Motorola Symbol IP54 Konfigurationshandbuch
One Symbol Plaza, Holtsville, NY 11742-1300 • 1.631.738.2400 • www.symbol.com
Cleaning Instructions for
Symbol IP54 Devices
Purpose:
The purpose of this document is to demonstrate the proper methods and solutions to clean Symbol
mobile computer IP54 devices as well as their respective cradles.
Materials used:
•Alcohol wipes
•Lens tissue
•Cotton tipped applicators (Puritan)
•Isopropyl Alcohol or any solution containing ethanol
•Can compressed air with a tube (Micro Blast)
Cleaning the Mobile Computer
Mobile Computer Plastic Housing
Using the alcohol wipes, wipe:
•The front of the device including keys and in- between keys
•back of the device
•sides of the device
•top of the device
•bottom of the device
One Symbol Plaza, Holtsville, NY 11742-1300 • 1.631.738.2400 • www.symbol.com
Display
The display can be wiped down with the alcohol wipe indicated above, but care should be taken not
to allow any pooling of liquid around the edges of the display. Immediately dry the display with a soft,
non-abrasive cloth to prevent streaking.
Scanner Exit Window
Wipe the scanner exit window periodically with a lens tissue or other material suitable for cleaning
optical material such as eyeglasses.
Connector
1- Remove the main battery from mobile computer. Refer to the devices’ User Guide for
instructions.
2- Close battery door.
3- Dip the cotton portion of the cotton tipped applicator in isopropyl alcohol.
4- Insert the cotton portion of the cotton tipped applicator inside the connector on the bottom of
the mobile computer as shown below. Ensure the tip of the cotton applicator touches the back
of the connector. Do not leave any cotton residue inside the connector.
5- Twist the cotton tipped applicator and slowly move it back-and-forth from one side of the
connector to the other. Repeat at least three times then remove cotton tipped applicator from
the connector.
6- Use the cotton tipped applicator dipped in alcohol to remove any grease and dirt near the
connector area.
7- Use a dry cotton tipped applicator and repeat steps 3 through 5.
One Symbol Plaza, Holtsville, NY 11742-1300 • 1.631.738.2400 • www.symbol.com
8- Spray compressed air in the connector area by pointing the tube/nozzle about ½ inch away
from the surface. Caution: Do not point nozzle at yourself and others, ensure the nozzle or
tube is away from your face.
9- Inspect the area for any grease or dirt, repeat steps 3 to step 8 as required.
10-Ensure that there is no lint left by the cotton tipped applicator. Remove lint if found.
One Symbol Plaza, Holtsville, NY 11742-1300 • 1.631.738.2400 • www.symbol.com
Cleaning Cradle Connector
1- Remove the DC power cable from the cradle.
2- Position the cradle as shown below.
3- Dip the cotton portion of the cotton tipped applicator in isopropyl alcohol.
4- Rub the cotton portion of the cotton tipped applicator along the pins of the connector as shown
below. Slowly move the applicator back-and-forth from one side of the connector to the other.
Do not let any cotton residue on the connector.
One Symbol Plaza, Holtsville, NY 11742-1300 • 1.631.738.2400 • www.symbol.com
5- All sides of the connector (shown below) should also be rubbed with the cotton tipped
applicator.
6- Spray compressed air in the connector area by pointing the tube/nozzle about ½ inch away
from the surface. Caution: do not point nozzle at yourself and others, ensure the nozzle or tube
is pointed away from your face.
7- Ensure that there is no lint left by the cotton tipped applicator, remove lint if found.
8- If grease and other dirt can be found on other areas of the cradle, use lint free cloth and
alcohol to remove.
9- Allow at least 10 to 30 minutes (depending on ambient temperature/humidity)* for the alcohol
to air dry before applying power to cradle.
10-If the temperature is low and humidity is high, longer drying time is required. Warm
temperature and dry humidity requires less drying time. DO NOT PLACE PRODUCTS IN AN
OVEN OR UNDER HEAT LAMPS!
Cleaning Frequency
The frequency of these cleanings is up to the customer’s discretion due to the varied environments in
which the mobile computers are used. They may be cleaned as frequently as required. However
when used in dirty environments it may be advisable to periodically clean the scanner exit window to
ensure optimum scanning performance.
Caution:
•Always wear eye protection
•Read warning label on compressed air and alcohol product before using.
•If you have to use any other solution for medical reasons please contact Symbol for more
information.
WARNING! Avoid exposing this product to contact with hot oil or other flammable liquids. If such exposure occurs, unplug the unit and
clean the product immediately in accordance with these guidelines.
Inhaltsverzeichnis
Andere Motorola Handheld Handbücher
Motorola
Motorola FR68 Series Bedienungsanleitung
Motorola
Motorola MC919Z Montageanleitung
Motorola
Motorola MC9094-KUCHJERA6WR - MC9094-K - Win Mobile 6.1 Professional 624... Bedienungsanleitung
Motorola
Motorola 7545MBW Bedienungsanleitung
Motorola
Motorola MC3000 Bedienungsanleitung
Motorola
Motorola TETRA MTM800 Bedienungsanleitung
Motorola
Motorola MC67 Bedienungsanleitung
Motorola
Motorola MC21XX SERIES Montageanleitung
Motorola
Motorola Omnii Bedienungsanleitung
Motorola
Motorola FR6876 Bedienungsanleitung
Motorola
Motorola MC9500-K - Win Mobile 6.1 806 MHz Bedienungsanleitung
Motorola
Motorola MC5590 Bedienungsanleitung
Motorola
Motorola MOTOTRBO MC1000 Bedienungsanleitung
Motorola
Motorola MC9500-K - Win Mobile 6.1 806 MHz Benutzerhandbuch
Motorola
Motorola MOTOPro MPx Bedienungsanleitung
Motorola
Motorola MC9500-K - Win Mobile 6.1 806 MHz Bedienungsanleitung
Motorola
Motorola F4705A Bedienungsanleitung
Motorola
Motorola MC92N0-G Bedienungsanleitung
Motorola
Motorola MC3090Z Bedienungsanleitung
Motorola
Motorola MC75A Bedienungsanleitung
