MorrHeat MHB280 Handbuch

Installation, operation and service instructions

120v Manual

Waste Oil Fired Boiler 280-480

2MorrHeat - Most Heat In The Industry - Rev 3/18/2019

Table of Contents

Table of Contents Page 2

Important Information Page 3

Notice Page 4

Burner & Pump Specications Page 5

Product Description Page 7

Inspect Shipment Page 8

Before Install Page 9

Boiler Room Air Requirment Page 10

Venting Installation Page 13

Fuel Supply Lines Page 14

Boiler Assembly & Wiring Page 16

Boiler Assembly & Installation Page 22

Oil Burner Technology Page 23

Oil Burner Components Page 24

References (Nozzle|Electrode|Burner & Pump) Page 26

Boiler Start-up & Adustments Page 27

Filling Boiler Page 28

Burner Startup - All Fuels Page 29

Prevention Page 30

Initial Start Procedure Page 31

Maintenance Page 32

Attention Page 34

Troubleshooting Page 35

Jacket Attachment Page 38

Parts List Page 40

Exploded View Page 41

Warranty Information - 10 Year Page 42

3MorrHeat - Most Heat In The Industry - Rev 3/18/2019

Important Information

Taking Delivery of Equipment:

When taking delivery of your equipment, please be sure to check the shipment for any

potential damages (MorrHeat is not responsible for any damaged shipments if signed for

non-damaged). If any damage is identied upon delivery, either sign for as damaged goods

specically noting in detail the apparent damage / or / refuse the shipment completely and

be sure to le a claim with the shipping company immediately regardless of the damage.

Waste oil contains various unknown materials and may also contain random amounts

of gasoline or other volatile fuels. Specic safety and handling precautions should be

considered when cleaning, maintaining and operating waste oil boilers.

It is recommended to use a lter or some kind of strainer when pouring waste oils into the storage tank(s).

This will increase chances of catching any particulates prior to the pump lter(s) to insure a cleaner fuel

source.

WARNING:

Waste oil boilers should not be used in any hazardous areas that may contain ammable or

volatile vapors or even combustible dusts. It is not recommended to use a waste oil boilers in

any areas that may have chlorinated or similar chemical vapors. This will cause deterioration

& corrosion of the metals the equipment is constructed of (this would void the warranty).

Antifreeze does not burn and will interrupt the performance of the unit and potentially shut

down completely until re-primed and restarted. If too much antifreeze is present just like

water, the unit will not re. Do not expose units to water, moisture or rain. This is an inside

unit, not designed for outdoor use.

Oils and different Viscosities that can be burnt, but not limited to:

*Used Motor Oils *Transmission Fluid *Hydraulic Fluids *Diesel Fuels

Do not use old contaminated oils or fuels and keep in mind underground tanks and outdoor

oil storage could have unknown amounts of water and moisture, outside barrels will leak

water and moistures through the bunghole.

IMPORTANT:

The instructions and information within this manual are provided to remind you of any

warnings and to assure you have properly and successfully setup the equipment purchased.

The information is also intended to help the end user/installer be aware of the operations

and service required for optimal performance. These boilers are recommended for primary

or an auxiliary source of heat but are not recommended for use as the sole source of heat

in case of any expected or unexpected downtime with the unit. If a steady supply of fuel is

not present or interrupted at the burner unit, the burner unit will shut down. Be prepared

with an alternate source of heat to insure the building and all pipes are not at risk of freezing

temperatures.

4MorrHeat - Most Heat In The Industry - Rev 3/18/2019

To insure the best performance, optimal efciencies and heat output of the heating unit, it is

recommended and necessary to become familiar with your unit and the procedures needed

with initially starting, running, cleaning and maintaining the heating unit.

It is important to remember when burning used or dirty oils that contaminants could be

present. Because of various contaminates, be aware of needing to change lters when

needed. Keep the chamber and heat exchanger(s) passageways clean. Make sure the fuel

pump is primed and lines are free of any debris, air bubbles or interuptions.

Draft is just as important as the rest; bad draft can cause serious problems and not allow the

gasses within the unit to correctly leave the heating unit. Correct draft is needed for optimal

performance. Bad draft will cause over-re or overheating due to bottling up the heat or

creating back pressure back in to the heating unit. If black smoke is present, bad draft, bad

combustion or both is occuring.

Notice

5MorrHeat - Most Heat In The Industry - Rev 3/18/2019

Voltage -120 v

Cycles -60Hz

Total Operating Amperage (Burner Only) Amp 8.4

Total Operating Amperage (Burner & Oil Pump) Amp 10.5

Electrical Operating Consumption (Burner Only) Watts 970

Electrical Operating Consumption (Burner & Oil Pump) Watts 1, 212

Weight Lbs 36.5

Oil Primary Amp 0.2

Oil Valve Amp 0.075

Pre-Heater Block Amp 4.2

Pre-Heater Controller Board Amp 0 . 011

Igniter Transformer Amp 0.3

Burner Motor Amp 3.6

Voltage -120 v

Cycles -60Hz

Total Operating Amperage (Pump Assy Only) Amps 2.1

Electrical Operating Consumption (Pump Assy Only) Watts 241.5

Weight Lbs 16

Oil Valve Amps 0.075

Pump Motor Amps 2.0

BURNER ASSEMBLY

PUMP ASSEMBLY

Performance Ratings

Burner &Pump Specifications

6MorrHeat - Most Heat In The Industry - Rev 3/18/2019

SPECIFICATIONS - DIMENSIONS TABLE 1

Boiler

Model

OIL

GPH

APPROX.

DRY

WEIGHT

LBS.

Vent

Connect

DIA"

I-B-R

VENT

DIA" DIM"

WATER

CONTENT

GAL.

MHB280 2.0 1301 10 842 22.2

MHB360 2.5 1654 10 10 52 28.5

MHB480 3.0 1831 10 10 57 31.7

Note: All dimensions are inches

* Gross I-B-R rating has been determined under the I-B-R provisions governing forced draft conditions (0.10 inch W.C

positive pressure at the boiler ue gas outlet.

** Net ratings are based on piping and pickup allowance 1.15.

*** I-B-R Vent Diameter size is the pipe size used from boiler vent connector F to Termination of stub stack: Max Height

15' (For forced draft ring only). For chimney venting consult National Fuel Gas Code.

CENTERLINE OF

BURNING PLATE

OBSERVATION

PORT

FRONT RIGHT REAR

2 - 1/2" M.P.T SUPPLY CONNECTION

2 - 1/2" F.P.T RETURN

CONNECTION

29- 1/2"

20"

C. O. PORTS

9 - 3/8"

36"

17"

33"

7MorrHeat - Most Heat In The Industry - Rev 3/18/2019

The MHB Series boilers are a three pass Scotch Marine design, with fully water backed heat

transfer surfaces. Boilers are designed for use in forced hot water heating systems up to 75

PSI water working pressure. They may be used with burners ring gas or oil. Boiler-Burner

units operate with a positive pressure overre and may be vented using a conventional

chimney with a balanced draft or pressurized vent systems.

The boiler block (heat exchanger) is factory assembled using cast iron push nipples. This

heat exchanger has horizontal ue passages through which the products of combustion

make three distinct passes to maximize the heat transfer process.

Product Description

8MorrHeat - Most Heat In The Industry - Rev 3/18/2019

Inspect Shipment

Any claims for damage or shortage must be led immediately against the carrier by the

consignee. No claims for variances from, or shortage in orders, will be considered unless

presented within 7 days after receipt of goods. Boiler shipment comes on two separate

pallets.

NOTE :Burner, when ordered, is shipped separately

1. Wood pallet with:

A. Boiler block with bafes installed in ue passages.

2. Wood pallet with shrink wrapped boxes:

A. Box of jacket parts.

B. Box marked #1 (Manifold Box)

a. Supply and return manifold with gaskets, mounting studs, nuts and

and washers.

b. Return diffuser and gaskets.

c. (2) 3/4" Make x Female extensions coupling for optional controls.

C. Box marked #2 (Control Box)

a. L4008A Hi-Limit with 3/4" well and capalary clip.

b. Tridicator Gauge

c. Relief Valve

d. Bag of refractory mix to insulate burner blast tube in front door.

e. Instruction manual

f. Boiler rating tag and A.S.M.E. Tag

g. Flame Sight Assembly

h. (4) Spacers to secure back jacket panel.

D. Box marked #3

a. Quadrant locking damper

9MorrHeat - Most Heat In The Industry - Rev 3/18/2019

Before Install

CODE REQUIREMENTS:

Installation must comply with all state, local and utility codes. When required, the installation

must conform to A.S.M.E. safety code for controls and safety devices for automatically red

boilers No. CSD-1.

RULES FOR SAFE INSTALLATION AND OPERATION:

1. Read this owner's manual and the rules for safe operation carefully. Failure to follow the

rules for safe operation and the instructions could cause a malfunction of the boiler and

result in depth, serious bodily injury, and/or property damage.

2. Be certain burner is designed for the type of fuel to be used. Overring will result in

premature failure of the boiler sections and cause dangerous operation.

3. Locate the boiler as close to the chimney as practical (See Fig. 1,2,3)

Observe the minimum clearances outlined in (Fig. 1). Remember to allow room for the boiler

door to open with the burner mounted.

4. Make sure that the surface on which the boiler is to be installed is capable of supporting

the weight of the boiler, burner, and all other equipment supported by the surface.

5. A boiler pad is strongly recommended (see Fig. 1). This pad is to be made of poured

concrete. It should be at least 4 inches thick and should cover the entire area under the

boiler (not just under the legs).

6. Make sure that the location chosen for the boiler will provide adequate air for combustion

and ventilation (See Fig. 2). Also make sure that fuel and electrical requirements can be

satised at the boiler location chosen.

7. For typical boiler/heating system piping which incorporates a blending pump, or for

primary secondary pumped system See Fig. 4, 5, 6.

8. The heating system design shall not permit the boiler's return water temperature to be

lower than 130℉ for a signicant period of time. This will prevent reside corrosion and

10MorrHeat - Most Heat In The Industry - Rev 3/18/2019

Boiler Room Air Requirment

WARNING

Failure to provide an adequate supply of fresh air for combustion will result in

hazardous operating conditions. Do not use an exhaust fan in the boiler room.

1. To ensure safe, efcient operation, the boiler system must be supplied with sufcient air for

combustion and ventilation. (See Fig. 2)

2. Unless properly controlled, avoid the use of forced ventilation, since it can create an undesirable

pressure differential between boiler room and air source.

3. All boilers located in conned rooms should have free access to ventilation and combustion air

from two permanent opening. One opening should terminate within 12" of the ceiling , the other 12"

of the oor. Each opening shall have at least 1 sq. inch free area per 1,000 btn/hr. of burner input.

Opening should freely connect with areas having adequate inltration of outside air.

When air comes directly from outdoors, again use two openings as explained above, except:

• Direct connection or vertical ducting allow 1 sq. inch per 4,000 btu/hr.

• Direct connection through horizontal ducting allow 1 sq. inch per 2,000 btu/hr.

• All ducting shall be the same size as opening but no less than 3 x 3 or 9 sq. inches.

Remember to compensate for louver blockage when calculating free air. Refer to the manufacturer's

instructions or use the general guild:

WOOD LOUVERS allow 20-25% free air, METAL LOUVERS or GRILLES allow 60%-70% free air. Any

louvers dampers should lock open or interlock with the burner to open autiomatically when the

boiler operates.

FIG. 2 | RECOMMENDED BOILER ROOM VENTILATION & COMBUSTION AIR

Chimney

Boiler

12"

Louvered Openings

For Ventilation &

Combustion Air

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MorrHeat Kessel Handbücher

MorrHeat

MorrHeat MHB80 Handbuch

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung