Morse 400A-96-115 Bedienungsanleitung

MORSE Mfg. Co., Inc. •727 West Manlius Street •P.O. Box 518 •East Syracuse, NY 13057-0518

Phone: (315) 437-8475 •Fax: (315) 437-1029 •Email: [email protected] •Website: www.MORSEmfgco.com

The Specialist In Drum Handling Equipment

MODEL 400A-96-115

Hydra-Lift, 96”, DC Power Lift & Tilt

Contents

Page

Receiving Procedures. . . . . . . . . . . . . . . . . 1

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Information. . . . . . . . . . . . . . . . . . . . . 1 - 2

Machine Description. . . . . . . . . . . . . . . . . . . 3 - 4

Operating Instructions. . . . . . . . . . . . . . . . . . . 4 - 5

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . 5

Parts Lists and Diagrams. . . . . . . . . . . . . . . . 6 - 9

Safety Information

While Morse Manufacturing Co. drum handling equipment is

engineered for safety and efficiency, a high degree of

responsibility must be placed upon the machine operator to follow

safe practices, based primarily on common sense, upon which

true safety depends.

Failure to follow the safety precautions in this manual can result

in personal injury or property damage. Observe the same

precautions as with similar machinery where carelessness in

operating or maintenance is hazardous to personnel. Carefully

read the safety precautions below and throughout this manual.

Receiving Procedures

Every Morse drum handler is inspected prior to shipping.

However, damage may be incurred during transit.

• Check for visible damage. If you choose to accept damaged

freight, always sign noting the damage on the BILL OF LADING.

• Document the damage and have the truck driver sign. We

recommend keeping a digital camera at your receiving dock

for this purpose.

• Open packages expeditiously to check the condition of the

goods. There is only a 24 hour window to notify the carrier of

any concealed damage.

• IMMEDIATELY REPORT ALL DAMAGE TO THE SHIPPING

COMPANY! Then you may contact Morse for assistance with

your freight claim.

• Morse Manufacturing will not be held responsible for any

damaged freight that is not signed for as damaged.

Delivery to non-business addresses without a loading dock result

in additional freight charges. Residential delivery fees, inside

delivery fees, re-delivery charges, and lift gate services will be

added by the truck line, and are non-negotiable.

Limited 2 Year Warranty

Morse drum handling equipment is guaranteed against defects

in workmanship or materials for TWO YEARS when used

properly within its rated capacity. Warranty does not cover wear

from normal use or damage from accident or abuse. Motors

and other purchased parts carry the warranties of their

manufacturers.

For warranty claims, contact your Morse Dealer to obtain a

return authorization number, and for return freight advice. Return

freight must be prepaid.

In all instances, liability is limited to the purchase price paid or

to repairing or replacing the product. Customer assumes liability

for any modifications, unauthorized repairs or parts substitution.

Operator’s Manual

for Morse Hydra-Lift Drum Karrier

Model 400A-96-115

Serial Number 0804 to ____ (MMYY)

Safety Information (continued)

DANGER - Indicates a situation which, if not avoided, will result in serious

injury or death. This signal word is limited to the most extreme situations.

WARNING - Indicates a situation which, if not avoided, could result in

serious injury or death.

CAUTION - Indicates a situation which, if not avoided, can result in damage

to the machine.

CAUTION – Do Not Transport with Drum Raised

ALWAYS LOWER THE DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING. The unit

can become unstable when transporting with a raised load.

DANGER - Stay Clear of Power Lines

KEEP WELL CLEAR OF POWER LINES. Never approach a power line. Current in a high voltage line may

arc some distance from the wire to the steel framed, grounded machine.

WARNING

The Hydra-Lift Karrier is designed to handle one drum of the types listed at the top of page 3, under 2.

Machine Description. DO NOT attempt to handle any other type of drum or object. DO NOT exceed the

weight capacity of 800 Lb.

WARNING - Level Floors Only

For operation only on clean, level floors of suitable bearing capacity. Do not use on sloped surfaces, ramps,

irregular or debris strewn floors.

WARNING - Do Not Modify the Unit

Under no circumstances should any modifications be made to the Morse machinery without factory authorization.

Any modifications may void the warranty. This machine was designed to perform a specific job and alterations

may result in injury to operator or machine.

WARNING - No Loose Fitting Clothing

Wear close-fitting clothing and safety equipment appropriate to the job. Loose fitting clothing may become

caught on the machinery and cause severe personal injury.

WARNING - Hydraulic Fluid Under Pressure Can Be Hazardous

Escaping hydraulic fluid under pressure can penetrate the skin, causing serious injury. Avoid the hazard by

relieving pressure before disconnecting hydraulic lines. Keep hands and body away from pinholes and

nozzles, which eject fluid under high pressure. Use a piece of cardboard to search for leaks. If an accident

occurs, see a doctor immediately and inform them of the nature of the accident.

CAUTION - Wear Safety Shoes

Wear safety shoes with non-slip soles and hard toe protection.

Operator’s Manual for Morse Hydra-Lift Drum Karrier Model 400A-96-115

Serial Number 0804 to ____ (MMYY)

The Specialist In Drum Handling Equipment

MODEL 400A-96-115

Hydra-Lift, 96”, DC Power Lift & Tilt

Machine Description

The Model 400A-96-115 Hydra-Lift Karrier will pour a drum up to 96” high, measured from the floor to the lowest point of a

horizontal drum. It is designed to lift, transport, and dispense a ribbed 55-gallon steel drum 22.5” in diameter.

• Asmaller diameter drum can be handled with the correct size 55/30 Series Diameter Adaptor installed

(see Diameter Adaptor literature)

• A55-gallon plastic drum can be handled if the unit is equipped with an Adjustable Bracket (Option HDPS) or Top Rim Clamp

(Option HDRC)

(see plastic drum option manual).

The maximum full-drum capacity is 800 Lb. The capacity is derated to 500 Lb. for a half-full drum. The half-full rating is based on

the tilt mechanism’s capacity for handling an unbalanced bottom-

heavy drum.

Controls

The Morse Hydra-Lift Karrier is manually propelled and steered.

The drum lift and tilt controls are powered by a 12V DC motor

with a momentary switch.

There are two functions for the operator to control (Figure 2.1):

1. “LIFT” and lower function for vertical positioning of the drum

2. “TILT” function to control the degree of rotation of the drum

1. LIFT and Lower Function

To raise the drum

a. Turn the motor on by holding the momentary switch

in the on position.

b. With the motor on, raise the LIFT handle.

To lower the drum

a. With the motor off, push in the LOWER handle.

2. TILT Function

To tilt the drum forward for pouring

a. Turn on the motor by holding momentary switch in

the on position.

b. With the motor on, raise the tilt handle.

To return the drum to vertical position

a. Turn on the motor by holding momentary switch in

the on position.

b. Push the tilt handle down.

Operator’s Manual for Morse Hydra-Lift Drum Karrier Model 400A-96-115

Serial Number 0804 to ____ (MMYY)

The Specialist In Drum Handling Equipment

MODEL 400A-96-115

Hydra-Lift, 96”, DC Power Lift & Tilt

Figure 2.1

WARNING - Watch Out for Pinch Points

Stay clear of moving parts. Operator should remain behind the push handle during the lift operation.

Figure 3.2

Floor Lock

The screw-down floor lock is located on the base of the tower

(figure 3.1). Turning the floor lock clockwise until it locks in the

down position activates the floor lock. When the floor lock is

activated it prevents unwanted free wheeling of the unit. Floor

conditions determine the effectiveness of the floor lock. The

operator should verify its holding action before depending on it

to hold.

Drum Holder Assembly

The drum holder assembly (or “saddle assembly”) is the

component on the Hydra-Lift Karrier that is intended to hold the

drum. The drum holder assembly is designed to secure a

standard ribbed 55-gallon steel drum around it’s middle using a

cinch chain and ratchet tightening system. The drum holder

accepts accessories for handling smaller diameter drums.

Operating Instructions

1.) Push the Hydra-Lift Karrier to the drum.

2.) Using the “LIFT” control as described in “Machine

Description - Controls” (page 3) , position the drum holder

assembly with the back band at the middle of the drum.

(Figure 3.1). With the ratchet plate swung open and the

cinch chain hanging from the chain hook, push the unit until

the back band rests firmly against the drum. Some

adjustment to the tilt angle of the saddle may be necessary

to ensure band fits flush on the drum.

3.) Attaching the drum:

Drape the chain across the front of the drum and engage a

link into the slot in the ratchet (Figure 3.2). Turn the ratchet

clockwise to tighten chain. If ratchet turns until the pawl is

beyond the last ratchet tooth, turn the ratchet back and slide

the next link into the ratchet slot and try tightening again.

The chain must be held tightly against the drum with the pawl

engaged securely in the ratchet teeth.

4.) Operate the lift function to lift drum clear of floor. Roll to

dispensing location. NOTE: Do not allow the drum to impact

on floor, pouring station, etc. or a spill or damage could

occur.

Figure 3.1

Operator’s Manual for Morse Hydra-Lift Drum Karrier Model 400A-96-115

Serial Number 0804 to ____ (MMYY)

The Specialist In Drum Handling Equipment

MODEL 400A-96-115

Hydra-Lift, 96”, DC Power Lift & Tilt

CAUTION – Do Not Transport with Drum Raised

ALWAYS LOWER THE DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING. The unit

can become unstable when transporting with a raised load.

5.) Lift drum to desired pouring height. Operate the tilt control as described in “Machine Description - Controls” (page 3) to

adjust the drum attitude. This is especially important when lifting an open drum. The floor lock should be engaged while

dispensing / draining.

6.) When dispensing is complete, tilt drum back to upright position. Disengage the floor lock and lower the drum to transporting

height; about 6” off the floor.

WARNING - Stay Clear of Raised Drum

NEVER allow anyone to be below any part of a raised drum handler or drum. Remain behind the push handle

while handling a drum.

WARNING – Do NOT Disengage the Cinch Chain When Drum is off the Ground

When the drum is in the upright position, lower the drum to the floor before releasing the cinch chain.

7.) Push the unit to the drum storage area and lower to the floor in an upright position. Release the cinch chain from the ratchet

by applying pressure to the ratchet handle in a clockwise direction with one hand and opening the pawl to free the ratchet

with the other hand. Remove the cinch chain link from the ratchet.

Maintenance

Periodic inspection for the general condition of structural and mechanical components is imperative for safe and efficient operation.

Periodically inspect all moving parts, framework, and contact areas for signs of wear, fatigue, or loosening. Tighten, adjust, or

replace parts as necessary to prevent failure and maintain proper function.

Inspect the hydraulic system for oil drips, hose damage, or other signs of wear. Inspect the level and condition of the hydraulic

fluid. Replace any parts that show signs of wear.

Grease wheel bearings periodically. Oil or grease all moving parts including: the three clevis pins and the surfaces of the boom

which contact the inside of the mast cap, the hinge pin, the gears and sprockets in the tilt drive, and the ratchet and pawl.

Worn or damaged parts must be properly replaced with the correct, genuine Morse parts.

Hydraulic pump is shipped filled with Noco Premium plus automatic transmission fluid d/m. Material safety data sheet (msds) is

available online. Change oil yearly, sooner depending on dirty conditions or outdoor use. Replace oil with Mobil dte 24 or

equivalent for indoor use (Mobil dte 13 for outdoor use).

Operator’s Manual for Morse Hydra-Lift Drum Karrier Model 400A-96-115

Serial Number 0804 to ____ (MMYY)

The Specialist In Drum Handling Equipment

MODEL 400A-96-115

Hydra-Lift, 96”, DC Power Lift & Tilt

Parts List for Morse Hydra-Lift Drum Karrier Model 400A-96-115

Serial Number 0804 to ____ (MMYY)

The Specialist In Drum Handling Equipment

MODEL 400A-96-115

Hydra-Lift, 96”, DC Power Lift & Tilt

ITEM # QTY. PART # DESCRIPTION

1 1 3998-P OVERHEAD ASM, 96" PT

2 4 1521-P HHCS, 3/8-16 X 3 GR5

3 4 1166-P WASHER, 3/8 USS 1" OD

4 2 134-84-P LEG WELD, 400A-84, 96, 405

5 2 704-P AXLE, 3/4", USE WITH PUSH-ON

6 2 705-P CAP, HUB, PUSH-ON, 3/4"

7 * 2 87-P WHEEL, MORTUF, 8", 3/4" BRG

8 3 64-P ROLL PIN, 3/16 X 1-1/4

9 7 17-P WASHER, 5/8 SAE FL 1-5/16 OD

10 * 2 3308-P CASTER, 4" SWIVEL, DBL RACE

11 8 491-P NUT, LOCK, 5/16-18 REV HEX

12 3 138-P CLEVIS PIN 5/8 X 3"

13 4 1169-P NUT, LOCK, 3/8-16 REV HEX

14 8 215-P HHCS, 5/16-18 X 5/8 GR2

15 2 765-P HYD FIT, MALE ELBOW, FLARE 400

16 1 3006-P CYLINDER, 1.5 X 29 510 515 611

17 2 136-P GRIP, HANDLE 7/8" X 4-3/4"

18 1 3999DC-P TOWER WELD, DC, 400A-96

19 1 3680-P KIT, PUMP MOUNT PLATE, PL

20 1 155-P HHCS, 3/8-16 X 2-1/2 GR2

21 1 3641-P U-BOLT, 3/8-16, 400 PUMP MOUNT

22 1 3643-P MOUNT PLATE, POWER PUMP

23 7 1474-P WASHER, 3/8 SPLIT LOCK

24 2 149-P NUT, FIN, 3/8-16 HEX

25 1 1657-P HHCS, 3/8-16 X 3/4 GR2

26 1 1165-P NUT, JAM, 3/8-16

27 1 3690-P HYD HOSE ASM, 22"

28 1 345-P HYD FIT, MALE FLARE, 456, 82

29 1 3177-P VALVE, P.C. FLOW CONT .75 GPM

30 1 1108-P HYD FIT, PIPE NIPPLE, 1/4"

31 1 404-P CABLE HARNESS 20", 20" -125

32 1 M3500-P HYD POWER PACK, -115

33 1 193-P SCREW, TEK, 12-14 X 3/4, 3 PT

34 1 4168-P WASHER, 7/32, 1-1/2 OD, FENDER

35 1 1729-P BOTTOM, BATTERY BOX, 400

36 1 388-P BATTERY, 12V DC

37 1 403-P BATTERY CABLE HARNESS 20", 30"

38 1 1728-P TOP, BATTERY BOX, 400, 285A-BP

39 1 389-P CHARGER, BATTERY, 110V TO 12V

40 2 1765-P HYD HOSE ASM, 96 PT, 101"

* Recommended spare parts.

Parts Diagram for Morse Hydra-Lift Drum Karrier Model 400A-96-115

Serial Number 0804 to ____ (MMYY)

The Specialist In Drum Handling Equipment

MODEL 400A-96-115

Hydra-Lift, 96”, DC Power Lift & Tilt

Overhead Assembly (Part Number 3998-P)

for Morse Hydra-Lift Drum Karrier Model 400A-96-115

Serial Number 0804 to ____ (MMYY)

The Specialist In Drum Handling Equipment

MODEL 400A-96-115

Hydra-Lift, 96”, DC Power Lift & Tilt

ITEM # QTY. PART # DESCRIPTION

50 1 745A-P SADDLE ASM, A-HD, '88

51 1 726-P * A RATCHET HINGE PLATE CPT 1/4"

52 1 1296-P * HHCS, 1/4-20 X 7-1/2 GR5

53 1 1297-P * NUT, LOCK, 1/4-20 REV HEX

54 1 180-P * CHAIN, CINCH, 3/16 ALLOY 33 LK

55 1 4081-P * NUT, ESNA, M8, 8MM

56 1 4079-P * HHCS, M8 X 60 MM GR5, 8MM

57 1 27-P * SPUR GEAR W/ 1" SHAFT, HD TYPE

59 1 29-P SPACER, SPUR GEAR .15"

60 1 731-P A RATCHET HINGE PLATE ONLY 1/4 (NOT SOLD SEPARATELY)

61 1 165KIT-P KIT, RATCHET CHAIN TIGHTENER

62 1 168-P PAWL, WITH DRILLED HOLE

63 1 169-P PAWL SPRING

64 1 170-P SCREW, SHOULDER, 3/8 DIA X 5/8

65 1 710-P RETAINER, RATCHET PUSH NUT 3/4

66 1 165-P RATCHET, MALLEABLE, FOR SADDLE

67 1 136-P GRIP, HANDLE 7/8" X 4-3/4"

68 1 3997-P OVERHEAD WELD, 96" PT

69 1 64-P ROLL PIN, 3/16 X 1-1/4

70 2 55-P WASHER, 3/4 SAE FL 1-1/2 OD

71 1 735-P * KEY, WOODRUFF, SIZE 9, ASA606

72 1 14-P * GEAR, PINION, 7 TOOTH

73 1 12-P * CHAIN, ROLLER, #35 W/ M LINK

74 1 795-P LINK, MASTER, #35 CHAIN

75 1 13-P * SPROCKET #35 36T, 3/4" BORE

76 1 1116-P * SPROCKET #35 17T, 1" BORE

77 4 1657-P HHCS, 3/8-16 X 3/4 GR2

78 4 1474-P WASHER, 3/8 SPLIT LOCK

79 1 2656-P * KEY, SQUARE, 1/4 X 1"

80 2 2120-P HYD FIT, MALE CONNECTOR, 400

81 1 351-P MOTOR, HYDRAULIC HYD, 400, 456

82 1 7-P * BEARING, 3/4" ID X 1-1/2"

83 2 18-P * BEARING, 1" ID X 2-1/2"

84 2 736-P * KEY, WOODRUFF, SIZE 15, ASA808

85 1 15-P COLLAR, 3/4" ID

86 1 30-P * SPROCKET #40D 16T, 1" BORE

87 1 31-P * CHAIN, ROLLER, #40D W/ M. LINK

88 1 796-P LINK, MASTER, #40D CHAIN

89 1 32-P * SPROCKET #40D 32T, 1" BORE

90 1 1049-P KIT, SQ COVER, 400 PT

91 1 1772-P COVER HALF SQ, 1 HOLE, 400 PT

92 1 1755-P COVER HALF SQ, NO HOLES 400 PT

93 9 193-P * SCREW, TEK, 12-14 X 3/4, 3 PT

* Recommended spare parts.

Overhead Assembly (Part Number 3998-P)

for Morse Hydra-Lift Drum Karrier Model 400A-96-115

Serial Number 0804 to ____ (MMYY)

The Specialist In Drum Handling Equipment

MODEL 400A-96-115

Hydra-Lift, 96”, DC Power Lift & Tilt

Andere Handbücher für 400A-96-115

Inhaltsverzeichnis

Andere morse Hebesystem Handbücher

morse

morse 510M-114 Bedienungsanleitung

morse

morse 515-N-120 Bedienungsanleitung

morse

morse Hydra-Lift 400A-60 Bedienungsanleitung

morse

morse 82A-120 Bedienungsanleitung

morse

morse 185AM Bedienungsanleitung

morse

morse 400A-96SS Bedienungsanleitung

morse

morse 510M Bedienungsanleitung

morse

morse 80APS Bedienungsanleitung

morse

morse 400A-60-120 Bedienungsanleitung

morse

morse 400A-72-127 Bedienungsanleitung

morse

morse 400A-96-114 Bedienungsanleitung

morse

morse 525M-T Bedienungsanleitung

morse

morse 81 Bedienungsanleitung

morse

morse 400A-96-127 Bedienungsanleitung

morse

morse 8A-GT-125 Bedienungsanleitung

morse

morse 85AM Bedienungsanleitung

morse

morse 400A-60-110 Bedienungsanleitung

morse

morse 195A Series Bedienungsanleitung

morse

morse 86 Bedienungsanleitung

morse

morse 400AM-60 Bedienungsanleitung

morse

morse 42 Series Bedienungsanleitung

morse

morse 86 Bedienungsanleitung

morse

morse 400A-96SS-114 Bedienungsanleitung

morse

morse 195A-A Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung

Ricon

Ricon Mirage F9T Bedienungsanleitung

morse 400A-96-115 Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken