale together with the water easily and effectively. It

is not necessary to shake or tilt the appliance.

1. When no more water comes out of the appliance,

reinsert the CALC - Clean knob and turn it clockwise to

fasten it.

2. Insert the power plug into an earthed power supply and

press the CALC - Clean reset button to reset the CALC-

Clean function. The CALC - Clean light will disappear.

MSG-27MAXIcare(IM)241017. xp_Layout 1 12/5/17 4:20 PM Page 5

10 11

CLEANING AND MAINTENANCE TROUBLESHOOTING

This chapter summarizes the most common problems encountered with the

appliance. If you are unable to solve the problem with the information below, contact

your nearest authorized service center.

CLEANING THE SOLE PLATE

Clean the sole plate regularly to move stains.

1. Insert the power plug into an earthed power supply and press the on/off button to switch

on the appliance and allow it heat up.

2. After approx.2 minutes, press the on/off button again to switch off the appliance and

detach the power plug from the power supply.

3. Place a piece of moist cotton cloth on the ironing board.

4. Iron over the cotton cloth repeatedly to remove stains from the sole plate.

Do not discard the appliance with the normal household waste at the

end of its lifespan, but hand it in at an official collection point for

recycling. By doing this, you will help to preserve the environment.

STORAGE

1. Press the on/off button to switch off the appliance

and detach the power plug from the power supply.

2. Detach the detachable water tank and empty it.

3. Place the iron on the iron platform.

4. Turn the carry lock over the tip of the sole plate to

lock the iron onto the iron platform.

5. Fold the supply hose and power cord to store them in

their respective storage compartments.

6. You can now easily carry the appliance by the handle

of the iron with one hand.

Do not carry the appliance by holding the water tank

release lever.

ROBLEM OSSIBLE CAUSES SOLUTION

The applia ce produces Water is pumped i to the boiler i side the If the pumpi g sou d persists co ti uously,

a loud pumpi g sou d. applia ce. This is ormal. switch off the applia ce a d remove the

power plug from the power supply. Co tact

your earest authorized service ce ter.

There is ot e ough water i the water ta k. Fill the water ta k.

The applia ce is ot hot e ough to produce Wait u til the iro ready light illumi ates

steam. co ti uously.

The applia ce does ot Steam trigger ot pressed. Press a d hold the steam trigger while

produce a y steam. steam iro i g.

The water ta k is ot secured properly. Slide the water ta k firmly back i to the

applia ce’s proper positio (click).

The applia ce is ot switched o . I sert the power plug i to the power supply

a d press the o /off butto to switch o the

applia ce.

The applia ce has The auto-shut-off fu ctio is activated Press the o /off butto to switch o the

switched off. automatically whe the applia ce has ot applia ce agai .

bee used for more tha 10 mi utes.

The light i the o /off The auto-shut-off fu ctio is activated Press the o /off butto to switch o the

butto illumi ates. automatically whe the applia ce has ot applia ce agai .

bee used for more tha 10 mi utes.

Water droplets escape from Whe you start steam iro i g a d i the This is ormal. Hold the iro over a old

the sole plate. eve t of a i terruptio , the steam i side the cloth a d press the steam trigger. The cloth

hose would have cooled dow a d absorb the water droplets. After a few

co de sed i to water, causi g water droplets seco ds, steam i stead of water comes

to escape from the sole plate. out of the soleplate.

Wet spots appear o the The wet spots that appear o your garme t Iro the wet spots without steam for some

garme t duri g iro i g. after you have steam iro ed for some time time to dry them. If the u derside of the

may be caused by steam that has co de sed iro i g board is wet, wipe it dry with a piece

o to the iro i g board. of dry cloth.

Flakes a d impurities come Impurities or chemicals prese t i the water Clea the soleplate with a damp cloth.

out of the sole plate or the may have deposited i the steam ve ts

the sole plate is dirty. a d/or o the soleplate.

Too much scale a d mi erals have Descale the applia ce regularly (see chapter

accumulated i side the applia ce. o “clea i g a d mai te a ce”, sectio –

descali g the applia ce with the

CALC-Clea k ob)

Water leaks from the If you tilt the applia ce duri g while movi g Do ot tilt the applia ce whe the water ta k

applia ce. it or place it o a u eve surface with the is full.

water ta k full, water may spill out of the

water ta k.

MSG-27MAXIcare(IM)241017. xp_Layout 1 12/5/17 4:20 PM Page 6

Inhaltsverzeichnis

Andere Morgan Eisen Handbücher

Morgan

Morgan MSI-SC15CS Bedienungsanleitung

Beliebte Eisen Handbücher anderer Marken

Clatronic

Clatronic DB 3703 Bedienungsanleitung

TEFAL

TEFAL FV4093Z0 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 BS Bedienungsanleitung

Philips

Philips GC6012 Bedienungsanleitung

Bosch

Bosch 2 Series Bedienungsanleitung

Riffel

Riffel Catena KB-819 Bedienungsanleitung

Texi

Texi Hestia Bedienungsanleitung

Maxwell

Maxwell MW-3010 Bedienungsanleitung

TREVIDEA

TREVIDEA Girmi ST60 Bedienungsanleitung

Philips

Philips HI5914/30 Bedienungsanleitung

Primula

Primula Vapormat Bedienungsanleitung

Magio

Magio MG-541 Bedienungsanleitung

Scarlett

Scarlett SC-1334S Bedienungsanleitung

Bosch

Bosch Sensixx B22L Bedienungsanleitung

Philips

Philips GC651 Bedienungsanleitung

Vitek

Vitek VT-1247 VT Bedienungsanleitung

Cleanmaxx

Cleanmaxx 3397 Bedienungsanleitung

Philips

Philips GC800 Bedienungsanleitung