Mountz EZ-TorQ II Bedienungsanleitung

Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: (408) 292-2214 Fax: (408) 292-2733

www.mountztorque.com

Operating Instructions

Version 3.2 (3/22/2017)

Features

Page 2

Heading Page

Screen Display 4

Mounting 4

Menu Selections (Units, Mode, Set-Up, Quick Test & Filter) 5-7

Enter Key & Mode Selection 7

Set-Up Selections (Direction, Data Output, Contrast, Language, Sleep, Backlight, 8-10

Clear Memory, Auto Clear & Tolerance)

Filter Selections 11

External Connection 12

Power Tool Testing 12

EZ-TorQ Meter Interface Software 13-14

Com Port Selection 15

Quick Test Downloading 16

Data Logging 17

Bootloader 18

Battery Operation/Universal Charger 19

Accessories 20

System Accuracy +/- 0.5% of reading from 20% to 100% of full scale.

System Accuracy +/- 1% of reading from 10% to 20% of full scale.

Recommended for hand screwdrivers, most wrenches and power tools*

Selection of three operating modes: (Track, Peak and First Peak*)

Seven units of torque measurements: (ozf.in, lbf.in, lbf.ft, cN.m, N.m, kgf.m, kgf.cm).

Features built-in Quick Test operation.

Includes PC Windows based software programs:

EZ-TorQ II Interface Program - to conduct Quick Tool Tests, Data Logging and Sensor Calibration.

“Flash" memory allows upgrades to be done by the user in the field & internet through the RS-232 port.

Easy to use Menu Structure.

Six-digit display.

Ability to download readings to PC via RS-232 or via USB

Real time out via RS-232

High Capacity Li-Ion Batteries for long life.

The unit will store a total of up to 150 data points.

Real time graph of torque vs. time using associated PC Windows software.

Features Go / No Go LEDs that illuminate when high or low tolerance setting is achieved or out of tolerance

Three low-pass filter settings (500, 170 and 130 Hz)*

* Note! - Mountz added these features to the EZ-TorQ II operating system in September 2011. EZ-TorQ II models prior to seri-

al # EZ1108001 do not have these features. If you would like to have your EZ-TorQ II torque tester upgraded to include the

current operating system, please send it to a Mountz Service & Repair facility.

1. New Operating mode: First Peak

2. New low-pass filter settings (500, 170 and 130 Hz)

Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: (408) 292-2214 Fax: (408) 292-2733

www.mountztorque.com

Page 3

Quick Menu Structure Main Display Screen

Peak

23.8 lbf.in

Quick Test Units Mode Setup

Main Menu

lbf.in

lbf.ft

ozf.in

kgf.cm

kgf.m

N.m

cN.m

Track

Peak

Backlight

Clear Memory

Auto Clear

Tolerance

Direction

Contrast

Language

Sub-Menu

Enter

Enter Sleep Mode

Enter

Filter

Pan-Pac

(130 Hz)

Mountz

(170 Hz)

Sub-Menu

Enter

Data Output

ISO

(500 Hz)

First Peak

Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: (408) 292-2214 Fax: (408) 292-2733

www.mountztorque.com

Page 4

Screen Display and Menu Structure

When the torque tester is turned on it will display a

Screen similar to that below for 5 seconds and then

go into Reading Mode.

EZtorQ II

Version 1.03

Sensor Model:

EZtorQ 100i

Serial Number:

EZ-09-05-007

The Reading Mode Screen will appear as shown

below:

Track

+0.0000 Lbf.in

The Menu key is used to access the available menu items. The scroll keys allow scrolling through various menu items.

The Enter key is used to select a menu item and is also used to clear readings from the display if the unit is in Manual

Clear mode.

Scroll keys

It is recommend securing the torque tester to a work-

bench before operating. Immobilizing the analyzer is

critical for the safety of the operator as well as for the

accuracy of torque measurements during operation.

Mounting the unit to a fixed surface offers the most

secure way to immobilize the analyzer, and is

recommended when used at a permanent location. It

employs two spring loaded mounting screws from the

unit into the mounting surface.

Note: Remember that a loose torque tester during utilization can impact the validity of torque readings. Always make

sure the unit is secure before operating, as repeated usage may loosen the screws.

Loosen both

black caps to

access

mounting

screw.

MOUNTING

Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: (408) 292-2214 Fax: (408) 292-2733

www.mountztorque.com

Page 5

Menu Selections

Pressing the "Menu" Key will present the following Screen:

1. Use the Scroll Up or Down key to toggle through: Quick Test, Units, Mode, Setup & Filter.

2. Press Enter key to select a choice.

Setup any operational parameters such as Auto Clear before starting a Quick test as settings cannot

be changed during a Quick Test operation.

1. Press Menu button.

2. With the Quick Test selected, press Enter key

Selecting Quick Test

Once the Quick test is started the "Menu" indication at the bottom left of the EZ-TorQ screen will

change to "Stop". When the desired number of readings are collected, press the Menu key to

end the Quick test.

Quick Test

Units

Mode

Setup

Filter

Quick Test

Units

Mode

Setup

Filter

Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: (408) 292-2214 Fax: (408) 292-2733

www.mountztorque.com

lbf.in

lbf.ft

ozf.in

kgf.cm

kgf.m

N.m

Menu Selections

1. Select Units by highlighting and pressing Enter.

2. Use the Scroll Up or Down key to toggle through the Unit options.

3. Press Enter key to select a Units Setting.

Selecting Units Note:

cN.m is also available but you must

scroll down.

Track

Peak

First Peak

1. Select Mode by highlighting and pressing Enter.

2. Use the Scroll Up or Down key to toggle through the Mode options.

3. Press Enter key to select a Mode Setting.

4. The Main (or reading screen) will display the value of the selected Mode.

Selecting Mode Options

Backlight

First Peak

Data Output

Clear Memory

Auto Clear

Tolerance

Direction

1. Select Setup by highlighting and pressing Enter.

2. Use the Scroll Up or Down key to toggle through the Setup options.

3. Press Enter key to select a Setup Setting.

Selecting Setup

Page 6

Note:

Contrast, Language & Sleep Mode is

also available but you must scroll

down.

Quick Test

Units

Mode

Setup

Filter

Quick Test

Units

Mode

Setup

Filter

Quick Test

Units

Mode

Setup

Filter

Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: (408) 292-2214 Fax: (408) 292-2733

www.mountztorque.com

Pan-Pac (130 Hz)

Mountz (170 Hz)

ISO (500 Hz)

Menu Selections

1. Select Units by highlighting and pressing Enter.

2. Use the Scroll Up or Down key to toggle through the Filter options.

3. Press Enter key to select a Filter Setting.

Selecting Filters

Page 7

Quick Test

Units

Mode

Setup

Filter

Enter Key

The ENTER key function is used for two functions.

CLEARING DISPLAY

The first function is used to clear any torque reading on the display. When the ENTER key is pressed it also sends the

displayed reading to the RS 232 port for printing or downloading to an application program. After sending the data, the

readings will automatically be cleared from the display.

VALIDATING SET-UPS

The other function is the validation of user selection during set-ups (see the Mode Selection, Filter Selection, and the

Units Selection).

Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: (408) 292-2214 Fax: (408) 292-2733

www.mountztorque.com

Page 8

The EZ-TorQ Torque Tester offers three different modes of displaying torque information during operation

(Track, Peak and First Peak). The user will determine which mode is best suited for the application. The use of the three

modes is described below.

TRACK

This mode constantly tracks increasing or decreasing torque

variations. Use this mode to monitor varying torque on motors

and machinery. Also for calibration and testing of dial torque

products (small wrenches or dial screwdrivers).

PEAK

The display retains the highest torque applied. Use this mode

during calibration or testing of any hand type torque wrench

(dial, beam, and screwdriver), as well as power tools.

FIRST PEAK

The display holds the first detected torque peak applied.

Before any torque is applied, the display show dashes in the

torque value area. Once peak is detected, the display will

show the torque value. If a second peak is detected then it

will be displayed in the lower right (in small reverse video).

The function of this mode is primarily used for testing and

calibrating click type mechanical torque wrenches. The

tester captures the point where the wrench first clicks. As

additional force is applied a secondary torque is displayed.

This mode may be used for operator training on the correct

use of operating a click wrench. Always apply torque smoothly

to avoid false first peak readings.

Mode Selection

Track

+12.010 Lbf.in

Peak

+22.350 ozf.in

Setup Selections

This function allows the user to turn on the display backlight for low light

environments.

Use the Up / Down scroll keys to select the desired setting and press

Enter to select the setting.

Backlight

BACKLIGHT SETTING

Backlight: OFF

FPK 500 Hz

+23.615 lbf.in

Menu +24.755

Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: (408) 292-2214 Fax: (408) 292-2733

www.mountztorque.com

Setup Selections

This function allows a user to toggle data output to On or Off. Defaults setting is

Off.

Use the Up / Down Scroll keys to toggle the setting from Off to On. Press enter

to save the setting.

Note! The unit should never be plugged into the Mountz Interface

Program with Data Output turned to "on".

Data Output

This function clears the stored readings from Quick tests. The user will be asked

if they really want to perform this function. If they do they must choose "Yes".

The stored readings can also be deleted from the meter using the EZ Interface

Program.

Scroll to Yes, if you truly desire to clear the readings, and press Enter.

Clear Memory

This function controls the method of clearing the display of torque readings.

When Auto Clear is selected, the torque values, during operation, will automati-

cally be cleared from the display. The user can set the time threshold to control

how long the values should be displayed before clearing. When Manual Clear is

selected, the torque values during operation will indefinitely be display until the

user presses the Enter key. The Auto Clear timer can be set from 1 to 5 seconds.

If a Quick Test is in operation, the readings will be stored when the Auto Clear

timer expires or the user presses Enter if in Manual Clear mode.

Use the Up / Down scroll keys to change between Manual and Auto and press

Scroll Left to move to the Time. Use the Up / Down scroll keys to select the

Time. When finished, press Enter to end the process and store the setting.

Auto Clear

Page 9

Clear Tool Test Results

Are You Sure?

Yes

AUTO CLEAR SETTING

Mode: MANUAL

Time: (seconds) 1

Data Output

Off

This function allows a user to set up the First Peak settings.

Use the Up / Down Scroll keys to toggle between each setting.

Use the Scroll Left set up the data for each setting

Press enter to save the setting.

Note! The unit should never be plugged into the Mountz Interface

Program with Data Output turned to "on".

First Peak

Sensitivity: Low

Min Peak: 5.0089 lbf.in

Units: lbf.in

Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: (408) 292-2214 Fax: (408) 292-2733

www.mountztorque.com

Setup Selections

Allows an operator to set the direction for capturing the torque readings:

(Clockwise, Counter Clockwise and Both directions).

Use the Up / Down scroll keys to change between BOTH, CW and CCW.

When finished, press Enter to end the process and store the setting.

Direction

This function sets the contrast of the Display.

Use the Up scroll key to increase the contrast and the Down scroll key to

decrease the contrast. When finished, press Enter to end the process and store

the setting.

Contrast

Page 10

DIRECTION SETTING

Direction: BOTH

SET LCD CONTRAST

Contrast: 60

The function allows the user to change the language of the meter. Only two lan-

guages are available in the meter at one time

Use the Up / Down scroll keys to change between languages. When finished,

press Enter to end the process and store the setting.

Language

LANGUAGE SETTING

Language: English

The meter will automatically turn off after 10 minutes of non use (no torque read-

ings or no presses of the key pad buttons).

This function is used to turn off the sleep mode for users that do not want the

meter to go to sleep.

Use the Up / Down scroll keys to change between sleep mode On / Off. When

finished, press Enter to end the process and store the setting.

Caution: The meter will have significantly less operational life if Sleep Mode is

turned off.

Sleep

SLEEP MODE SETTING

Auto Sleep: On

TOLERANCE SETTING

Low: 10.000

High: 14.00

Units: Lbf.in

The Tolerance parameters control the Go and No-Go multicolored Green / Red

LED and In Tolerance and Out of Tolerance indication on the meter screen. The

user sets a lower and upper torque threshold to get a visual warning signal when

these limits are reached or breached during operation.

When you first enter the Tolerance Setting screen Low Tolerance will be in

reverse video. When this is true you can scroll between Low and High tolerance

using the Scroll Up / Down keys.

To set the Tolerance press Enter and the value will change to normal video and

the cursor with be on the last digit. Use the Scroll Up / Down keys to increase

or decrease digits and scroll left to move to the next digit. When done with Low

Tolerance press Enter and the Low Tolerance will appear in reverse video. Use

Scroll down to move to High Tolerance and then press enter to edit the value.

After completion press the Menu key.

Tolerance

Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: (408) 292-2214 Fax: (408) 292-2733

www.mountztorque.com

Inhaltsverzeichnis

Andere Mountz Prüfgeräte Handbücher

Mountz

Mountz TCA Gebrauchs- und Pflegehandbuch

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung