Morphy Richards IB40614 Bedienungsanleitung

Your two year guarantee

It is important to retain the retailers receipt

as proof of purchase. Staple your receipt to

this back cover for future reference.

Please quote the following information if

the product develops a fault. These numbers

can be found on the base of the product.

Model no. Serial no.

All Morphy Richards products are

individually tested before leaving the factory.

In the unlikely event of any appliance proving

to be faulty within 28 days of purchase it

should be returned to the place of purchase

for it to be replaced.

If the fault develops after 28 days and

within 24 months of original purchase, you

should contact the Helpline number quoting

Model number and Serial number on the

product, or write to Morphy Richards at the

address shown. You will be asked to return

the product (in secure, adequate packaging)

to the address below along with a copy of

proof of purchase.

Subject to the exclusions set out below

(see Exclusions) the faulty appliance will then

be repaired or replaced and dispatched

usually within 7 working days of receipt.

If for any reason this item is replaced

during the 2 year guarantee period, the

guarantee on the new item will be calculated

from original purchase date. Therefore it is

vital to retain your original till receipt or

invoice to indicate the date of initial

purchase.

To qualify for the 2 year guarantee the

appliance must have been used according to

the manufacturers instructions. For example

kettles should have been regularly descaled.

EXCLUSIONS

Morphy Richards shall not be liable to

replace or repair the goods under the terms

of the guarantee where:

1The fault has been caused or is

attributable to accidental use, misuse,

negligent use or used contrary to the

manufacturers recommendations or where

the fault has been caused by power

surges or damage caused in transit.

2The appliance has been used on a voltage

supply other than that stamped on the

products.

3Repairs have been attempted by persons

other than our service staff (or authorised

dealer).

4Where the appliance has been used for

hire purposes or non domestic use.

5Morphy Richards are not liable to carry

out any type of servicing work, under the

guarantee.

6Plastic filters for all Morphy Richards

kettles and coffee makers are not covered

by the guarantee.

This guarantee does not confer any rights

other than those expressly set out above and

does not cover any claims for consequential

loss or damage. This guarantee is offered as

an additional benefit and does not affect your

statutory rights as a consumer.

• This guarantee is valid in the UK and

Ireland only.

Morphy Richards products are intended for

household use only.

Morphy Richards has a policy of continuous

improvement in product quality and design.

The company, therefore reserves the right

to change the specification of its models at

any time.

The After Sales Division

Morphy Richards Ltd, Mexborough

South Yorkshire, England, S64 8AJ

Helpline (office hours)

UK 0870 060 2615

Republic of Ireland 1800 409119

441/3752/34 Rev 3

Comfi iron 441375234 Rev 3 31/1/03 11:43 PM Page 1

Comfi-grip iron

steam/spray/shot

Please read and keep these instructions

www.morphyrichards.co.uk

getting the best from your

new iron...

• Safety first

Caution must be used when handling this appliance as it does get

very hot. Always switch off the unit and allow to cool before

cleaning or storing.

• Jet cleaning

Your iron will give the best ironing results and will last longer if you

apply jet cleaning after each period of ironing.

Comfi iron 441375234 Rev 3 31/1/03 11:43 PM Page 2

Important safety

instructions

The use of any electrical appliance

requires the following common sense safety

rules.

Primarily there is danger of injury or

death and secondly the danger of damage

to the appliance. These are indicated in the

text by the following two conventions:

WARNING: Danger to the person!

IMPORTANT: Damage to the appliance! In

addition we offer the following safety advice.

Location

• Do not use outdoors.

Children

• Children do not understand the dangers

associated with operating electrical

appliances. Never allow children to use

this appliance.

• Close supervision is necessary when any

appliance is used near children.

Personal safety

• Burns can occur from touching hot metal

parts, hot water or steam. Use caution

when you turn a steam iron upside

down, there may be hot water in the

water tank.

• Do not use the vertical steam feature on

clothes that are being worn.

• Do not leave the iron unattended whilst

plugged in or on an ironing board. Never

allow the mains lead to over hang the

work surface.

• The socket should always be off before

plugging or unplugging from the socket.

Never yank the cord to disconnect from

the socket, instead, grasp plug and pull

to disconnect.

• Do not allow the cord to touch hot

surfaces. Let the iron cool completely

before putting away. Loop cord loosely

around the iron before storing.

Other safety considerations

• Use the iron only for its intended use.

• To protect against the risk of electric

shock do not put the appliance in water

or in any other liquid.

• Always disconnect the iron from the

electrical socket when filling with water

or emptying, and when not in use.

• Do not operate the iron with a damaged

cord or if the iron has been dropped or

damaged. To avoid the risk of electric

shock, do not disassemble the iron, but

telephone Morphy Richards for advice.

Incorrect reassembly can cause a risk of

electric shock when the iron is used.

Special instructions

• If your iron does not work, check the

following points:

Has the temperature control been set to

the required temperature? Is the plug in

its socket? Is the plug itself or the socket

faulty? (Check by plugging in another

appliance).

• Warning: when not in use, your iron

should never be placed flat and left on

an ironing board.

•To prevent damage to the textile being

ironed, follow the temperature guide

carefully. (Test the inside of the hem of

the garment).

• When ironing is complete, remove the

plug from the socket, empty any

remaining water from the tank, and allow

to cool before storage.

• If you drop or severely knock your iron

this could cause internal damage even if

the outside appears alright. Have it

checked by a qualified electrician.

• It is recommended that you use up one

beaker of water by operating your iron’s

steam and shot of steam functions

before ironing any clothes as some

dripping may occur while your irons

steam system is activated.

Comfi iron 441375234 Rev 3 31/1/03 11:43 PM Page 3

Electrical requirements

Check that the voltage on the rating

plate of your appliance corresponds with

your house electricity supply which must be

A.C. (Alternating current).

If the socket outlets in your home are not

suitable for the plug supplied with this

appliance the plug should be removed and

the appropriate one fitted.

WARNING : The plug removed from

the mains lead, if severed, must be

destroyed as a plug with a bared flexible

cord is hazardous if engaged into a live

socket outlet.

Should the fuse in the 13 amp plug

require changing a 13 amp BS1362 fuse

must be fitted.

WARNING: THIS APPLIANCE MUST

BE EARTHED.

Instructions for use

Temperature guide

Heat setting markings on the adjustable control dial of all Morphy Richards irons match

those of the International Textile Care Labelling Code.

Symbol

(120˚C Max) Cool (160˚C Max) Warm (210˚C Max) Hot

Control knob

positions

Do not iron

at all

Fabric Nylon, Acetates

e.g. Acrilan

Courtelle, Orlon

Triacetates, e.g.

Tricel/Polyester

Wool, Polyester

mixtures e.g.

Polyester/Cotton

Cotton, Linen

Rayon, Rayon

mixtures,

e.g. Rayon/Linen

Ironing Iron on wrong side

if moisture required

use damp cloth

(Not Acetate)

Fabrics requiring this

setting usually require

steam pressing for heavy

cotton, denim etc.

With water in tank Dry and spray Steam/spray/shot of steam

Jet clean

Without water in tank Dry ironing

Comfi iron 441375234 Rev 3 31/1/03 11:43 PM Page 4

Components of your iron

⁄ Variable steam/steam boost control

¤ Shot of steam button

‹ Spray button

› Filling hole with cap

ﬁ Spray nozzle

ﬂSoleplate

‡ Temperature control dial with indicator

· Water tank

‚ Life long anti-scale (certain models only)

„ Temperature indicator light (red)

‰ Auto-shut off light (green)

(certain models only)

Before use

Note: The steam facility should only be

used on garments which are suitable for

ironing at the 2 and 3 dot settings.

When ironing with the steam facility at the

2 dot setting, the steam output should be set

at the lower end of the steam range (see

variable steam section).

Textiles and clothes are supposed to carry

ironing instructions. If they don’t you should

follow the fabric guide on page 3, but be sure

to test the temperature by ironing the hem of

the garment or similar area first.

If you turn the control dial down from a

hot setting to a cooler setting, wait until the

iron temperature has stabilised before you

continue ironing.

Filling

1Make sure that the iron is not plugged in

and then set the variable steam control ⁄

to the ‘0’ position before filling the iron

with water.

2Lift up the fill cap and fill the water through

the filling hole ›into the water tank ·,

using the beaker provided. AAfter filling

replace the fill cap. In hard water areas the

use of distilled or demineralised water is

recommended.

Never use battery topping up fluid or

water containing any substances like

starch, or sugar, or defrosted water

from a refridgerator.

3Always pour out the remaining water after

use. Warning: When filling your iron

with tap water always use the beaker

provided. Never fill directly under the

tap.

Temperature control

Plug in the iron and switch on. Set the

temperature control dial Bto the

temperature required, but don’t start ironing

immediately. If you wait a few minutes, the

iron will stabilise at the required setting. Your

Morphy Richards iron is fitted with an

indicator light „which will go on and off

while you are ironing.

⁄

‹

›

ﬁ

ﬂ

‡·

‚

„

‰

Comfi iron 441375234 Rev 3 31/1/03 11:43 PM Page 5

This is perfectly normal as it shows that

the iron is maintaining the heat setting you

have chosen.

It is always a good idea to begin with

cool fabrics and work up to higher settings.

An iron heats up quicker than it cools

down so you’ll save time and electricity.

Features of your iron

Temperature indicator light

The indicator light shows that the iron is

warming up. When the required

temperature is reached the light will go out

and will cycle on-off during operation.

Dry ironing

You can use your iron as a dry iron only.

Make sure the variable steam control ⁄is

set to the ‘0’ symbol.

Any temperature setting may be used

depending on the garment. The spray

feature may be used provided there is water

in the tank (see filling section). You do not

need to put any water in the tank when dry

ironing only.

Spray

Press the spray

button ‹and aim the

spray of water at

stubborn creases. You

can do this whilst dry

ironing providing there

is water in the tank.

When using the water

spray it may be

necessary to push the button a few times to

get the spray pump primed.

Variable steam

Fill the iron with water as described in

‘Filling’, page 4 and insert the plug into the

electrical socket.

The steam output can be varied from low

to high by sliding the variable steam control

C. When using the iron at the bottom of the

steam range, the steam output should be

adjusted to the lowest setting.

The steam facility should only be used

on garments which are suitable for ironing

at 2 and 3 dot setting.

Extra steam boost (certain models only)

When the variable steam slider ⁄

reaches the end of its normal

travel, pushing it further

forward creates additional

steam sometimes required to

remove difficult creases.

The slider automatically returns to

normal steam when finger pressure is

removed.

Note: For optimum performance, do not

hold the steam slider in the boost position,

release it immediately at the end of it’s

travel.

Shot of steam

Press the shot of steam

button ¤to obtain a burst of

extra steam for ironing out

creases in heavy material

such as denim etc.

The shot of steam can be used whilst dry

ironing, providing there is water in the tank,

and the temperature control is set within the

steam range.

Do not use shot of steam at

temperatures below the steam range shown

on the control.

Note: For optimum steam quality, do not

operate the shot more than three times in

succession.

higher steam

lower steam

higher steam

lower steam

Comfi iron 441375234 Rev 3 31/1/03 11:43 PM Page 6

Vertical steam

Hold the iron in a vertical position

between 1cm and 2cm away from the item

D. Press the shot of steam button ¤, this

will create vertical steam. This feature is

especially useful for removing creases from

hanging clothes, curtains, wall hangings, etc.

Note; For optimum steam quality, do not

operate the shot more than three times in

succession.

No drip system

Your iron is fitted with a no drip system

which is designed to prevent water escaping

from the soleplate when the iron is too cold.

During use, the no drip system may emit a

loud click, particularly during heat-up or

whilst cooling down. This is perfectly normal

and indicates that the system is functioning

correctly.

Auto shut-off

(certain models only)

If your iron is fitted with the auto shut-off

function it will automatically shut down after a

set period.

If the iron is left unattended in the

horizontal position it will shut down after 30

seconds.

If it is left in the vertical position it will shut

down after 8 minutes. When this happens the

green auto shut-off neon will illuminate to

show that the iron is in power-off mode.

To reactivate the iron gently shake it until

the neon goes out and wait for the iron to

heat-up as normal.

Life long anti-scale

system

(certain models only)

The life long anti-scale system reduces

scale deposits and helps prolong the life of

the iron.

Emptying and storing

When you have

finished ironing,

unplug your iron.

Ensure that the

variable steam control

is set at the ‘0’

position, lift up the fill

cap and empty any

remaining water out of

the filling hole.

Do not store in the box, but in an upright

position, so that any drops of water

remaining cannot leak out and discolour the

soleplate.

Important: The flex can be

damaged if wound too tightly

around the iron after use.

Make a loose loop with the

flex and wrap it around the

iron. The iron must be cool

before winding the flex and

storing on its heel.

Comfi iron 441375234 Rev 3 31/1/03 11:43 PM Page 7

Maintenance

Jet cleaning

Your iron has a built in cleaning system

designed to keep the water valve, steam

chamber and steam vents clear of lint and

loose mineral deposits. The ‘jet clean’ should

be operated after each period of ironing.

To operate, ensure that there is little water

in the tank, place the iron on its heel and turn

the temperature control dial to the maximum

setting. Wait for the temperature indicator

light to go out, then unplug the iron and hold

it about 6’’ (150mm) above the sink in the

ironing position. Press the shot of steam

button about 10 times in succession.

After this cleaning operation, empty out

any remaining water.

To clean a stainless steel

or anodised soleplate

(certain models only)

To keep the soleplate of your iron clean

and free of limescale, we recommend that

you use one of the gentle chrome, silver or

stainless steel cleaners that are generally

available. Always follow the manufacturers

instructions. To clean off melted man-made

fibres set the iron at 3 dot position and pass

it over a clean piece of cotton which will draw

the deposit off the surface.

To clean a coated soleplate

(certain models only)

In the unlikely event of any man-made

fibre fusing to the soleplate, set the iron at

the 3 dot position and pass it over a clean

piece of cotton which will draw the deposit

off the surface.

Do not use scouring powder or solution as

this could cause damage to the coating.

To clean the exterior

Allow the iron to cool and wipe over with a

damp cloth and mild detergent, then wipe

with a dry cloth.

Helpline

If you have any difficulty with your

appliance, do not hesitate to call us.

We are more likely able to help than the

store from where you bought it.

Please have the following information

ready to enable our staff to deal with your

query quickly.

• Name of the product

• Model number as shown on the underside

of the appliance.

Comfi iron 441375234 Rev 3 31/1/03 11:43 PM Page 8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Morphy Richards Eisen Handbücher

Morphy Richards

Morphy Richards Power SteamPro Bedienungsanleitung

Morphy Richards

Morphy Richards 40707 Bedienungsanleitung

Morphy Richards

Morphy Richards IB4070X Bedienungsanleitung

Morphy Richards

Morphy Richards Steam Generator ironing system Bedienungsanleitung

Morphy Richards

Morphy Richards SPEED STEAMPRO Bedienungsanleitung

Morphy Richards

Morphy Richards TURBOSTEAM 40659 Bedienungsanleitung

Morphy Richards

Morphy Richards Atomist Bedienungsanleitung

Morphy Richards

Morphy Richards TURBOSTEAM IRON - MANUAL 2 Bedienungsanleitung

Morphy Richards

Morphy Richards Comfigrip Advanced 40741 Bedienungsanleitung

Morphy Richards

Morphy Richards VAPOCARE Bedienungsanleitung

Morphy Richards

Morphy Richards breeze Bedienungsanleitung

Morphy Richards

Morphy Richards Saturn IntelliTemp 305003 Bedienungsanleitung

Morphy Richards

Morphy Richards RN40868 Bedienungsanleitung

Morphy Richards

Morphy Richards TURBOSTEAM IRON RN40514 MUK REV 1 Bedienungsanleitung

Morphy Richards

Morphy Richards IB42270 Bedienungsanleitung

Morphy Richards

Morphy Richards TURBOSTEAM 40659 Bedienungsanleitung

Morphy Richards

Morphy Richards JET STREAM ELITE+ - AUTRE Bedienungsanleitung

Morphy Richards

Morphy Richards Cruiser Bedienungsanleitung

Morphy Richards

Morphy Richards COMFIGRIP Bedienungsanleitung

Morphy Richards

Morphy Richards Power Steam Bedienungsanleitung

Morphy Richards

Morphy Richards Semi-electronic iron Bedienungsanleitung

Morphy Richards

Morphy Richards POWER STEAMELITE Bedienungsanleitung

Morphy Richards

Morphy Richards 40684 Bedienungsanleitung

Morphy Richards

Morphy Richards Power Steam Bedienungsanleitung

Beliebte Eisen Handbücher anderer Marken

Clatronic

Clatronic DB 3703 Bedienungsanleitung

TEFAL

TEFAL FV4093Z0 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 BS Bedienungsanleitung

Philips

Philips GC6012 Bedienungsanleitung

Bosch

Bosch 2 Series Bedienungsanleitung

Riffel

Riffel Catena KB-819 Bedienungsanleitung

Texi

Texi Hestia Bedienungsanleitung

Maxwell

Maxwell MW-3010 Bedienungsanleitung

TREVIDEA

TREVIDEA Girmi ST60 Bedienungsanleitung

Philips

Philips HI5914/30 Bedienungsanleitung

Primula

Primula Vapormat Bedienungsanleitung

Magio

Magio MG-541 Bedienungsanleitung

Scarlett

Scarlett SC-1334S Bedienungsanleitung

Bosch

Bosch Sensixx B22L Bedienungsanleitung

Philips

Philips GC651 Bedienungsanleitung

Vitek

Vitek VT-1247 VT Bedienungsanleitung

Cleanmaxx

Cleanmaxx 3397 Bedienungsanleitung

Philips

Philips GC800 Bedienungsanleitung