Motorola SURFboard SVG2500 Betriebsanleitung

Software License, Warranty, Safety, and Regulatory Information

SVG2500 SURFboard®Wireless Voice Gateway

SAFETY AND REGULATORY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS — when using your telephone equipment, basic safety

precautions should always be followed to reduce the risk of fire, electric shock, and injury to

persons, including the following:

•Read all of the instructions listed here and/or in the user manual before you operate this

device. Give particular attention to all safety precautions. Retain the instructions for future

reference.

•This device must be installed and used in strict accordance with manufacturer’s instructions

as described in the user documentation that is included with the device.

•Comply with all warning and caution statements in the instructions. Observe all warning and

caution symbols that are affixed to this device.

•To prevent fire or shock hazard, do not expose this device to rain or moisture. The device

must not be exposed to dripping or splashing. Do not place objects filled with liquids, such

as vases, on the device.

•This device was qualified under test conditions that included the use of the supplied cables

between systems components. To ensure regulatory and safety compliance, use only the

provided power and interface cables and install them properly.

•Different types of cord sets may be used for connections to the main supply circuit. Use

only a main line cord that complies with all applicable device safety requirements of the

country of use.

•Installation of this device must be in accordance with national wiring codes and conform to

local regulations.

•Operate this device only from the type of power source indicated on the device’s marking

label. If you are not sure of the type of power supplied to your home, consult your dealer or

local power company.

Software License, Warranty, Safety, and Regulatory Information

SVG2500 SURFboard®Wireless Voice Gateway

•Do not overload outlets or extension cords, as this can result in a risk of fire or electric

shock. Overloaded AC outlets, extension cords, frayed power cords, damaged or cracked

wire insulation, and broken plugs are dangerous. They may result in a shock or fire hazard.

•Route power supply cords so that they are not likely to be walked on or pinched by items

placed upon or against them. Pay particular attention to cords where they are attached to

plugs and convenience receptacles, and examine the point where they exit from the device.

•Place this device in a location that is close enough to an electrical outlet to accommodate

the length of the power cord.

•Place device to allow for easy access when disconnecting the power cord of the device

from the AC wall outlet.

•Do not connect the plug into an extension cord, receptacle, or other outlet unless the plug

can be fully inserted with no part of the blades exposed.

•Place this device on a stable surface.

•It is recommended that the customer install an AC surge protector in the AC outlet to which

this device is connected. This is to avoid damaging the device by local lightning strikes and

other electrical surges.

•Postpone installation until there is no risk of thunderstorm or lightning activity in the area.

•Avoid using a telephone (other than a cordless type) during an electrical storm. There may

be a remote risk of electric shock from lightning. For added protection, unplug the device

from the wall outlet and disconnect the cables to avoid damage to this device due to

lightning and power surges.

•Do not cover the device, or block the airflow to the device with any other objects. Keep the

device away from excessive heat and humidity and keep the device free from vibration and

dust.

•Wipe the device with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do

not spray cleaners directly on the device or use forced air to remove dust.

•CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger (e.g., 24 AWG) UL

Listed or CSA Certified Telecommunication Line Cord, or national equivalent.

•Disconnect TNV circuit connector(s) before disconnecting power.

•Disconnect TNV circuit connector before removing cover.

Software License, Warranty, Safety, and Regulatory Information

SVG2500 SURFboard®Wireless Voice Gateway

•Do not use this product near water; for example, near a bathtub, washbowl, kitchen sink or

laundry tub, in a wet basement, or near a swimming pool.

•Do not use the telephone to report a gas leak in the vicinity of the leak.

•Use only the power cord and batteries indicated in this manual. Do not dispose of batteries

in a fire. They may explode. Check with local codes for possible disposal instructions.

•Upon completion of any service or repairs to this device, ask the service technician to

perform safety checks to determine that the device is in safe operating condition.

•Do not open the device. Do not perform any servicing other than that contained in the

installation and troubleshooting instructions. Refer all servicing to qualified service

personnel.

SAVE THESE INSTRUCTIONS

Note to CATV System Installer — This reminder is provided to call the CATV system installer’s

attention to Section 820.93 of the National Electric Code, which provides guidelines for proper

grounding and, in particular, specifies that the Coaxial cable shield shall be connected to the

grounding system of the building, as close to the point of cable entry as practical.

Software License, Warranty, Safety, and Regulatory Information

SVG2500 SURFboard®Wireless Voice Gateway

Safety Requirements for the SVG2500 Lithium-Ion Battery

You must properly handle the SVG2500 lithium-ion rechargeable battery to ensure your safety.

Improper handling can cause leakage, heat, smoke, explosion, or fire resulting in damage to the

equipment or the user.

•Use the SVG2500 battery only in the SVG2500 SURFboard Wireless Voice Gateway.

•CAUTION: Risk of explosion if battery is replaced by the incorrect type. Use only Motorola

approved batteries, Motorola part number 515757-001 and 538043-001. Dispose of used

batteries according to the instructions.

•Do not use the battery where static electricity is generated.

•Do not heat the battery or discard into a fire. Keep the battery away from high-temperature

locations.

•Properly discard the battery if it exhibits an abnormal condition, such as heat, odor, color, or

a change in shape. When discarding, place insulated tape over the battery terminals.

•The battery should be stored out of the reach of children.

•Do not store the battery close to metal objects.

•If the battery leaks fluid and you touch it, immediately wash your hands. If the fluid gets into

your eye, do not rub the eye. Rinse with water and immediately seek medical care. Left

untreated, the battery fluid could cause damage to the eye.

•Ensure that the battery does not receive any strong impacts, such as dropping or striking

with a hard object.

•At the end of battery life, the SVG2500 battery must be disposed of properly and may need

to be recycled. Contact your local recycling center for proper disposal methods.

•Do not expose the battery to ultrasonic energy.

•Do not disassemble, modify, or attempt to repair the battery.

•Before installation, the battery should not be subjected to temperatures below –10ºC or

above +60ºC (14 ºF to 140 ºF). After initial customer usage (initially charged above shipping

charge state), the battery should not be subjected to temperatures outside the operating

temperature range:

Battery Pack External Exposure Operating Temperature Range:

Charging: 0.0 °C to +45.0 °C (0 ºF to 113 ºF)

Software License, Warranty, Safety, and Regulatory Information

SVG2500 SURFboard®Wireless Voice Gateway

Discharging: –10.0°C to +60.0°C (14 ºF to 140 ºF)

NOTE: A backup battery is not available for some models of the SVG2500.

Important VoIP Service Information

When using this VoIP device, you CANNOT make any calls, including an emergency call, and E911

location services WILL NOT be available, under the following circumstances:

•Your broadband ISP connection goes down, is lost or otherwise fails.

•You lose electrical power.

When using this VoIP device, you may be able to make an emergency call to an operator, but

E911 location services may not be available under the following circumstances:

•You have changed the physical address of your VoIP device, and you did not update or

otherwise advise your VoIP service provider of this change.

•You are using a non-U.S. telephone number.

•There are delays in making your location information available in or through the local

automatic location information database.

Note: Your service provider, not Motorola, is responsible for the provision of VoIP telephony

services through this equipment. Motorola shall not be liable for, and expressly disclaims, any

direct or indirect liabilities, damages, losses, claims, demands, actions, causes of action, risks or

harms arising from or related to the services provided through this equipment.

Software License, Warranty, Safety, and Regulatory Information

SVG2500 SURFboard®Wireless Voice Gateway

FCC STATEMENTS

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential environment. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the device off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the device and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must accept

any interference received, including interference that may cause undesired operation.

FCC CAUTION: Any changes or modifications not expressly approved by Motorola for compliance

could void the user’s authority to operate the equipment.

Software License, Warranty, Safety, and Regulatory Information

SVG2500 SURFboard®Wireless Voice Gateway

FCC RADIATION EXPOSURE STATEMENT

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. To comply with the FCC RF exposure compliance requirements, the separation

distance between the antenna and any person’s body (including hands, wrists, feet and ankles)

must be at least 20 cm (8 inches).

This transmitter must not be co-located or operation in conjunction with any other antenna or

transmitter.

The availability of some specific channels and/or operational frequency bands are country

dependent and are firmware programmed at the factory to match the intended destinations. The

firmware setting is not accessible by the end user.

INDUSTRY CANADA (IC) STATEMENT

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the

following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired

operation of the device.

This device has been designed to operate with the antennas listed below, and having a maximum

gain of 2 dB. Antennas not included in this list or having a gain greater than 2 dB are strictly

prohibited for use with this device. The required antenna impedance is 50 ohms.

Antenna(s): Motorola Part # 538707-001

To reduce potential radio interference to other users, the antenna type and its gain should be so

chosen that the equivalent isotropically radiated power (e.i.r.p) is not more than that permitted for

successful communications.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Software License, Warranty, Safety, and Regulatory Information

SVG2500 SURFboard®Wireless Voice Gateway

IC RADIATION EXPOSURE STATEMENT

IMPORTANT NOTE:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20 cm

between the radiator and your body.

WIRELESS LAN INFORMATION

This device is a wireless network product that uses Direct Sequence Spread Spectrum (DSSS)

radio technology. The device is designed to be inter-operable with any other wireless DSSS

product that complies with:

•The IEEE 802.11 Standard on Wireless LANs (Revision B and Revision G), as defined and

approved by the Institute of Electrical Electronics Engineers

•The Wireless Fidelity (Wi-Fi) certification as defined by the Wireless Ethernet Compatibility

Alliance (WECA).

Software License, Warranty, Safety, and Regulatory Information

SVG2500 SURFboard®Wireless Voice Gateway

RESTRICTIONS ON THE USE OF WIRELESS DEVICES

In some situations or environments, the use of wireless devices may be restricted by the

proprietor of the building or responsible representatives of the organization. For example, using

wireless equipment in any environment where the risk of interference to other devices or services

is perceived or identified as harmful.

If you are uncertain of the applicable policy for the use of wireless equipment in a specific

organization or environment, you are encouraged to ask for authorization to use the device prior to

turning on the equipment.

The manufacturer is not responsible for any radio or television interference caused by

unauthorized modification of the devices included with this product, or the substitution or

attachment of connecting cables and equipment other than specified by the manufacturer.

Correction of the interference caused by such unauthorized modification, substitution, or

attachment is the responsibility of the user.

The manufacturer and its authorized resellers or distributors are not liable for any damage or

violation of government regulations that may arise from failing to comply with these guidelines.

SECURITY WARNING: This device allows you to create a wireless network. Wireless network

connections may be accessible by unauthorized users. Please read the SVG2500 User Guide or

visit the Motorola website to learn how to protect your network:

Software License, Warranty, Safety, and Regulatory Information

SVG2500 SURFboard®Wireless Voice Gateway

INTERNATIONAL DECLARATION OF CONFORMITY

We,

Motorola, Inc.

101 Tournament Drive

Horsham, PA, U.S.A.

Declare under our sole responsibility that the

SVG2500 SURFboard Wireless Voice Gateway Series

To which the declaration relates is in conformity with the following standards:

EN 60950-1

EN 300 328

EN 301 489-1/-17

EN 61000-3-2

EN 61000-3-3

The following provisions of the Directive(s) of the Council of the European Union:

EMC Directive 2004/108/EC

Low Voltage Directive 2006/95/EC

R&TTE Directive 1999/5/EC

Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC

Restriction of the Use of Certain Hazardous Substances in Electrical Equipment (RoHS) Directive 2002/95/EC

CARING FOR THE ENVIRONMENT BY RECYCLING

When you see this symbol on a Motorola product, do not dispose of the product with residential

or commercial waste.

Recycling your Motorola Equipment

Please do not dispose of this product with your residential or commercial waste. Some countries

or regions, such as the European Union, have set up systems to collect and recycle electrical and

electronic waste items. Contact your local authorities for information about practices established

for your region. If collection systems are not available, call Motorola Customer Service for

assistance.

www.motorola.com/recycle

Andere Handbücher für SURFboard SVG2500

Inhaltsverzeichnis

Andere Motorola Tor Handbücher

Motorola

Motorola SURFboard SVG7782 Bedienungsanleitung

Motorola

Motorola Vonage VT2142 Bedienungsanleitung

Motorola

Motorola RG2200 Bedienungsanleitung

Motorola

Motorola CLEARTONE CM5000 Bedienungsanleitung

Motorola

Motorola NC800 Bedienungsanleitung

Motorola

Motorola EASY START KIT HMEZ1000 - CELL PHONE SET UP Bedienungsanleitung

Motorola

Motorola SURFboard SBG901 Bedienungsanleitung

Motorola

Motorola Netopia 2247-62 Bedienungsanleitung

Motorola

Motorola HMUG1080 Bedienungsanleitung

Motorola

Motorola Netopia Series Bedienungsanleitung

Motorola

Motorola RSG2500 Bedienungsanleitung

Motorola

Motorola WIRELESS CABLE MODEM GATEWAY SBG900 -... Konfigurationshandbuch

Motorola

Motorola SURFboard SBG6782-AC Bedienungsanleitung

Motorola

Motorola Netopia 3387WG-VGx Bedienungsanleitung

Motorola

Motorola NETOPIA 2210-02 Bedienungsanleitung

Motorola

Motorola NVG510 Bedienungsanleitung

Motorola

Motorola Netopia 7347-84 Bedienungsanleitung

Motorola

Motorola Netopia 2247-42 Bedienungsanleitung

Motorola

Motorola VT2442 - VONAGE Bedienungsanleitung

Motorola

Motorola NETOPIA 2210-02 ADSL2-RESIDENTIAL GATEWAY -... Bedienungsanleitung

Motorola

Motorola SURFboard eXtreme SBG6782-AC Bedienungsanleitung

Motorola

Motorola Netopia Bedienungsanleitung

Motorola

Motorola Netopia 3347-02 Bedienungsanleitung

Motorola

Motorola SURFboard SBG901 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung