Morphy Richards IB421XX Bedienungsanleitung

Two year guarantee

This guarantee is valid in the UK and Ireland

only. It is in your interest to retain the retailers receipt

as proof of purchase. Please quote the following

information if the product develops a fault. These

numbers can be found on the base of the product.

Model No. Serial No.

All Morphy Richards products are individually tested

before leaving the factory. In the unlikely event of any

appliance proving to be faulty within 28 days of

purchase it should be returned to the place of purchase

for it to be replaced.

If the fault develops after 28 days and within 24

months of original purchase, you should contact the

Helpline number quoting Model number and Serial

number on the product, or write to the address below.

You will be asked to return the product (in secure,

adequate packaging) to the address below along

with a copy of proof of purchase. Subject to the

exclusions set out below (see ‘Exclusions’) the faulty

appliance will then be repaired or replaced and

dispatched usually within 7 working days of receipt.

If for any reason this item is replaced during the 2

year guarantee period, the guarantee on the new

item will be calculated from original purchase date.

Therefore it is vital to retain your original till receipt or

invoice to indicate the date of initial purchase.

To qualify for the 2 year guarantee the appliance

must have been used according to the

manufacturers instructions. For example kettles

should have been regularly descaled or an iron cord

should have been stored as recommended by the

instructions.

EXCLUSIONS

Morphy Richards shall not be liable to replace

or repair the goods under the terms of the

Guarantee where:

1 The fault has been caused or is attributable to

accidental use, misuse, negligent use or used

contrary to the manufacturers recommendations

or where the fault has been caused by power

surges or damage caused in transit.

2 The appliance has been used on a voltage

supply other than that stamped on the

products.

3 Repairs have been attempted by persons other

than our service staff (or authorised dealer).

4 Where the appliance has been used for hire

purposes or non-domestic use.

5 Morphy Richards are not liable to carry out any

type of servicing work, under the guarantee.

6 Plastic filters for all Morphy Richards kettles

and coffee makers are not covered by the

guarantee.

This guarantee does not confer any rights other

than those expressly set out above and does not

cover any claims for consequential loss or damage.

This guarantee is offered as an additional benefit

and does not affect your statutory rights as a

consumer.

The After Sales Division, Morphy Richards Ltd, Mexborough, South Yorkshire, England, S64 8AJ

Helpline (office hours ): UK (local rate) 08450 777700, Republic of Ireland 1800 409119

Steam/Spray/Shot Mirage irons

Important safeguardsImportant safeguards

Important safeguards

When using your iron, basic safety

precautions should always be followed,

including the following:

1Read all the instructions.

2Use the iron only for its intended use.

3To protect against the risk of electric

shock do not put the appliance in

water or in any other liquid.

4Close supervision is necessary when

any appliance is used near children.

NEVER ALLOW A CHILD TO USE

THIS PRODUCT.

5The socket should always be off

before plugging or unplugging from

the socket. Never yank the cord to

disconnect from socket, instead,

grasp plug and pull to disconnect.

6Do not allow cord to touch hot

surfaces. Let iron cool completely

before putting away. Loop cord loosely

around the iron before storing.

7Always disconnect the iron from the

electrical socket when filling with water

or emptying, and when not in use.

8Do not use outdoors.

9Do not operate the iron with a

damaged cord or if the iron has been

dropped or damaged. To avoid the risk

of electric shock, do not disassemble

the iron, but telephone Morphy

Richards for advice. Incorrect

reassembly can cause a risk of

electric shock when the iron is used.

10Do not use the vertical steam feature

on clothes that are being worn.

11 Do not leave the iron unattended

whilst plugged in or on an ironing

board. Never allow the mains lead to

over hang the work surface.

12Burns can occur from touching hot

metal parts, hot water or steam. Use

caution when you turn a steam iron

upside down, there may be hot water

in the water tank.

Special instructionsSpecial instructions

Special instructions

1If your iron does not work, check the

following points:

Has the temperature control been set

to the required temperature? Is the

plug in its socket? Is the plug itself or

the socket faulty? (Check by plugging

in another appliance).

2 Warning : When not in use, your iron

should never be placed flat and left

on an ironing board.

3To prevent damage to the textile being

ironed, follow the temperature guide

carefully. (Test the inside of the hem of

the garment).

4When ironing is complete, remove the

plug from the socket, empty any

remaining water from the tank, and

allow to cool before storage.

5If you drop or severely knock your iron

thiscould cause internal damage even

if the outside appears alright. Have it

checked by a qualified electrician.

6It is recommended that you use up

onebeaker of water by operating your

iron’s steam and shot of steam

functions before ironing any clothes as

some dripping may occur while your

iron’s steam system is activated.

SAVE THESESAVE THESE

SAVE THESE

INSTR CTIONSINSTR CTIONS

INSTR CTIONS

Electrical requirementsElectrical requirements

Electrical requirements

Check that the voltage on the rating plate of

yourappliancecorresponds with yourhouse

electricity supply which must be A.C.

(Alternatingcurrent).

If the socket outlets in your home are not

suitable for the plug supplied with this appliance

theplugshouldberemoved and the appropriate

onefitted.

IMP0RTANT:THEPLUG REMOVED FROM

THE MAINS LEAD, IF SEVERED, MUST BE

DESTROYEDAS A PLUG WITH A BARED

FLEXIBLECORD ISHAZARDOUSIF

ENGAGEDINTOALIVESOCKETOUTLET.

Shouldthe fuse in the 13 amp plug require

replacement, a 13 amp BS1362 fuse must be

fitted.

WARNING : THIS APPLIANCE MUST BE

EARTHED.

Temperature guide

Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the

internationalTextile CareLabellingCode.

Symbol

Control knob

positions

Fabric

Ironing

With water in tank

Without water in tank

(120o CMax)Cool (160o CMax)Warm (210o C Max) Hot

Do not iron

at all

Nylon, Acetates

e.g. Acrilan

Courtelle, Orlon

Triacetates, e.g.

Tricel/Polyester

Wool, polyester

mixtures e.g.

Polyester/Cotton

Cotton, linen

Rayon, Rayon

mixtures,

e.g. Rayon/Linen

Iron on wrong side.

If moisture required

use damp cloth

(Not Acetate)

Fabrics requiring this

setting usually require

steam pressing for

heavy cotton, denim

etc

Dry and

spray Steam/spray/

shot of steam

Dry ironing

Instructions for useInstructions for use

Instructions for use

Components of your ironComponents of your iron

Components of your iron

Spraybutton

Shot of steam button

Variablesteamcontrol

Fillinghole

Spraynozzle

Soleplate

Temperaturecontroldial

Water tank

Temperatureindicatorlight

anddialpointer

Before useBefore use

Before use

Note : The steam facility should only be used

ongarments whichare suitablefor ironingat the

3 dot setting.

Textiles and clothes are supposed to carry

ironing instructions. If they don’t you should

follow the fabric guide on the rear of the iron, but

be sure to test the temperature by ironing the

hem of the garment or similar area first.

If you turn the control dial down from a hot

setting to a cooler setting, wait until the iron

temperaturehasstabilised before youcontinue

ironing.

FillingFilling

Filling

1Make sure that the iron is not plugged in and

then set the variable steam control to the

“0” position beforefilling the iron with water.

2Fill the water through the filling hole into

the water tank , using the beaker

provided. Inhard water areas theuse of

distilledor demineralised wateris

recommended.

Never use battery topping-up fluid or

water containing any substances like

starch or sugar, or defrosted water from a

refrigerator.

3Alwayspour out theremainingwater after

use.

WARNING : When filling your iron with

tap water always use the beaker

provided. Never fill directly under the

tap.

Temperature controlTemperature control

Temperature control

Plug in the iron and switch on. Set the

temperaturecontrol dial tothe temperature

required,but don’t startironing immediately. If

you wait a few minutes, the iron will stabilise at

therequired setting. YourMorphy Richardsiron

is fitted with an indicator light which will go

on and off while you are ironing. This is perfectly

normal as it shows that the iron is maintaining

the heat setting you have chosen.

It is always a good idea to begin with ‘cool’

fabrics and work up to higher settings.

An iron heats up quicker than it cools down

so you’ll save time and electricity.

Features of your ironFeatures of your iron

Features of your iron

Temperature indicator light

The indicator light shows that the iron is

warmingup.When the requiredtemperatureis

reached the light will go out and will cycle on-off

duringoperation.

Dry ironing

You can use your iron as a dry iron only.

Make sure the variable steam control is set

to the “0” symbol.

Any temperature setting may be used

dependingonthegarment. The spray feature

may be used provided there is water in the tank

(see filling section). You do not need to put any

water in the tank when dry ironing only.

Spray

Press the spray button and aim the spray

of water at stubborn creases. You can do this

whilstdry ironing providingthere is waterin the

tank. When using the water spray it may be

necessary to push the button a few times to get

thespray pump primed.

Variable Steam

Fill the iron with water as described in

“Filling”, page 4 and insert the plug into the

electrical socket.

Turn the temperature control dial , to the

“steam” position shown as and rest the iron

on it’s heel whilst it warms up.

Turnthe variable steamcontrol to give the

desired amount of steam .

The steam facility should only be used on

garments which are suitable for ironing at the 3

dot setting.

Shot of steam

Press the shot of steam button to obtain

a burst of extra steam for ironing out creases

in heavy material such as denim etc.

The shot of steam can be used whilst dry

ironing, providing there is water in the tank,

and the temperature control is set to the steam

position.

Do not use shot of steam at temperatures

below the steam position shown on the

control.

Note : For optimum steam quality, do not

operate the shot more than three times in

succession.

Vertical steam

(certain models only)

Hold the iron in a vertical position between

1 cm and 2 cm away from the item. Press the

shot of steam button , this will create

vertical steam. This feature is especially useful

for removing creases from hanging clothes,

curtains, wall hangings, etc.

No drip system (certain models only)

Your iron is fitted with a no drip system

which is designed to prevent water escaping

from the soleplate when the iron is too cold.

During use, the no drip system may emit a

loud click, particularly during heat-up or whilst

cooling down. This is perfectly normal and

indicates that the system is functioning

correctly.

Emptying and StoringEmptying and Storing

Emptying and Storing

Whenyouhavefinished ironing, unplug your

iron.Ensure that thevariable steam control

is set at the “0” position and empty any

remaining water out of the filling hole .

Do not store in the box, but in an upright

position, so that any drops of water remaining

cannot leak out and discolour the soleplate.

Important: The flex canbe damaged ifwound

too tightly around the iron after use. Make a

loose loop with the flex and wrap it around the

iron.The iron mustbe cool beforewinding the

flex and storing on its heel.

MaintenanceMaintenance

Maintenance

Self cleaning

Your iron will give the best ironing results and

lastlonger if you apply “self-cleaning”once a

month to remove any scale, fluff etc.

Fill the iron as described in the section of

‘How to fill water’. Fill the water tank up to half

full. Place the iron on a flat surface in a

standingposition.

Connect to a mains supply outlet.

Turnthe temperaturedial ina clockwise

direction to the maximum setting. When the

temperatureindicator light goes offfor the

second time, turn the temperature dial in an anti-

clockwise direction to ‘min’.

Disconnect the iron from the mains outlet

and hold the iron horizontally over a sink. Push

and hold the variable steam control dial to the

self cleaning position.

Steam and boiling water will emit from the

holes on the soleplate washing away scale and

mineral deposits in the steam chamber. Gently

movethe iron back andforward until thewater

tank is empty. When the self cleaning is

complete,release the variablesteamcontrol.

To clean the stainless steel soleplate

(certain models only)

To keep the soleplate of your iron clean and

free of limescale, we recommend that you use

one of the gentle chrome, silver or stainless

steel cleaners that are generally available.

Always follow the manufacturers instructions.

To clean off melted man-made fibres set the

iron at 3 dot position and pass it over a clean

piece of cotton which will draw the deposit off

the surface.

To clean a coated soleplate

(certain models only)

In the unlikely event of any man-made fibre

fusing to the soleplate, set the iron at the 3 dot

position and pass it over a clean piece of

cotton which will draw the deposit off the

surface.

Do not use scouring powder or solution as

this could cause damage to the coating.

To clean the exterior

Allow the iron to cool and wipe over with a

damp cloth and mild detergent, then wipe with

a dry cloth.

MorphyRichardsproducts are intended forhouseholduse only.

MorphyRichards has apolicy of continuousimprovement in product qualityand design.

The Company, therefore, reserves the right to change the specification of its models at any time.

Morphy Richards Limited, Mexborough,

South Yorkshire, England, S64 8AJ 441/3752/16 Rev 1

Inhaltsverzeichnis

Andere Morphy Richards Eisen Handbücher

Morphy Richards

Morphy Richards SPEED STEAMPRO Bedienungsanleitung

Morphy Richards

Morphy Richards COMFIGRIP Bedienungsanleitung

Morphy Richards

Morphy Richards ELITE 42288 Bedienungsanleitung

Morphy Richards

Morphy Richards Comfigrip Advanced 40715 Bedienungsanleitung

Morphy Richards

Morphy Richards RN42271MUK Bedienungsanleitung

Morphy Richards

Morphy Richards Comfigrip 300007 Bedienungsanleitung

Morphy Richards

Morphy Richards NO MODEL NO NUMBER Bedienungsanleitung

Morphy Richards

Morphy Richards JET STREAM Bedienungsanleitung

Morphy Richards

Morphy Richards Power Steam Bedienungsanleitung

Morphy Richards

Morphy Richards IB40310 Bedienungsanleitung

Morphy Richards

Morphy Richards 40734 Bedienungsanleitung

Morphy Richards

Morphy Richards IB42370 Bedienungsanleitung

Morphy Richards

Morphy Richards RN40655 Bedienungsanleitung

Morphy Richards

Morphy Richards IB4050X Bedienungsanleitung

Morphy Richards

Morphy Richards Jet Stream Series Bedienungsanleitung

Morphy Richards

Morphy Richards SEMI-ELECTRONIC 40715 Bedienungsanleitung

Morphy Richards

Morphy Richards TURBOSTEAM IRON - MANUAL 2 Bedienungsanleitung

Morphy Richards

Morphy Richards Turbo steam iron Bedienungsanleitung

Morphy Richards

Morphy Richards breeze Bedienungsanleitung

Morphy Richards

Morphy Richards Jet Steam 333024 Bedienungsanleitung

Morphy Richards

Morphy Richards Turbosteam Bedienungsanleitung

Morphy Richards

Morphy Richards IB42410 Bedienungsanleitung

Morphy Richards

Morphy Richards breeze Bedienungsanleitung

Morphy Richards

Morphy Richards TURBOSTEAM IRON RN40514 MUK REV 1 Bedienungsanleitung

Beliebte Eisen Handbücher anderer Marken

Clatronic

Clatronic DB 3703 Bedienungsanleitung

TEFAL

TEFAL FV4093Z0 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 BS Bedienungsanleitung

Philips

Philips GC6012 Bedienungsanleitung

Bosch

Bosch 2 Series Bedienungsanleitung

Riffel

Riffel Catena KB-819 Bedienungsanleitung

Texi

Texi Hestia Bedienungsanleitung

Maxwell

Maxwell MW-3010 Bedienungsanleitung

TREVIDEA

TREVIDEA Girmi ST60 Bedienungsanleitung

Philips

Philips HI5914/30 Bedienungsanleitung

Primula

Primula Vapormat Bedienungsanleitung

Magio

Magio MG-541 Bedienungsanleitung

Scarlett

Scarlett SC-1334S Bedienungsanleitung

Bosch

Bosch Sensixx B22L Bedienungsanleitung

Philips

Philips GC651 Bedienungsanleitung

Vitek

Vitek VT-1247 VT Bedienungsanleitung

Cleanmaxx

Cleanmaxx 3397 Bedienungsanleitung

Philips

Philips GC800 Bedienungsanleitung