Motorola 68HC12B32 Bedienungsanleitung

2000 2813 Industrial Ln. •Garland, TX 75041 •(972) 926-9303 FAX (972) 926-6063

email: [email protected] •web: http://www.axman.com

xiom

anufacturing

CME-12B/BC

Development Board for Motorola

68HC12B32 and 68HC12BC32 Microcontrollers

CONTENTSCONTENTS

GETTING STARTED............................................................................................3

Installing the Software.....................................................................3

Board Startup..................................................................................3

Support Software ............................................................................4

Software Development....................................................................4

TUTORIAL............................................................................................................5

Creating source code......................................................................5

Assembling source code.................................................................6

Running your application ................................................................7

Programming Flash EEPROM.........................................................8

MEMORY MAP.....................................................................................................9

CONFIG SWITCH...............................................................................................10

MEM-SEL JUMPERS .........................................................................................10

PORTS AND CONNECTORS ............................................................................11

LCD_PORT...................................................................................11

KEYPAD........................................................................................11

MCU_PORT..................................................................................12

CAN_PORT...................................................................................12

COM1 SERIAL PORT...................................................................13

J2 ..................................................................................................13

BUS_PORT...................................................................................13

BDM-IN .........................................................................................14

EVU Compatibility Jumpers...........................................................14

TROUBLESHOOTING .......................................................................................15

Code Execution ...................................................................... 16

TABLES..............................................................................................................17

TABLE 1. LCD Command Codes.................................................17

TABLE 2. LCD Character Codes..................................................17

TABLE 3. D-Bug12 Monitor Commands.......................................18

GETTING STARTED

The Axiom CME-12B/BC single board computer is a fully assembled, fully functional

development system for the Motorola 68HC12B32 and BC32 microcontrollers, complete with

wall plug power supply and serial cable. Support software for this development board is

provided for Windows 95 and NT operating systems and DOS.

Follow the steps in this section to get started quickly and verify everything is working correctly.

Installing the Software

1. Insert the Axiom 68HC12 support disk in your PC. If the setup program does not start, run

the file called "SETUP.EXE" on the disk.

2. Follow the instructions on screen to install the support software onto your PC.

3. The flash programming utilities require you to specify the board you are using. You

should select either “CME-12B32” or "CME-12B/BC" for this board.

Board Startup

Follow these steps to connect and power on the board. This assumes you're using the

provided AXIDE or AX12 terminal program (installed in the previous section) or a similar

communications terminal program on your PC. If you're using a different terminal program

than the one provided, set it's parameters to 9600 baud, N,8,1.

1. Make certain the CONFIG SWITCH is set as follows:

1234 567 8

ON ON ON ON OFF ON OFF OFF

2. Connect one end of the supplied 9-pin serial cable to a free COM port on your PC.

Connect the other end of the cable to the COM1 port on the CME-12B/BC board.

3. Apply power to the board by plugging in the power adapter that came with the system.

4. If everything is working properly, you should see a message to “PRESS KEY TO START

MONITOR…” in your terminal window. Press the ENTER key and you should see:

D-Bug12 v2.0.2

For Commands type "Help"

> _

5. Your board is now ready to use! If you do not see this message prompt, or if the text is

garbage, see the TROUBLESHOOTING section at the end of this manual.

Support Software

There are many useful programs and documents on the included HC12 support disk that can

make developing projects on the CME-12B/BC easier. You should browse the disk and copy

anything you want to your hard drive. See the README.TXT file for a description of what is

included.

The flash programming utilities communicate with the board via its COM1 port and the

supplied cable. These programs also include a simple Terminal for interfacing with other

programs running on the CME-12B/BC, such as the D-Bug12 and information from your own

programs that send output to the serial port.

Also on the disk is a free assembler, example source code, and other tools to get you started.

Software Development

Software development on the CME12B32 can be performed using either the DBUG12 monitor

utility installed in EPROM (sockets U6/U7), the DBUG12 monitor programmed into the internal

Flash EPROM or a Background Debug Module (BDM) connected to the BDM-IN connector.

Any of these tools can be used to assist in creating and debugging your program stored in

either internal RAM ($800-$C00) or external RAM (U4/U5 see Memory Map).

After satisfactory operation running under a debugger, your program can be written to the

Internal Flash Memory by relocating its start address to $8000 and programming it using

either the included programming utilities or a BDM. Your program will then run automatically

whenever the board is powered on or RESET is applied.

Option jumpers and switches on the board allow for easy transition from one memory type to

another and restoring an operating monitor.

TUTORIAL

This section was written to help you get started developing software with the CME-12B/BC

board. Be sure to read the rest of this manual as well as the documentation on the disk if you

need further information.

The following sections take you through the complete development cycle of a simple "hello

world" program, which sends the string "Hello World" to the serial port.

Creating source code

You can write source code for the CME-12B/BC board using any language that compiles to

Motorola 68HC12 instructions. Included on the software disk is a free Assembler and also a

freeware C compiler and Basic compiler.

You can write your source code using any ASCII text editor. You can use the free EDIT or

NOTEPAD programs that come with your computer. A better code editor can be downloaded

at: http://www.winedit.com. Once your source code is written and saved to a file, you can

assemble or compile it to a Motorola S-Record (hex) format. This type of output file usually

has a .MOT, .HEX or .S19 file extension and is in a format that can be read by the

programming utilities to be programmed into the CME-12B/BC board.

It's important to understand your development board's use of Memory and Addressing when

writing source code so you can locate your code at valid addresses. For example, when in

debug mode, you should put your program CODE in External RAM. In assembly language,

you do this with ORG statements in your source code. Any lines following an ORG statement

will begin at that ORG location, which is the first number following the word ORG, for example:

ORG $2000.

You must start your DATA (or variables) in a RAM location unused by your program, for

example: ORG $1000. When finished debugging, you must change these ORG statements so

that your program is moved to a valid EEPROM area - somewhere after hex 8000. Do this by

putting an ORG $8000 in front of your Program CODE. Data may remain where it is or be

moved down to internal RAM starting at ORG $800. You must also program the STACK

instruction as the first instruction in your program code: LDS #$0BFF.

A look at the example programs on the disk can make all of this clearer. If you're using a

compiler instead of an assembler, consult the compiler documentation for methods used to

locate your code and data.

Source code created to run under the D-bug12 monitor environment will be slightly different

than code written for stand-alone operation. The monitor contains interrupt and RESET

vectors that your code must provide when it's no longer running under the monitor. See the

Programming Flash EEPROM section for more information on this.

Assembling source code

An example program called “HELLO.ASM” is provided under the \EXAMPLE directory.

You can assemble your source code using command line tools under a DOS prompt by typing:

AS12 HELLO.ASM –LHELLO

Most compilers and assemblers allow many command line options so using a MAKE utility or

batch file is recommended if you use this method. Run AS12 without any arguments to see all

the options, or see the AS12.TXT file on the disk.

The programming utilities provided with this board also contain a simple interface to the free

assembler. Use it by selecting "Build" or “Assembler” from the menu. This will prompt you for

the file to be assembled.

DO NOT use long path names (> 8 characters). The free assembler is an old DOS tool that

does not recognize them.

If there are no errors in your source code, 2 output files will be created:

HELLO.S19 a Motorola S-Record file that can be programmed into memory

HELLO.LST a common listing file which shows the relationship between source

and output

The listing file is especially helpful to look at when debugging your program. If your program

has errors, they will be displayed and no output will be generated, otherwise the listing file will

be displayed.

If you prefer a windows integrated programming environment – try the Motorola MCU-EZ

tools. Refer to the MCU-EZ documentation on the disk for more information.

Also, a port for the free GNU C compiler and tools for the HC12 is in the works and may be

finished as you read this. Check www.axman.com or :

http://home.worldnet.fr/~stcarrez/m68hc11_port.html

Running your application

After creating an S-Record file you can "upload" it to the development board for a test run.

The provided example “HELLO.ASM” was created to run from RAM so you can use the D-

Bug12 Monitor to test it without programming it into EEPROM.

If you haven’t done so already, verify that the CME-12B/BC board is connected and operating

properly by following the steps under “GETTING STARTED” until you see the D-Bug12

prompt, then follow these steps to run your program:

1. Press and release the RESET button on the CME-12B/BC board. You should see the

PRESS ANY KEY message. Hit the return key ↵to get the monitor prompt.

2. Type LOAD ↵↵

This will prepare D-Bug12 to receive a program.

3. Select Upload or Send and when prompted for a file name select your assembled program

file in s-record format that was created in the previous section called: HELLO.S19

Your program will be sent to the board thru the serial port.

4. When finished loading you will see the > prompt again.

Type CALL 1000 ↵↵

This tells D-Bug12 to execute the subroutine at address $1000, which is the start of our

test program.

5. If everything is working properly you should see the message “Hello World” echoed back

to your terminal screen then, since we return at then end of our program, a line containing

the internal register status displayed by D-Bug12 and a message prompt.

6. If you do not get this message, try going thru this tutorial once more, then if still no go, see

the TROUBLESHOOTING section in this manual

You can modify the hello program to display other strings or do anything you want. The

procedures for assembling your code, uploading it to the board and executing it remain the

same. D-Bug12 has many powerful features such as breakpoints, assembly/disassembly,

memory dump and modify and program trace. Type HELP at the D-Bug12 prompt for a listing

of commands or consult the D-Bug12 documentation on the disk for more information.

Programming Flash EEPROM

You can program your application into EEPROM so it executes automatically when you apply

power to the board as follows:

1. Make a backup copy of HELLO.ASM then use a text editor to modify it. Change the start

of the program to $8000 which is the beginning of the EEPROM. Do this by changing the

”ORG $1000” to ”ORG $8000”.

2. Remove the comment ;character from before the following line to initialize the stack

pointer which is necessary when running outside of D-Bug12:

LDS #$C00 ; initialize the stack pointer

3. Add a comment ;character to the beginning of the first RTS statement, which will cause

the program to end gracefully with an endless loop:

; RTS ; return (use this only if called, from monitor

bra ENDPROG ; endless loop

4. Remove the comment ;character from before the following 2 lines at the end, to set the

reset vector to go to the beginning of the program (the label START) when powered on:

org $fffe reset vector

fdb START

5. Re-Assemble HELLO.ASM as described in the "Assembling Source Code" section.

6. Select “CME12BC” under AxIDE.

7. Select the “Program” option and when prompted for a file name, enter the new

HELLO.S19 file then select [OK].

8. Set the CONFIG SWITCH positions 1,2,3,4 and 6 to ON.

9. Press the RESET button on the board then select Continue or hit ENTER. A new utilities

menu should be displayed. If you have trouble here, see the TROUBLESHOOTING

section.

10. Set the CONFIG SWITCH position 5 ON. The red VPP light should come on.

11. When prompted to “Erase” choose Yes.

12. When finished programming, set the CONFIG SWITCH positions 1,2,3,4 and 5 OFF. The

VPP light should turn off.

13. Cycle power or press RESET on the board. Your new program should start automatically

and the “Hello World” prompt should be displayed in the terminal window.

To return to the D-Bug12 monitor program, set the CONFIG SWITCH positions 1,2,3 and 4

back ON then press RESET.

MEMORY MAP

Following is the default memory map for this development board. Consult the HC12 technical

reference manual on the support disk for details of the internal memory map for the processor.

FFFF

FFFE RESET Vector Address

8000

- - - - - - - - - - - - - - - - - - - - -

CONFIG SWITCH 1 2 3 4

ON ON ON ON External EPROM U6/7 (Debug12)

ON ON ON OFF External SRAM U4/5

OFF OFF OFF OFF Internal Flash EEPROM

7FFF

1000

External RAM in U4/5 with CONFIG 1 - 4 ON

FFF

D00 HC12 Internal EEPROM

CFF

C00 External RAM in U4/5 with CONFIG 1 - 4 ON

BFF

800 Internal RAM

7FF

400 External RAM in U4/5 with CONFIG 1 - 4 ON

Peripheral Area

3FF

200

Unused = 280-3FF

LCD / CS7 = 270-27F

CS6 = 260-26F

CS5 = 250-25F

CS4 = 240-24F

CS3 = 230-23F

CS2 = 220-22F

CS1 = 210-21F

CS0 = 200-20F

1FF

000 68HC12 Internal Registers

See 68HC12 Technical Reference Manual

CONFIG SWITCH

The CME-12B/BC board is shipped from the manufacturer with the following default CONFIG

SWITCH settings:

1234 567 8

ON ON ON ON OFF ON OFF OFF

The 8 position CONFIG SWITCH provides an easy method of configuring the CME-12B/BC32

board operation. Following are the configuration switch descriptions and HC12 I/O port

usage:

CONFIG

SWITCH OPERATION when in ON position HC12 I/O PORT USED

1MODE A selection (see Mode chart

below) MODA / PE5

2MODE B selection (see Mode chart

below) MODB / PE6

3EXT –External Memory enable (1) N/A

4MON –Monitor Memory enable (2) N/A

5VPP - Flash VPP voltage enable N/A

6RXD - Serial Port RXD input enable PS0 / RXD

7PC0 –CAN Port RXCAN enable PC0

8PC1 –CAN Port TX enable PC2

(1) Enables memory bus operation for access to board memory. Expanded bus must be

on for proper operation.

(2) Enables monitor EPROM’s in memory map at 0x8000 – FFFF hex if CONFIG

SWITCH position 3 is also on. When in off position memory space is SRAM for BDM

use.

MODE CHART

Single Chip Mode A and B = OFF

Expanded Wide Mode A and B = ON

MEM-SEL JUMPERS

Memory sockets U4/5 are shipped with 32K byte RAM devices. U6/7 are shipped with 32K

byte EPROM devices programmed with the D-bug12 monitor.

1,3,4 IN: enables RAM or EEPROM, 32K devices to U6/7

1,3 IN: enables RAM or EEPROM, 8K devices in U6/7

2,4 IN: enables EPROM, 8K or 32K devices in U6/7 (Default)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Motorola Computerhardware Handbücher

Motorola

Motorola MPC8260 PowerQUICC II Bedienungsanleitung

Motorola

Motorola MC68030 Bedienungsanleitung

Motorola

Motorola NXP SYMPHONY DSP56007 Gebrauchsanweisung

Motorola

Motorola M68060 Bedienungsanleitung

Motorola

Motorola Starline SG1000 Bedienungsanleitung

Motorola

Motorola M68EM05A24 Bedienungsanleitung

Motorola

Motorola MMCMPFB1200 Bedienungsanleitung

Motorola

Motorola M68HC08 Bedienungsanleitung

Motorola

Motorola M6800 EXORciser Bedienungsanleitung

Motorola

Motorola M68MPB16Y1 Bedienungsanleitung

Motorola

Motorola CPU32 Bedienungsanleitung

Motorola

Motorola Expedience PCC-2510 Bedienungsanleitung

Motorola

Motorola DragonBall MC9328MX1 Bedienungsanleitung

Motorola

Motorola VME/10 Bedienungsanleitung

Motorola

Motorola CMOS Logic Bedienungsanleitung

Motorola

Motorola 56F805 Gebrauchsanweisung

Motorola

Motorola DigitalDNA MPC180E Bedienungsanleitung

Motorola

Motorola Clearwire Bedienungsanleitung

Motorola

Motorola M68MPB916X1 Bedienungsanleitung

Motorola

Motorola MC68020 Bedienungsanleitung

Motorola

Motorola MPC823e Bedienungsanleitung

Motorola

Motorola 68HC12 Bedienungsanleitung

Motorola

Motorola STU-III/R Bedienungsanleitung

Motorola

Motorola MVME3600 Series Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung