4
PROPER USE
For safety reasons, the Brushcutters are not to be used by
children, young people under 16 years of age, or any other
persons who are not acquainted with these directions for use.
Specific safety information Please read this safety
information and the directions for use carefully and be
sure to follow the instructions to the letter.
1. This machine should never be used
for anything other than the purpose for
which it has been designed.
2. Do not use this brush cutter when tired
or drowsy or under the influence of
medication or alcohol, or at any time
when you may not be able to operate it
safely.
3. Avoid running the engine indoors. The
exhaust gases contain harmful carbon
monoxide.
4. Never use the machine in the circumstances described below:
- When the ground is slippery or when other conditions
exist which might make your footing unsteady.
- At night or in times of fog where it would not be possible
to have a clear view of the cutting area.
- During rain or electrical storms, during gale force winds
or at any time when weather conditions might make use
of the product unsafe.
5. Before using this product for the first time, get an experienced
operator to show you how to use the machine.
6. When you are new to the machine, limit your work sessions
to 30-40 minutes with a 10 minute break between, and a total
working time of 2 hours per day. Accidents can be caused by
tiredness and physical exhaustion.
7. Be sure to keep this manual handy so that you may refer to it
later if any questions arise.
8. Always be sure to include this manual when selling, or lending,
this machine.
9. Never allow children or anyone to use this machine if they
cannot fully understand the directions given in this manual.
SAFETY PRECAUTIONS
1. Before beginning work, check the worksite carefully to see
whether there are any obstacles to be removed or avoided and
whether there are any potholes or obstructions which might
cause you to lose your footing.
2. The area within a radius of 15m of the brush cutter should be
considered a hazardous area into which no one should enter
while the brush cutter is in use. If necessary, yellow warning
rope or warning signs should be placed around the work area.
When work is to be performed simultaneously by two or more
persons, constantly be aware of the location of other operators
to maintain a safe separation distance.
3. Make sure that there are no loose screws or bolts, fuel leaks
or any other problems, which might result in unsafe operation.
Be especially careful to check the blades and their fastening
arrangements.
4. Never use blades that are bent, warped, cracked, broken or
damaged in any way.
5. Always keep metal blades sharp
by filing the cutting edges,
particularly at the outer ends.
There should be a radius at the
inside end of the cutting edge.
6. Check the blade fastening bolt and be sure the blade turns
smoothly without abnormal noise.
Proper safety precautions must be observed. Like all power
equipment this unit must be handled carefully. DO NOT EXPOSE
YOURSELF OR OTHERS TO DANGER Follow these general rules.
Do not permit others to use this machine unless they are thoroughly
responsible and have read, and understand the machine manual
and are trained in its operation. This machine is not to be operated
by children.
• Always use proper handles and shoulder strap when cutting
• Do not mix fuel in an enclosed room or near open flames.
Ensure adequate ventilation
• Never remove the fuel tank cap while the engine is running
• Never start or run the engine inside a closed room or building
Fumes from the exhaust contain dangerous carbon monoxide
• Never attempt to make engine adjustments while the unit is
running and strapped to the operator. Always make engine
adjustments with the unit resting on a flat, clear surface
• Do not lift the machine other than by the handle of the shaft
• Do not use the unit if it is damaged or poorly adjusted. Never
remove the machine’s guard. Serious injury to the operator or
bystanders could result as well as damage to the machine
• Keep children away. Onlookers should be kept at a safe
distance from the work area, at least 15 METER( 50 FEET)
• Do not overreach. Keep proper footing and balance at all times.
Do not run the unit while standing on a ladder or on any other
unstable footing location
• Do not use the unit when you are tired, ill or under the influence
of medication, drugs or alcohol
• Use nylon cutting head which is free of damage. If a stone or
any other obstacle is hit, stop the engine and check the nylon
cutting head. A broken or unbalanced nylon cutting head must
never be used.
FOLLOW INSTRUCTION FOR CHANGING ACCESSORIES
• Never touch the nylon cutting head when ever the engine
is running. If it is necessary to adjust the protector or nylon
cutting head, be sure to stop the engine and confirm that the
nylon cutting head has stopped running
• The engine should be turned off when the machine is moved
between work areas
• Be careful not to hit the nylon cutting head against stones, or
the ground. Unreasonable rough operation will shorten the life
of the machine as well as create an unsafe environment for
yourself and those around you
• Pay special attention to operation in the rain or just after the
rain as the ground may be slippery
• When the machine is placed in storage for a long time, drain
fuel from the fuel tank and carburetor, clean the parts, move
the machine to a safe place and confirm that the engine is
cooled down
• It is believed that a condition called Raynaud’s phenomenon,
which affects the fingers of certain individuals may be brought
about by exposure to vibration and cold. Exposure to vibration
and cold may cause tingling and burning sensations followed
by loss of color and numbness in the fingers. The following
precautions are strongly recommended because the minimum
exposure which might trigger the ailment is unknown.
Keep your body warm, especially the head, neck, feet,
ankles, hands and wrists. Maintain good blood circulation by
performing vigorous arm exercises during frequent work breaks
and also by not smoking.
Limit the hours of operation. Try to fill each day with jobs where
operating the brush cutter or other hand-held power equipment
is not required.
