Morningstar SunSaver Series Leitfaden

SunSaver

Field Testing Procedures

Abstract:

The following test procedure was developed for use in ﬁeld conditions, where no external

power sources are available.

Technical Documentation

page 2 of 5

Note: Due to the fabrication process of the SunSaver controller, the exact damaged component may

not be evident. It may only be possible to determine if the unit is functioning properly. How-

ever, other factors may be apparent the will assist the technician in determining the cause of the

failure.

Recommended Tools:

• Digital multi-meter (frequency and duty cycle measurement are helpful)

• Phillips Screwdriver

• Flat Bladed Screwdriver

• 12V/2A load (type 1156 automotive lamp with socket works well)

• Short length(6 in) of 12AWG solid wire.

Caution:

The following outlined procedures assume a basic working knowledge of electrical circuits. Ex-

ercise the necessary precautions when dealing with live electrical circuits present in solar energy

systems

Testing Procedure

Step 1: No PowerApplied to SunSaver

A) With no power applied to the SunSaver, check for short circuits to ground between the following terminals:

i) PV (+) and PV (-) terminals

ii) Battery (+) and Battery (-) terminals

iii) Load (+) and Load (-) terminals

Battery Load

+-+-

PV (+) and PV (-)

Terminals

iii

Load (+) and Load (-)

Terminals

Batt (+) and Batt (-)

Terminals

page 3 of 5

(step 1 cont.)

B) Check the LVD FET (if controller is equipped with LVD) by measuring a diode drop between Battery (+) and Load

(+) terminals. If no diode drop is present or if an open circuit is measured, the LVD FET is damaged. If no diode drop is

present (short circuit), the unit will still (most likely) regulate the battry voltage properly, however the controller will no

longer have LVD capability.

C) Check for continuity between the ground connections on the terminal strip (PV (-), Battery (-), and Load (-).

D) Remove the four screws from the face plate. Bend a small hook in one end of a 12AWG solid wire. Insert the hook

into one of the screw holes and pull off the face plate. The face place may be stuck to the internal potting and may make

a cracking sound when removed. This is normal and will not demage the internal circuitry. Inspect for burns, damaged

traces, etc.

Step 2: Battery Connected to Battery Terminals Only

Note: The green “charging” LED should be off.

A ) Measure the voltage at the battery terminals.

B) Measure the voltage at the load terminals. The voltage should be the same(+/- 200mV) as the battery voltage. If load

voltage is signiﬁcantly lower than battery voltage, LVD FET’s or the power traces inside the SunSaver are damaged.

C) Measure the voltage at the Solar (PV) terminals. The voltage should be less than 2.5 Vdc. If green LED is on, or bat-

tery voltage is measured at Solar terminals, the input FET’s are damaged and the unit will not regulate battery voltage

properly.

Step 3: PV and Battery PowerApplied to the Controller:

Note 1: The green “charging” LED should be lit

A)The voltage across the PV terminals should be the same as the

voltage across the Battery terminals if the battery is not fully

charged.

B)If the batteries are charged, there will be a voltage difference

between the PV (+) and Battery (+). If your multi-meter has a

frequency measuring option, a 300Hz AC signal should be

measured between the PV (+) and Battery (+). The duty cycle

of this signal can be used to give a rough indication of the battery

state of charge. A lower duty cycle indicates a battery with a

higher state of charge. Regulated

Power Supply

+ -

Battery Load

+-+-

Battery

page 4 of 5

Step 4: PV, Battery, and Small (2A) Load Connected to Controller

Note 1: A standard automotive brake lamp (type 1156) works well for this test.

A) with the lamp turned On, measure the Load Voltage. It should

be within 20-30 mV of the battery voltage. If the Load voltage is

more than 0.25V lower than the Battery voltage, the LVD FET’s

are damaged. Battery Load

+-+-

Battery

2A Load

Array

Step 5: SunSaver Installed in the Power System.

A) Check the correct operation of the SunSaver based on the above tests.

B) Check the condition of any fuses that might be in the power path.

C) Verify the system wiring is correct and intact.

D) Check all connections and terminals for good electrical contact.

page 5 of 5SS.APP.Field_Test.01.EN

page 5 of 5 Revision Date: 09/29/11

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Morningstar Controller Handbücher

Morningstar

Morningstar TriStar Professional TS-60M Bedienungsanleitung

Morningstar

Morningstar TriStar TS-MPPT-30 Bedienungsanleitung

Morningstar

Morningstar ProStar PS-15 Bedienungsanleitung

Morningstar

Morningstar SunSaver SS-6 Bedienungsanleitung

Morningstar

Morningstar SunLight-10 Bedienungsanleitung

Morningstar

Morningstar SHS-6 Bedienungsanleitung

Morningstar

Morningstar SUNSAVER MPPT SS-MPPT-15L Bedienungsanleitung

Morningstar

Morningstar SunSaver-10 Bedienungsanleitung

Morningstar

Morningstar PROSTAR-12 Bedienungsanleitung

Morningstar

Morningstar GenStar GS-MPPT-60 Bedienungsanleitung

Morningstar

Morningstar SunSaver MPPT Meter Map Bedienungsanleitung

Morningstar

Morningstar SUNSAVER SS-10-12V Bedienungsanleitung

Morningstar

Morningstar TriStar TS-45 Bedienungsanleitung

Morningstar

Morningstar ProStar PS-30M-PG Bedienungsanleitung

Morningstar

Morningstar EcoBoost MPPT EB-MPPT-20 Bedienungsanleitung

Morningstar

Morningstar TriStar TS-60 Bedienungsanleitung

Morningstar

Morningstar SUNSAVER MPPT SS-MPPT-15L Bedienungsanleitung

Morningstar

Morningstar ProStar MPPT Series Bedienungsanleitung

Morningstar

Morningstar Sunlight SL-10 Bedienungsanleitung

Morningstar

Morningstar TriStar TS-60M Bedienungsanleitung

Morningstar

Morningstar SUNSAVER DUO Bedienungsanleitung

Morningstar

Morningstar ProStar-15 Bedienungsanleitung

Morningstar

Morningstar TRISTAR TS-MPPT-60-600V-48-DB Bedienungsanleitung

Morningstar

Morningstar TrakStar TriStar TS-MPPT-60M Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung