Motion Control Engineering 2000 Bedienungsanleitung

Motion Control Engineering, Inc.

11380 White Rock Road

Rancho Cordova, CA 95742

voice 916 463 9200

fax 916 463 9201

www.mceinc.com

Manual # 42-02-1P21, Rev A9 October 2016

Motion 2000 Hydraulic Controller

V9.xx software

This document may not be reproduced, electronically or mechanically, in whole or in part, without

written permission from Motion Control Engineering.

Trademarks

All trademarks or registered product names appearing in this document are the exclusive property

of the respective owners.

Warning and Disclaimer

Although every effort has been made to make this document as complete and accurate as possible,

Motion Control Engineering and the document authors, publishers, distributors, and

representatives have neither liability nor responsibility for any loss or damage arising from

information contained in this document or from informational errors or omissions. Information

contained in this document shall not be deemed to constitute a commitment to provide service,

equipment, or software by Motion Control Engineering or the document authors, publishers,

distributors, or representatives.

Limited Warranty

Motion Control Engineering (manufacturer) warrants its products for a period of 15 months from

the date of shipment from its factory to be free from defects in workmanship and materials. Any

defect appearing more than 15 months from the date of shipment from the factory shall be

deemed to be due to ordinary wear and tear. Manufacturer, however, assumes no risk or liability for

results of the use of the products purchased from it, including, but without limiting the generality

of the forgoing: (1) The use in combination with any electrical or electronic components, circuits,

systems, assemblies or any other material or equipment (2) Unsuitability of this product for use in

any circuit, assembly or environment. Purchasers’ rights under this warranty shall consist solely of

requiring the manufacturer to repair, or in manufacturer's sole discretion, replace free of charge,

F.O.B. factory, any defective items received at said factory within the said 15 months and

determined by manufacturer to be defective. The giving of or failure to give any advice or

recommendation by manufacturer shall not constitute any warranty by or impose any liability upon

the manufacturer. This warranty constitutes the sole and exclusive remedy of the purchaser and

the exclusive liability of the manufacturer, AND IN LIEU OF ANY AND ALL OTHER WARRANTIES,

EXPRESSED, IMPLIED, OR STATUTORY AS TO MERCHANTABILITY, FITNESS, FOR PURPOSE SOLD,

DESCRIPTION, QUALITY PRODUCTIVENESS OR ANY OTHER MATTER. In no event will the

manufacturer be liable for special or consequential damages or for delay in performance of this

warranty.

Products that are not manufactured by MCE (such as drives, CRTs, modems, printers, etc.) are not

covered under the above warranty terms. MCE, however, extends the same warranty terms that

the original manufacturer of such equipment provide with their product (refer to the warranty

terms for such products in their respective manual).

End User License Agreement

This End User License Agreement (“Agreement”) grants you the right to use the software con-

tained in this product (the “Software”) subject to the following restrictions: You may not: (i) copy

the Software, except for archive purposes consistent with your standard archive procedures; (ii)

transfer the Software to a third party apart from the entire product; (iii) modify, decompile, disas-

semble, reverse engineer or otherwise attempt to derive the source code of the Software; (iv)

export the Software or underlying technology in contravention of applicable U.S. and foreign

export laws and regulations; and (v) use the Software other than in connection with operation of

the product.

“LICENSOR'S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY,

ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH

SUPPLIERS, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGE-

MENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.”

Important Precautions and Useful Information

This preface contains information that will help you understand and safely maintain MCE

equipment. We strongly recommend you review this preface and read this manual before

installing, adjusting, or maintaining Motion Control Engineering equipment. This preface dis-

cusses:

• Safety and Other Symbol Meanings

• Safety Precautions

• Environmental Considerations

• In this Manual

Safety and Other Symbol Meanings

Danger

This manual symbol is used to alert you to procedures, instructions, or situations which, if

not done properly, might result in personal injury or substantial equipment damage.

Caution

This manual symbol is used to alert you to procedures, instructions, or situations which, if

not done properly, might result in equipment damage.

Note

This manual symbol is used to alert you to instructions or other immediately helpful informa-

tion.

Safety Precautions

Danger

This equipment is designed to comply with ASME A17.1, National Electrical Code, CE, and

CAN/CSA-B44.1/ASME-A17.5 and must be installed by a qualified contractor. It is the

responsibility of the contractor to make sure that the final installation complies with all

local codes and is installed in a safe manner.

This equipment is suitable for use on a circuit capable of delivering not more than 10,000

rms symmetrical amperes, 600 volts maximum. The three-phase AC power supply to the

Drive Isolation Transformer used with this equipment must originate from a fused discon-

nect switch or circuit breaker sized in conformance to all applicable national, state, and local

electrical codes in order to provide the necessary motor branch circuit protection for the

Drive Unit and motor. Incorrect motor branch circuit protection will void the warranty and

may create a hazardous condition.

Proper grounding is vitally important to safe and successful operation. Bring your ground

wire to the system subplate. You must choose the proper conductor size and minimize the

resistance to ground by using the shortest possible routing. See National Electrical Code

Article 250-95 or the applicable local electrical code.

Before applying power to the controller, physically check all the power resistors and other

components located in the resistor cabinet and inside the controller. Components loosened

during shipment may cause damage.

For proper operation of your controller, you must make sure that: 1) A direct solid ground is

provided in the machine room to properly ground the controller and motor. Indirect

grounds such as the building structure or a water pipe may not provide proper grounding

and could act as an antenna to radiate RFI noise, thus disturbing sensitive equipment in the

building. Improper grounding may also render any RFI filter ineffective. 2) The incoming

power to the controller and the outgoing power wires to the motor are in their respective,

separate, grounded conduits.

This equipment may contain voltages as high as 1000 volts. Use extreme caution. Do not

touch any components, resistors, circuit boards, power devices, or electrical connections

without ensuring that high voltage is not present.

Environmental Considerations

• Keep the machine room clean.

•Controllersaregenerally in NEMA 1 enclosures.

• Do not install the controller in a dusty area.

• Do not install the controller in a carpeted area.

• Keep room temperature between 32 and 104 degrees F (0 to 40 degrees C).

• Prevent condensation on the equipment.

• Do not install the controller in a hazardous location or where excessive amounts of

vapors or chemical fumes may be present.

• Make certain that power line fluctuations are within plus or minus 10% of proper value.

Air Conditioned Equipment Cabinets

If your control or group enclosure is equipped with an air conditioning unit, it is very important

to observe the following precautions. (Failure to do so can result in moisture damage to electri-

cal components.)

• Maintain the integrity of the cabinet by using sealed knockouts and sealing any holes

made during installation.

• Do not run the air conditioning while the cabinet doors are open.

• If you turn the air conditioner off while it is running, wait at least five minutes before

restarting it. Otherwise, the compressor may be damaged.

• Observe the recommended thermostat setting (75 degrees) and follow recommended

maintenance schedules.

• Make certain that the air conditioning drain tube remains clear to avoid water accumula-

tion in the unit.

In This Manual:

This manual is the installation, adjustment, and troubleshooting guide for the HMC-2000 car

control. When viewed online as a pdf file, hyperlinks (buttons or blue text) link to related topics

and informational websites. The manual includes:

•Contents: Table of Contents. When viewed online as a pdf file, hyperlinks in the Contents

link to the associated topic in the body of the manual.

•Section 1. Motion 2000 Description: A description of the Motion 2000 controller and

circuit boards.

•Section 2. Installation: Installation and wiring guidelines.

•Section 3. Startup - Inspection Operation: Controller startup, operation on Inspection,

installation of hoistway equipment and preparing the car to run on Test/Normal opera-

tion.

•Section 4. Final Adjustment: A description of absolute floor encoding and Test mode

operation. Running the car on Test and Normal operation and making the final checks

and adjustments prior to releasing the car to normal operation.

•Section 5. The Computer: How to use the MPU to program and troubleshoot the control-

ler. Complete with parameter definitions where appropriate.

•Section 6. Troubleshooting: This section includes Status and Error Messages, PC Board

Quick References and Data Trap instructions.

•Section 7. Appendix: Record of Parameter Values, Security Codes, LS-QUTE Landing

System.

•Index: Alphabetical index to help you find information in the manual. When viewed

online as a pdf file, index entry page references are hyperlinks to the associated informa-

tion in the body of the manual.

Contents

Important Precautions and Useful Information

Safety and Other Symbol Meanings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-iv

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-iv

Environmental Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-v

Air Conditioned Equipment Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-v

In This Manual: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-vi

Section 1. Motion 2000 TSSA Description

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Car Controller Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Controller Circuit Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

Landing System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-9

LS-QUTE Landing System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

LS-STAN Landing System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10

LS-EDGE Landing System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Operating Mode Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Automatic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12

Mode Entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Inspection Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13

Cartop Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

In Car Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Machine Room Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14

Hoistway Access Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14

Attendant Service Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-15

Mode Entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15

Independent Service Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-15

Mode Entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15

Sabbath Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-16

Emergency Medical Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-16

Hospital Service Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-17

Fire Service Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-17

ii Manual # 42-02-1P21

Emergency Power Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-18

Generator Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18

EPS Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18

Car Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-18

Capture for Test (Pretest) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-19

Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-19

Monitoring and Control Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-20

iMonitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20

iReport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20

BMS-Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-21

Motion Portable Adjustment Control (mPAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-21

mView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22

Section 2. Installation

In this Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Personal Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Equipment Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Machine Room Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Piping and Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

How Electrical Noise Occurs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

How to Avoid Electrical Noise Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Possible EMI/RFI Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Recommended Tools and Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Wiring Prints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Drawing Number Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Nomenclature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Controller Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7

Controller Wiring Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

General Wiring Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

Proper Grounding Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Wiring Connections for Properly Grounded Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Ground Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Main AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Pump Motor Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Low Voltage Signal Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Traveling Cable Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Section 3. Startup - Inspection Operation

In this Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Check for Shorts to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

Before Applying Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

iii

Applying Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3

Initial Adjustments and Power Phasing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Set Up for Construction Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

Required Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Temporary Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Resolving Faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Temporary Run Box Hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Verifying Proper Starter Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7

Hoistway Control Equipment Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9

Installing the LS-QUTE Landing System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Installing the LS-QUTE Landing System Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Installing the Magnetic Strips on LS-QUTE Steel Tape . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Installing the LS-QUTE Hoistway Limit Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

LS-EDGE Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11

LS-EDGE Tape Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

LS-EDGE Top Hanger Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

LS-EDGE Bottom Hanger Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

LS-EDGE Broken Tape Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

Hanging the Tape. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

LS-EDGE Sensor Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

LS-EDGE Door Zone Magnets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

LS-EDGE Terminal Magnets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

LS-EDGE Terminal Magnet Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

LS-EDGE Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

Parameter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

Hoistway Learn Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

Adjusting Floor Heights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

Initial Stepping Distances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

Door Position Monitor Switch (If used) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

LS-EDGE Short Floors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21

Door Zone Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21

Permanently Attach Magnets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21

Complete the Installation and Field Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-22

Preparing the Car to Run on Test/Normal Mode . . . . . . . . . . . . . . . . . . . . . . . 3-22

Section 4. Final Adjustment

In this Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Diagnostic Messages and Input/Output Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Onboard Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Absolute Floor Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Registering Car Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

Test Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Running on Test/Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

iv Manual # 42-02-1P21

Final Adjustments on Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6

Hydraulic Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Slowdown and Limit Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Motor Limit Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Valve Limit Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Relevel Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Final Adjustments on Independent Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7

Door Operator Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Door Open/Close Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Final Adjustments on Normal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Hall Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Ride and Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Recheck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Random Call Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Remote Governor Testing (Roped Hydro) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Static Testing:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Dynamic Testing:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Final Testing, LS-EDGE Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10

Bottom Terminal Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Top Terminal Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Restore Original Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Release to Normal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Section 5. The Computer

In this Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

The HC-MPU Main Processor Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2

Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Switches, Buttons & Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Status Displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Computer Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5

Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Diagnostic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

Getting into Diagnostic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Function of N Push Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Function of S Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Function of + Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Function of - Push Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Format of LCD Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Troubleshooting Using the Computer's Internal Memory . . . . . . . . . . . . . . . . . . . . . . . 5-9

Troubleshooting Specific Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12

Setting Parameters (Options) to Default Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13

Inhaltsverzeichnis

Andere Motion Control Engineering Controller Handbücher

Motion Control Engineering

Motion Control Engineering Motion 4000 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung