MORLEY SPRINGWOUND Bedienungsanleitung

Buy A Morley. And Step On It.

SPRING REPLACEMENT INSTRUCTIONS FOR:

MARK 1, VAI-1, VAI-2, PBA, PBA-2, NSW OR WAH-SP (wound spring style)

Follow the below instructions to replace a broken or fatigued spring on any of the above

mentioned pedal models.

Tools you will need:

-12 mm nut driver

-5/16” nut driver

-1/4” nut driver

-Phillips Screwdriver (medium tip)

-Long tip Needle-nose pliers (2” long tip)

-3/8” Wrench (Open end or Box end)

DISASSEMBLY

1) Remove four bottom cover screws using Phillips screwdriver.

2) Remove bottom cover.

3) Remove two Chrome jack nuts and black plastic rings from 1/4” input and output jacks.

4) Remove four 1/4” nuts that hold down circuit board.

5) Slip battery snap out from battery foam slit.

6) The circuit board can now be removed from base.

7) Remove four 5/16” nuts, four 6-32 x 1/2” Phillips pan head screws and three washers that attach base to

treadle.

8) The base, treadle and spring will be completely disassembled at this point. Discard old spring.

CAUTION: Coiled spring steel version may have sharp edges especially where a break has occurred!

ASSEMBLY

1) Diagram 1 indicates the direction in which the spring should when assembled. The short side of the spring

(also indicated in diagram #1) should rest on the surface of the bracket. Although the diagrams show a pedal

with a base, the spring is to be assembled to the treadle/treadle bracket first.

2) Diagram #2 shows the proper assembly order of spring and associated components.

3) Place all components (per diagram #2) into place.

4) Place base onto treadle and align screw hole openings in base to line up with holes in treadle bracket.

5) Place a int. tooth washer on 6-32 a 1/2” screw. Using the needle-nose pliers, hold the 6-32 x 1/2” Phillips

pan head screw by the head and insert from underside of treadle bracket. (The thread should stick up in the

inside of the pedal base) Replace washer and 5/16” nut. Repeat for three remaining mounting locations. Do

not tighten any of the four nuts yet.

6) Align and center treadle to base. This can be accomplished by setting the pedal assembly on its heel end,

pushing the treadle as far toward the toe end as possible and visually centering the treadle so it is not cocked

to the right or left. This is important so the shutter is located properly between the optics.

7) Tighten the four 5/16” nuts thoroughly.

8) Set the screw tightness on each side of the treadle. To accomplish this, place the 3/8” wrench on the nut

located on the inside of the treadle/bracket assembly. Tighten bolt all the way down and loosen it one half turn

to allow treadle to move freely. Repeat for opposite side.

9) Replace circuit board, four 1/4” nuts, two black plastic rings & two chrome jack nuts.

10) Insert battery snap through the slit in battery foam.

11) Perform sound test to verify wah setting is still within acceptable range.

12) Replace bottom cover and bottom cover screws.

13) Diagram #3 shows the assembled spring.

If you need further assistance, please call 1-800-284-5172

Bill Wenzloff ext 12

Chad Montrose ext 14

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MORLEY Musikpedal Handbücher

MORLEY

MORLEY MTMES Bedienungsanleitung

MORLEY

MORLEY EP-11 Bedienungsanleitung

MORLEY

MORLEY PWVSSES Bedienungsanleitung

MORLEY

MORLEY SLSV2 Bedienungsanleitung

MORLEY

MORLEY XWVES Bedienungsanleitung

MORLEY

MORLEY OTHER Bedienungsanleitung

MORLEY

MORLEY TRIPLERES Bedienungsanleitung

MORLEY

MORLEY PWAES Bedienungsanleitung

MORLEY

MORLEY PWONEW Bedienungsanleitung

MORLEY

MORLEY NSWES Bedienungsanleitung

MORLEY

MORLEY SLVO2 Bedienungsanleitung

MORLEY

MORLEY PCB2 Bedienungsanleitung

MORLEY

MORLEY D1B1 Bedienungsanleitung

MORLEY

MORLEY CSVES Bedienungsanleitung

MORLEY

MORLEY DDB Bedienungsanleitung

MORLEY

MORLEY CWVES Bedienungsanleitung

MORLEY

MORLEY POWER WAH Bedienungsanleitung

MORLEY

MORLEY CWAES Bedienungsanleitung

MORLEY

MORLEY SPRINGCOILED Bedienungsanleitung

MORLEY

MORLEY SFB Bedienungsanleitung

MORLEY

MORLEY PWASS Bedienungsanleitung

MORLEY

MORLEY SLMC61 Bedienungsanleitung

MORLEY

MORLEY PVOES Bedienungsanleitung

MORLEY

MORLEY PBAES Bedienungsanleitung

Beliebte Musikpedal Handbücher anderer Marken

Behringer

Behringer ULTRA WAH UW300 Bedienungsanleitung

Whirlwind

Whirlwind oc-bass Bedienungsanleitung

Strymon

Strymon Lex-rotary Bedienungsanleitung

Behringer

Behringer PB600 Bedienungsanleitung

Lexicon

Lexicon MX200 Bedienungsanleitung

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Bedienungsanleitung

Matthews Effects

Matthews Effects Whaler V2 Bedienungsanleitung

Grid 1

Grid 1 Pedal Jeanie Bedienungsanleitung

Amptweaker

Amptweaker tightboost Bedienungsanleitung

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Bedienungsanleitung

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER Bedienungsanleitung

BYOC

BYOC Analog Chorus Handbuch

Dimavery

Dimavery EPVP-50 Bedienungsanleitung

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Bedienungsanleitung

Pro-MIDI

Pro-MIDI G25 Bedienungsanleitung

DW 7000 Bedienungsanleitung

FAMC

FAMC Liquid-Foot Jr. Series Bedienungsanleitung

Dimavery

Dimavery EPOD-50 Overdrive Bedienungsanleitung