motogadget mo.rear Bedienungsanleitung
Instruction manual
mo.rear
EN V1.0
rear light module
Thank you for choosing a quality product from motogadget. All motogadget products are
developed and manufactured in Germany.
Please read the following information and recommendations thoroughly and follow these in-
structions during installations and use of the product. No liability shall be assumde by motoga-
dget for damage or defects resulting from negligence or failure to follow the operating and
installation guide.
motogadget GmbH
Wollenberger Str. 4i/j
13053 Berlin, Germany
Tel. +49 (0)30-6900410-0
motogadget.com
Copyright © 2023 motogadget GmbH, Berlin.
motogadget is a registrated trademark
of the motogadget GmbH, Berlin, Germany.
1. Review of Delivery
All products from motogadget are thoroughly checked to ensure they are completely fault-free
when dispatched. Please check the received goods immediately for possible transport dama-
ge. If you find any damage or other deficiencies, please contact us immediately.
In this regard, we refer to our General Terms of Business and Delivery, which are published
at www.motogadget.com. Should a return of the received delivery be agreed, please note that
we only take back goods in their original packaging. The mo.switch and its accessories must be
returned within the legal period of time and without any traces of use. We shall not assume any
liability for returns which are insufficiently insured or packed.
2. Exclusion of Liability
THE DEVICE AND ITS ACCESSORIES MUST BE INSTALLED BY A CERTIFIED MO-
TORCYCLE TECHNICAN AND IN AN AUTHORIZED SERVICE CENTER. MOTOGADGET
ACCEPTS NO LIABILITY FOR DIRECT OR INDIRECT DAMAGE OR SUBSEQUENT DA-
MAGE OF ANY KIND RESULTING FROM THE USE, INSTALLATION OR CONNECTION
OF THE DEVICE OR OTHER DELIVERED EQUIPMENT. THIS EXCLUSION OF LIABILITY
PARTICULARLY INCLUDES DAMAGE TO PERSONS, MATERIAL LOSSES AND FINAN-
CIAL DAMAGES. THE USE IN AREAS OF PUBLIC TRAFFIC ENSUES AT THE USER’S
OWN RISK. THE USE OF THE DELIVERED DEVICE AND ITS ACCESSORIES FOR RA-
CING OR OTHER COMPETITIONS AS WELL AS FOR ANY USE NOT CORRESPONDING
TO THE RECOMMENDED APPLICATION ALL WARRANTY CLAIMS SHALL BE INVALID.
3. Safety instructions
• BEFORE ANY WORK ON THE VEHICLE’S ELECTRICAL SYSTEM, THE
BATTERY MUST TO BE COMPLETELY DISCONNECTED. TO DO SO, AT
FIRST THE MINUS POLE AND THEN THE PLUS POLE IS DISCONNECTED.
WHEN RECONNECTING, DO IN REVERSE ORDER.
• IT IS NOT POSSIBLE TO USE THE MO.REAR AT VEHICLES WITH POSTIVE
BATTERY POLE FOR VEHICLE GROUND.
• IT IS NOT POSSIBLE TO USE THE MO.REAR ON VEHICLES WITH A 6V
ELECTRICAL SYSTEM.
• IT IS NOT POSSIBLE TO USE THE MO.REAR ON VEHICLES WITHOUT
BATTERY.
• THE MO.REAR MUST BE INSTALLED AND CONNECTED QUALIFIED
PROFESSIONALS.
• ALL CABLE CROSS SECTIONS MUST MATCH THE CURRENT FLOW.
• ALL ELECTRICAL CONNECTIONS IN THE CABLE HARNESS AND ON THE
TERMINALS MUST BE PROFESSIONAL AND FLAWLESS.
4. Features
mo.rear is an all-in-one vehicle tail light unit for motorcycles for use within the EU.
When attached to the vehicle in a compliant manner, the light unit complies with the applica-
ble EU directives and regulations. There is no obligation to register and no documents need
to be carried.
5. Technical Data
• Weight: 150g
• Dimensions: 13.5mm high x 12.5mm deep x 200mm long
• Functions: taillight, brake light, left turn signal, right turn signal, license
plate light, reflector
• Protection class: IP69
• Power consumption: 12V - 2W / 2W / 3W
• Mounting thread: M4 or M5
• Hole spacing: 150mm
6. Installation according to Category 1 approval (license plate size 240x130mm)
The mo.rear is attached to the rear of the vehicle centrally above the license plate using 2
pieces M4 or M5 screws according to the following sketch:
AB
D
EF
C
7. Electrical Connection
The individual wires are connected as follows:
• black: vehicle ground
• red: brake light
• yellow: taillight & license plate light
• green: left turn signal
• white: right turn signal
8. Important Instructions
• The light module must be installed in center and above the license plate, as shown in the
installation sketch.
• The license plate must be illuminated evenly and completely.
• The light module is compatible with 12V DC electrical systems with a battery only.
• The connection cable must be routed without kinks or tension and must not be mechanically
damaged.
• After assembly, the correct function of the ABS and CAN-BUS warning lights must be che-
cked.
• In modern vehicles an error message may occur due to the lower power consumption of the
light unit. In this case, resistors connected in parallel to the respective lamp function can help.
• Before each journey, check that the light unit is functioning correctly.
We wish you a safe ride and look forward to
your positive review.
If you are not satisfied, please give us the opportunity to correct it
Inhaltsverzeichnis
Andere motogadget Steuereinheit Handbücher
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
