Mountz FGA V2 Bedienungsanleitung

SILICON VALLEY HEADQUARTERS

1080 North 11th Street, San Jose, CA 95112 | Phone: (408) 292

FGA

ADJUSTABLE

OPERATING INSTRUCTIO

Rev 1.0 (6/15/2022)

How to Indentify a FGA v2 model

There are two ways to identify whether you have a v2 or a v1 model.

The v2 models has separate battery access cover (see page 2) on the lower side of the

handle. The v1 models does not.

Second option is to move the locking bar

knob (CCW direction) below the torque range capacity. Once you pass the letter "L," if it

displays a firmware version, the model is a v2 model.

Power on Display

Press the black lever button to view the d

igital display and current tool

Sleep Mode

When there is no activity of pressing the lever butting or adjusting the setting,

the display will timeout approximately within 20 seconds and then goes into

Sleep mode. Press the black lever button to aw

Adjusting the Torque Setting

Units of Measurement

Press the black lever button

while the display is powered on

torque measurement unit options available

for

FGA Models

Torque Measurement Units

FGA-8, FGA-20 & FGA-40

ozf.in, lbf.in, cN.m, N.m, kgf.cm

FGA-80

Torque Setting

Slide the locking bar slide mechanism to the unlock position. Use the black adjustment knob to change torque settings. Turn

the knob clockwise to

increase torque and counterclockwise to decrease torque. After selecting your torque value, release the

locking bar slide, and it will return to its original position.

bottom-up.

1080 North 11th Street, San Jose, CA 95112 | Phone: (408) 292

-2214 | Fax: (408) 292-2733 | mountztorque.com

ADJUSTABLE

TORQUE

SCREWDRIVER

OPERATING INSTRUCTIO

There are two ways to identify whether you have a v2 or a v1 model.

The v2 models has separate battery access cover (see page 2) on the lower side of the

Second option is to move the locking bar

slide into the unlock position and adjust the

knob (CCW direction) below the torque range capacity. Once you pass the letter "L," if it

displays a firmware version, the model is a v2 model.

igital display and current tool

setting.

When there is no activity of pressing the lever butting or adjusting the setting,

the display will timeout approximately within 20 seconds and then goes into

Sleep mode. Press the black lever button to aw

ake the tool from Sleep mode.

while the display is powered on

to toggle through

for

your FGA model.

Torque Measurement Units

ozf.in, lbf.in, cN.m, N.m, kgf.cm

lbf.in, N.m, kgf.cm

Slide the locking bar slide mechanism to the unlock position. Use the black adjustment knob to change torque settings. Turn

increase torque and counterclockwise to decrease torque. After selecting your torque value, release the

locking bar slide, and it will return to its original position.

Per ISO:6789-

1, when certified, the tool is adjusted from the

v1 model

v2 model

SCREWDRIVER

(V2)

Slide the locking bar slide mechanism to the unlock position. Use the black adjustment knob to change torque settings. Turn

increase torque and counterclockwise to decrease torque. After selecting your torque value, release the

1, when certified, the tool is adjusted from the

SILICON VALLEY HEADQUARTERS

1080 North 11th Street, San Jose, CA 95112 | Phone: (408) 292-2214 | Fax: (408) 292-2733 | mountztorque.com

Note: Do not adjust torque above or below the designated torque ranges for the torque screwdriver. If you exceed the upper

torque range capacity of the screwdriver, the tool's screen will display the letter "H." If you exceed the lower torque range

capacity of the screwdriver, the tool's screen will display the letter "L."

Torque Setting Increments

The screwdriver's torque settings are selectable in increments.

FGA-8 FGA-20

FGA-40 FGA-80

Applying Torque

1. Tighten the fastener or bolt by applying a steady twist. Keep the screwdriver in line with the axis of the bolt during

tightening. The screwdriver will ‘slip’ after achieving the pre-set torque setting.

2. The screwdriver will automatically reset itself for the next application.

3. With its unique cam-over design, it’s impossible to over-tighten beyond the pre-set load.

Units Increments

ozf.in 0.5

lbf.in 0.02

cN.m 0.5

N.m 0.005

kgf.cm 0.05

Units Increments

ozf.in 1

lbf.in

(Settings < 5 lbf.in)

(Settings > 5 lbf.in)

cN.m 1

N.m 0.01

kgf.cm 0.1

Units Increments

ozf.in 2.5

lbf.in

0.1

cN.m 2

N.m 0.02

kgf.cm 0.2

Units Increments

ozf.in -------

lbf.in

(Settings < 40 lbf.in) 0.5

(Settings > 40 lbf.in) 1.0

cN.m -------

N.m

(Settings < 2 N.m) 0.02

(Settings > 2 N.m) 0.05

kgf.cm

(Settings < 45 kgf.cm) 0.5

(Settings > 45 kgf.cm) 1.0

SILICON VALLEY HEADQUARTERS

1080 North 11th Street, San Jose, CA 95112 | Phone: (408) 292-2214 | Fax: (408) 292-2733 | mountztorque.com

Battery

When a low battery status is detected, the FGA will indicate it by displaying "bAt" on the

screen. The battery needs to be replaced.

Note: The FGA doesn't have a battery status icon that displays the battery level status

permanently. The low battery indicator will only display once the estimated battery life is <10%

Battery Replacement

1. Use a 1.5mm hexagonal key to loosen the two screws and remove

the battery cover.

2. Remove the battery from the battery holder.

3. Insert a new battery.

Battery (CR1225) for FGA v2

Mountz Item # 982-000025

4. Install a battery cover.

Maintenance Schedule

Like an automobile, torque screwdrivers contain moving parts that require periodic servicing and lubrication.

Expected Tool Life

With normal use – 1,000,000 operations

Routine Maintenance

After 100,000 operations, strip, clean and re-grease the spring, bearings and internal components. Any worn components

should be replaced.

Note: Any tool that is dismantled during its life must be re-lubricated in accordance with the Mountz recommendations. Do not

clean tools by immersing them in a solvent, as this will destroy the internal lubrication and cause the failure of the tool.

Period Between Recalibration

20,000 fastening operations. It is acknowledged that some tools may achieve 20,000 operations in a relatively short period of

time. Under these circumstances, the user may decide to increase the period between calibration intervals with the benefit of

their experience.

Remove screws Remove & insert battery

SILICON VALLEY HEADQUARTERS

1080 North 11th Street, San Jose, CA 95112 | Phone: (408) 292-2214 | Fax: (408) 292-2733 | mountztorque.com

Calibrating Torque Screwdrivers

Please view the FGA calibration instructions document.

Warranty

Mountz FGA tools are the only cam-over drivers on the market to offer a two-year unlimited warranty. If it breaks in any way,

we’ll fix it or replace it for free.

Lifetime guarantee against manufacturing defects. We only make the highest quality products. This driver will not have a

defect, we stake our quality reputation on it.

Warranty does not include battery replacement.

Testing and Servicing

Torque tools go out of calibration with use. Calibrating a torque tool is a fine-tuning process of bringing the tool back within its

tolerance. Regular torque calibration of a hand screwdriver ensures accuracy, repeatable tool performance, and adherence to

international standards.

We recommend a general once a year calibration interval. However, it is the user’s organization that must determine suitable

intervals based upon equipment performance, application, degree of usage and management objectives.

Mountz Calibration and Repair Services

Mountz Inc. features an experienced calibration and repair staff. Our trained technicians can calibrate and repair most any

tool. Mountz provides rapid service with quality that you can trust as we offer two state-of-the-art calibration lab and repair

facilities that can calibrate up to 20,000 lbf.ft.

About Mountz

Mountz, The Torque Tool Specialists®, has been a leader in the torque tool industry for more than 55 years. Engineered in the

Silicon Valley and serving the globe, Mountz focuses on delivering high-quality torque products, services, and solutions to

ensure customers can always proceed with confidence. We are committed to forging a safer world through precision and

accuracy and by innovating every day.

Mountz Service Locations

Eastern Service Center

19051 Underwood Rd.

Foley, AL 36535

Phone: (251) 943-4125

Fax: (251) 943-4979

Western Service Center

1080 N.11th Street

San Jose, CA 95112

Phone: (408) 292-2214

Fax: (408) 292-2733

UK Service Center

Pier Copse Courtyard, Milland Lane,

Liphook, Hampshire, GU30 7JN, UK

Phone: 00 44 1428 741756

www.mountztorque.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mountz Akkuschrauber Handbücher

Mountz

Mountz NF Series Bedienungsanleitung

Mountz

Mountz BL-2000 Bedienungsanleitung

Mountz

Mountz Ergo Micro Torque Bedienungsanleitung

Mountz

Mountz fleX Power XP35P Bedienungsanleitung

Mountz

Mountz FLEXPOWER FLEXC-3PX Bedienungsanleitung

Mountz

Mountz K150F-A Bedienungsanleitung

Mountz

Mountz HDC-40i Bedienungsanleitung

Mountz

Mountz EMT 6 Bedienungsanleitung

Mountz

Mountz E-Drive E201 Bedienungsanleitung

Mountz

Mountz BLG-4000 Bedienungsanleitung

Mountz

Mountz TLS Standard Bedienungsanleitung

Mountz

Mountz BLG-BC1 Series Bedienungsanleitung

Mountz

Mountz FG Bedienungsanleitung

Mountz

Mountz BF-Series Bedienungsanleitung

Beliebte Akkuschrauber Handbücher anderer Marken

Makita

Makita DFT085F Bedienungsanleitung

Parkside

Parkside 345138 2004 Bedienungsanleitung

Makita

Makita DFL650F Bedienungsanleitung

AEG

AEG BST 18BLX2-0 Bedienungsanleitung

Ingersoll-Rand

Ingersoll-Rand D5000 Series Bedienungsanleitung

BGS technic

BGS technic 956 Bedienungsanleitung

Hilti

Hilti SD 6000 Bedienungsanleitung

Parkside

Parkside PEPS 3 A1 Bedienungsanleitung

Festool

Festool TI 15 Bedienungsanleitung

Makita

Makita DWT190 Bedienungsanleitung

Matatakitoyo Torque Tools

Matatakitoyo Torque Tools MTD Bedienungsanleitung

Skil

Skil 2346 Montageanleitung

DeWalt

DeWalt XR LI-ION DCD931 Bedienungsanleitung

Festool

Festool DWC 18-2500 Bedienungsanleitung

EINHELL

EINHELL TE-CD 12/1 Li Series Bedienungsanleitung

Makita

Makita BFT043F Bedienungsanleitung

Atlas Copco

Atlas Copco LUM12 SR Merkblatt

FAR

FAR TECNUM Gebrauchs- und Pflegehandbuch