Morse 185M Series Bedienungsanleitung

Operator’s Manual for

MORSE 185M Series Kontrol-Karriers with Spark Resistant Parts

Serial # 0188 - 0407

185A-M for 55 gal. standard steel drums (22 ½” diameter)

185B-M for 30 gal. standard steel drums (19” diameter)

185C-M for steel or fibre drums (21 - 23” diameter)

185D-M for steel or fibre drums (19 - 20 ½” diameter)

The letter M designates “Made with spark resistant parts.”

A. IMPORTANT:

1. Review the Material Safety Data Sheet(s) for the material(s) in the drum(s) and take all necessary precautions. Safety shoes,

work gloves, hard hat and other personal protective devices are recommended.

2. Please read all instructions thoroughly before attempting to operate your new MORSE drum handler.

3. The models 185A-M, 185B-M, 185C-M, and 185D-M have a maximum capacity rating of 800 Lb. FULL drum and 500 Lb.

HALF-FULL and are intended for lifting, moving and pouring drums of size and type noted above. DO NOT exceed these

ratings as an unsafe condition may result which could cause damage or excessive wear, or make the unit awkward to

handle.

4. When loading, unloading, operating, or maintaining your MORSE drum handler, always use care and good judgment, have

good footing and a firm hold. Keep hands and loose clothing, etc. away from all moving parts. Never allow anyone to be

below any part of a raised drum handler or drum. Read operating instructions and review the pictures in the sales brochure

before operation.

5. The Model 185M Series is a “Group 1 - Structural and Mechanical” Below-the-Hook Lifting Device which is covered by the

American National Standard ANSI/ASME B30.20. The user should comply with all aspects of this standard.

B. OPERATING INSTRUCTIONS:

1. With Kontrol-Karrier standing on the floor, lower hoist and engage hoist hook into the lifting eye.

2. Raise hoist to lift Kontrol-Karrier clear of floor and move it to the drum.

3. Position Kontrol-Karrier at a height which aligns the saddle band with the center of the drum.

4. With the cinch chain (item 25 or 26) hanging freely, push Kontrol-Karrier against the drum so that saddle will encircle the

drum.

5. Drape the cinch chain (item 25 or 26) across the front of the drum and insert one link into the slot on the ratchet handle (item

36). Turn the ratchet handle clockwise to tighten the cinch chain around the drum (see detail).

6. Raise hoist and position the drum at the pouring station.

7. Pour the drum by pulling on the pull chain (item 4) and rotating the drum to a suitable pouring angle. For best control of drum

pouring angle, pay out one side of the loop while pulling in the other side, thus being able to hold back the drum rotation

after the load shifts.

8. After pouring is completed, rotate the drum back to vertical position and lower hoist to return drum to floor.

9. To remove drum: Pull ratchet handle to relieve pressure on ratchet teeth. Lift pawl handle (item 33) to release teeth engage-

ment and rotate ratchet to loosen chain and allow its removal from notch.

CAUTION: DO NOT allow drum to impact on floor, ground, or dumping station, etc. or there may be damage.

CAUTION: DO NOT exceed weight capacity of 800 Lb. for FULL drum, 500 Lb. for HALF-FULL drum.

C. MAINTENANCE:

1. Lubricate gear teeth and roller chain.

2. Oil ratchet, pawl, saddle hinge and other moving parts periodically.

3. Periodically inspect all moving parts, framework, and contact areas for signs of wear, fatigue, or loosening. Tighten, adjust or

replace parts as necessary to prevent failure and maintain proper function.

MORSE MFG. CO., INC. • 727 West Manlius Street • P.O. Box 518 • East Syracuse, NY 13057-0518

Phone: 315-437-8475 • Fax: 315-437-1029 • Email: [email protected] • Website: www.MORSEmfgco.com

185M SERIES

Kontrol-Karriers with Spark Resistant Parts

The Specialist In Drum Handling Equipment

Parts List for Morse 185M Series

Serial # 0188 - 0407

185M SERIES

Kontrol-Karriers with Spark Resistant Parts

The Specialist In Drum Handling Equipment

Website: www.MORSEmfgco.com

ITEM # SUFFIX,

SEE NOTE 1 QTY. PART # DESCRIPTION

1* 1 1-P CHAIN WHEEL #1-1/2 W/ GUIDE SR

2 1 3-P TRIANGLE & SHAFT W/ BOLTS

3 12 2B-P CHAIN, 1/0 BRASS, PER FT

4* 1 2435-P CHAIN, PULL, BRASS, 1/0, 12'

5 * 2 735-P KEY, WOODRUFF, SIZE 9, ASA606

6 * 1 19-P BEARING, 3/4" ID X 2-1/2"

7 2 55-P WASHER, 3/4 SAE FL 1-1/2 OD

8* 1 11-P SPROCKET, #35 12T, 3/4" BORE

9 1 15-P COLLAR, 3/4" ID

10 * 1 7-P BEARING, 3/4" ID X 1-1/2"

11 1 16-P COLLAR, 1" ID

12 * 1 18-P BEARING, 1" ID X 2-1/2"

13 * 1 12-P CHAIN, ROLLER, #35 W/ M LINK

14 * 1 795-P LINK, MASTER, #35 CHAIN

15 * 1 13-P SPROCKET #35 36T, 3/4" BORE

16 * 1 14-P GEAR, PINION, 7 TOOTH

17 1 29-P SPACER, SPUR GEAR .15"

18 2 22-P SHCS, 3/8-24 X 5/8

19 * 1 23-P GEAR, SPUR, 72T, 1" HOLE

20 1 47M-P OVERHEAD YOKE, 185M SERIES, SR

21 ** A-M 1 725AM-P SADDLE ASM, 285AM, SR

21 ** B-M 1 112BM-P SADDLE ASM, 185B-M, SR

21 ** C-M 1 725CM-P SADDLE ASM, 185CM, SR

21 ** D-M 1 112DM-P SADDLE ASM, 185D-M, SR

22 SADDLE WELDMENT (NOT SOLD SEPARATELY)

23 1 4079-P HHCS, M8 X 60 MM CL8.8, 8MM

24 1 4081-P NUT, M8 ESNA, 8MM

25 A-M, B-M 1 1287-P CHAIN, CINCH, 3/16 SS 33 LK

26 C-M, D-M 1 E14SS FIBRE DRUM STRAP, SS, SR

27 1 64-P ROLL PIN, 3/16 X 1-1/4

29 1 1296-P HHCS, 1/4-20 X 7-1/2 GR5

30 1 1297-P NUT, 1/4-20 REV HEX LOCK

31 1 136-P GRIP, HANDLE 7/8" X 4-3/4"

32 * 1 169-P SPRING, PAWL

33 1 168-P PAWL, WITH DRILLED HOLE

34 1 170-P SCREW, 3/8 DIA X 5/8 SHOULDER

35 1 710-P RETAINER, RATCHET PUSH NUT 3/4

36 1 165-P RATCHET, MALLEABLE, SADDLE

37 1 165KIT-P KIT, RATCHET CHAIN TIGHTENER

38 1 731M-P PLATE, RATCHET HINGE, 1/4", SR (NOT SOLD SEPARATELY)

39* 1 726M-P HINGE PLATE CPT, 1/4" SR

Item 26 has been discontinued and no longer available. Replace with p/n E14sskit-p (KIT, SS STRAP W/ RATCHET)

Note #1:

If no letter is shown, the part is for Models 185A-M, 185B-M, 185C-M and 185D-M. If a letter is shown, the part is for

the model with that letter suffix only.

** Item 21 "SADDLE ASM" (drum holder assembly) includes the "SADDLE WELDMENT" and appropriate attached moving

parts (items 23, 24, 25, 29, 30 and 39).

* Recommended spare parts

Item 25 has been discontinued and no longer available. Replace with p/n 1287kit-p (KIT, 9/32" SS CHAIN W/ RATCHET)

When ordering parts, specify

part number and description,

model number and serial number.

Find model number and serial number

on metal tag attached to Kontrol-Karrier.

185M SERIES

Kontrol-Karriers with Spark Resistant Parts

The Specialist In Drum Handling Equipment

Parts Diagram for Morse 185M Series

Serial # 0188 - 0407

Website: www.MORSEmfgco.com

Dieses Handbuch passt für folgende Modelle

Andere morse Industrieanlagen Handbücher

morse

morse MORStak 289C Bedienungsanleitung

morse

morse 15-SS Bedienungsanleitung

morse

morse 4560BM-P Bedienungsanleitung

morse

morse 310 Series Bedienungsanleitung

morse

morse 82A Series Bedienungsanleitung

morse

morse 285G-HD Bedienungsanleitung

morse

morse PailPro Series Bedienungsanleitung

morse

morse 185A Bedienungsanleitung

morse

morse KK Bedienungsanleitung

morse

morse PailPro Series Bedienungsanleitung

morse

morse M Series Bedienungsanleitung

morse

morse 185HD Series Bedienungsanleitung

morse

morse 285XBP Bedienungsanleitung

morse

morse 1110 Bedienungsanleitung

morse

morse 2-300 Series Bedienungsanleitung

morse

morse 195AM-A Bedienungsanleitung

morse

morse PailPRO 152-5 Bedienungsanleitung

morse

morse 2-15 Bedienungsanleitung

morse

morse 405M-114 Bedienungsanleitung

morse

morse 400A-72-110 Bedienungsanleitung

morse

morse 285AM-HD Bedienungsanleitung

morse

morse 185G-HD Bedienungsanleitung

morse

morse 525-N-124 Bedienungsanleitung

morse

morse 400A-72SS-115 Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung

morse 185M Series Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken