MOVETEC LC Series Benutzerhandbuch

Instruction LTC 11_4

- 1 -

Installation and operating

instruction

LC/LTC Series

Laing Innotech GmbH + Co. KG Althuette Germany Instruction LTC 11_5

- 2 -

Table of contents

Table of contents ..................................................................................................- 2 -

1 The LTC table controller....................................................................................- 5 -

1.1 Application.....................................................................................................- 5 -

1.2 For whom this document is prepared for........................................................- 5 -

1.3 Preconditions for the use of this document....................................................- 5 -

1.4 Safety instructions.........................................................................................- 5 -

1.4.1 Indications for all Laing Table Controllers and all accessories (products).............- 6 -

1.4.2 Indications for the operation of height adjustable tables .......................................- 6 -

1.5 Design of the table controllers.......................................................................- 6 -

1.6 Specifications................................................................................................- 7 -

1.6.1 Controller for mains connection LTC .....................................................................- 7 -

1.6.2 Controller for DC-operation LTCD .........................................................................- 7 -

1.6.3 Controller for battery-operation LTCB....................................................................- 8 -

1.7 Environmental conditions ..............................................................................- 8 -

1.8 Dimensions controller for mains connection LTC...........................................- 9 -

1.8.1 Controller without OptoSense................................................................................- 9 -

1.8.2 Controller with OptoSense...................................................................................- 10 -

1.9 Dimensions controller for DC-operation LTCD.............................................- 10 -

1.10 Dimensions controller for battery-operation LTCB .....................................- 11 -

1.11 Options......................................................................................................- 11 -

1.12 Delivery contents.......................................................................................- 11 -

2 Installation of the controllers..........................................................................- 12 -

2.1 Controllers without OptoSense....................................................................- 12 -

2.2 Battery controller LTCB...............................................................................- 12 -

2.3 Controller with OptoSense...........................................................................- 13 -

2.4 Controller with GyroSense / GraviSense .....................................................- 14 -

2.5 Installation of the control panels..................................................................- 14 -

2.5.1 Rectangular control panels ..................................................................................- 14 -

2.5.2 Oval control panels ..............................................................................................- 15 -

2.6 Electrical connection....................................................................................- 16 -

2.6.1 Connectable Motors.............................................................................................- 17 -

2.6.2 Pin assignment controller.....................................................................................- 17 -

2.7 Connection of the motors ............................................................................- 18 -

2.8 Connection of the control panels and other control options..........................- 18 -

2.8.1 Control panels with cable.....................................................................................- 18 -

2.8.2 Connection of two control panels.........................................................................- 18 -

2.8.3 Connection of up to 11 control panels .................................................................- 19 -

2.8.4 OptoSense ...........................................................................................................- 19 -

2.9 Wireless control panel LM4RW ...................................................................- 19 -

2.9.1 Connection...........................................................................................................- 20 -

2.9.2 Mounting the wireless control panel.....................................................................- 20 -

2.9.3 Pairing the control panel and the controller .........................................................- 20 -

2.9.4 Battery change.....................................................................................................- 21 -

2.10 Mains connection LTC...............................................................................- 21 -

2.11 Connection LTCD......................................................................................- 22 -

2.12 Connection, battery change and charging of the LTCB..............................- 22 -

2.13 Preconditions for the start of operation of the controller.............................- 23 -

3 Start of operation .............................................................................................- 24 -

3.1 Current based collision detection.................................................................- 24 -

3.2 GyroSense based collision detection...........................................................- 24 -

3.3 GraviSense based collision detection..........................................................- 25 -

3.4 Adjusting the sensitivity level by the user.....................................................- 25 -

3.5 Reference run..............................................................................................- 26 -

3.6 Determining the stroke by the reference run................................................- 27 -

Instruction LTC 11_4 Laing Innotech GmbH + Co. KG Althuette Germany

- 3 -

3.7 Safety zone .................................................................................................- 27 -

3.8 Safety Input .................................................................................................- 28 -

3.9 Automatic motor recognition........................................................................- 29 -

4 Controlling through control panels.................................................................- 30 -

4.1 All Control panels ........................................................................................- 30 -

4.2 Control panels with memory keys................................................................- 30 -

4.3 Recall memory position with 2-Button control panel without height indication - 30

4.4 Control panels with height indication............................................................- 31 -

4.5 Controlling the controller by OptoSense.......................................................- 31 -

4.6 Configuration of the controller through the “LM” control panels (control panels

without height indication)...................................................................................- 32 -

4.6.1 Store memory positions with “LM” control panels ............................................... - 32 -

4.6.2 User height limit adjustment by “LM” control panels ........................................... - 32 -

4.6.3 Minimum stroke ................................................................................................... - 33 -

4.6.4 Changing the sensitivity of the collision detection by “LM” control panels .......... - 33 -

4.6.5 Initiating a reference run by “LM” control panels ................................................. - 34 -

4.7 Configuration of the controller through the “LD” control panels (with height

indication)..........................................................................................................- 35 -

4.7.1 Operation of “LD” control panels without memory keys ...................................... - 35 -

4.7.2 Storing memory positions by the “LD” control panels ......................................... - 35 -

4.7.3 Activating button mode of the memory keys by the “LD” control panels ............. - 35 -

4.7.4 User height limit adjustment by the “LD” control panels...................................... - 36 -

4.7.5 Stroke limitation adjustment by “LD” control panels ............................................ - 37 -

4.7.6 Minimum stroke ................................................................................................... - 38 -

4.7.7 Changing the sensitivity of the collision detection by the “LD” control panels .... - 39 -

4.7.8 Initiating a reference run by the “LD” control panels ........................................... - 39 -

4.7.9 Adjusting direction of the reference run............................................................... - 40 -

4.7.10 Changing height indication from centimeter to inch by the “LD” control panels - 40 -

4.7.11 Entering the info menu by the “LD” control panel.............................................. - 41 -

4.7.12 Shifting the height indication by the “LD” control panels ................................... - 41 -

4.7.13 Defining the rounding for height indication by “LD” control panels ................... - 41 -

4.7.14 Resetting user settings by the “LD” control panel ............................................. - 42 -

4.7.15 Activating the BLE module ................................................................................ - 42 -

4.7.16 Resetting the controller name ........................................................................... - 43 -

4.7.17 Activating the pairing mode............................................................................... - 43 -

4.7.18 Deleting connections to wireless control panels ............................................... - 44 -

4.7.19 Resetting the private mode for the app............................................................. - 44 -

4.7.20 Entering the option menu by the “LD” control panel.......................................... - 45 -

4.7.21 Resetting the number of connected motors ...................................................... - 46 -

4.7.22 Resetting the Safety Adapter ............................................................................ - 46 -

4.7.23 Setting the starting point for the safety zone..................................................... - 47 -

4.7.24 Displaying the last error by the “LD” control panel ............................................ - 48 -

4.7.25 Synchronization of 2 controllers by the ”LD” control panel................................ - 48 -

5 Synchronization of up to 6 controllers by HUB..............................................- 49 -

5.1 Port designation...........................................................................................- 50 -

5.2 Configuration...............................................................................................- 50 -

5.2.1 Connecting the controllers to the HUB................................................................ - 51 -

5.2.2 Remaining ports .................................................................................................. - 51 -

5.3 HUB startup.................................................................................................- 51 -

5.4 Operation.....................................................................................................- 52 -

5.5 Connecting a PC to the HUB.......................................................................- 52 -

5.6 Exchanging a controller ...............................................................................- 52 -

5.7 HUB Menu handling.....................................................................................- 53 -

5.7.1 Restarting the HUB by the „LD“ control panel ..................................................... - 53 -

5.7.2 Deleting the configurations stored in the HUB by the “LD” control panel............ - 53 -

5.7.3 Adjusting the number of controllers connected to the HUB by the “LD” control panel -

54 -

Laing Innotech GmbH + Co. KG Althuette Germany Instruction LTC 11_5

- 4 -

5.7.4 Choosing the HUB port for transferring the configuration by the “LD” control panel ..-

54 -

5.7.5 Displaying the last error in HUB mode by the “LD” control panel ........................- 55 -

6 BLE Option.......................................................................................................- 55 -

7 WiFi Option.......................................................................................................- 56 -

8 Status and failure modes indicated by the LED.............................................- 56 -

8.1 Menu codes for control panels without height indication “LM”......................- 57 -

8.2 Menu codes indicated by the “LD” control panels ........................................- 58 -

8.3 Failure codes indicated by the control panels..............................................- 63 -

9 Sound signals...................................................................................................- 72 -

10 Directives and approvals...............................................................................- 73 -

10.1 Directives followed.....................................................................................- 73 -

10.2 Approvals for European Controllers (230V versions).................................- 73 -

10.3 Approvals for USA and Canada (115V versions).......................................- 73 -

Instruction LTC 11_4 Laing Innotech GmbH + Co. KG Althuette Germany

- 5 -

1 The LTC table controller

Thank you for choosing our controller. The well-shaped controllers can be easily

mounted below a tabletop or into a crossbar of a height adjustable table. A

variety of control panels and control modes enable the user to find the optimum

solution for many applications.

This instruction describes how to install and how to operate the controller.

1.1 Application

The LTC Controller series is designed and can be exclusively used to control

motors for the height adjustment of tables. It has to be verified that the

performance parameters of the motors and the connections of the motors fit the

parameters and connections of the controller.

Attention: If used for other applications neither the function nor the safety can be

ensured! Therefore, such use is not permitted, and warranty will be voided if used

in applications outside the table height adjustment area.

1.2 For whom this document is prepared for

This document is an installation and operation instruction for the LTC series

Laing Table Controllers and its accessories. The document is dedicated to

manufacturers of height adjustable table frames and tables.

This document is not intended for end users!

1.3 Preconditions for the use of this document

This document describes installation and operation of the controllers. It is

assumed, that the controller has already been configured for the application in

which it is intended to be used. All parameters for the table the controller is

intended to be mounted to, have to be programmed before the actual installation.

Do not install the system before programming!

1.4 Safety instructions

Attention: There are no parts inside the controller which are serviceable or

repairable by the user! Do not open the controller. If opened, the warranty will be

void.

Laing Innotech GmbH + Co. KG Althuette Germany Instruction LTC 11_5

- 6 -

1.4.1 Indications for all Laing Table Controllers and all accessories (products)

Before any work is done with the products, read the instruction manual and follow

the instructions!

Attention: The products may only be used as intended. Danger may occur if

products are used in another way or in other applications than the intended ones.

•The installation may only be performed by qualified personnel with the

required knowledge and the required capabilities!

•When making electrical connections, applicable electrical codes must be

observed in respect to the way the connection is made, as well as who is

authorized to perform such connection!

•Electrical installations can only be made by authorized personnel!

•Operation outside the specified operation limits is not allowed!

•Operation outside the specified environmental conditions is not allowed!

1.4.2 Indications for the operation of height adjustable tables

•Operation of a height adjustable table is only allowed after being instructed

by a person familiar with the product or after thorough study of the

instruction manual.

•Children are not allowed to play with the table.

•When operated, no persons are allowed on the tabletop

•Danger of collision! The table must be placed in a way that it can operate

without colliding with any objects like drawers or windowsills!

•Danger of injury by squeezing! The table must be placed and operated

in a way that no person can be squeezed between the tabletop or other

parts of the table and other objects in the vicinity of the table.

•Children under the age of 8 and persons with mental or physical

disabilities are only allowed to operate the table if they have been

sufficiently familiarized with the operation of the table and if it is certain,

that they will not be overburdened with the operation of the table.

•Use of the table is only permitted in closed buildings where it can be

insured the no water or high humidity can get to the electrical parts.

•The controllers are manufactured and tested using the utmost care.

Should there be a problem, please contact our service department.

1.5 Design of the table controllers

•Highly efficient switching power supply drives one, two, three or four motor

channels (controllers for mains connection)

•The motor channels are controlled by a powerful processor

Instruction LTC 11_4 Laing Innotech GmbH + Co. KG Althuette Germany

- 7 -

•The controller can be configured to a wide variety of applications by an

easy-to-use configuration software

•The aluminum housing provides superior heat dissipation which is why in

most applications the cool down time is not determined by the controller

but by the motors connected to the controller

•Optional port for the OptoSense Sensor

•Optional integrated collision detection

•Status indication by LED or by control panels with height indication

•A bus connection is provided for the following uses

oConnection of the control panels

oConfiguration of the controller by PC

oFirmware update

oSynchronization of up to six controllers

•An internal extension port is provided for the optional placement of a WiFi

or BLE module. The BLE module enables the operation by wireless control

panels

1.6 Specifications

Type LTC 302 LTC 383 LTC 384

Max. output power 300 W 380 W 380 W

Output voltage 24 V 24 V 24 V

Output current total 15 A 19 A 19 A

Motor channels 2 3 4

Max. current per channel 9 A 9 A 9 A

Synchronization by HUB or LD by HUB or LD by HUB or LD

1.6.1 Controller for mains connection LTC

Input voltage 230 V 50/60 Hz 230 V 50/60 Hz 230 V 50/60 Hz

Input current 2,9 A 3,5 A 3,5 A

Frequency 50-60 Hz 50-60 Hz 50-60 Hz

Standby power 250 mW 250 mW 250 mW

1.6.2 Controller for DC-operation LTCD

Input voltage 10 V - 36 V 10 V -3 6 V 10 V - 36 V

Laing Innotech GmbH + Co. KG Althuette Germany Instruction LTC 11_5

- 8 -

Input current 15 A 22 A 30 A

Frequency DC DC DC

Standby power 12 V 80 mW 100 mW 130 mW

Standby power 24 V 180 mW 220 mW 250 mW

1.6.3 Controller for battery-operation LTCB

Battery voltage 32 V 32 V 32 V

Input current 13 A 13 A 13 A

Frequency DC DC DC

Standby power -

battery and controller 5 mW 5 mW 5 mW

1.7 Environmental conditions

The environmental conditions are valid for all controllers and accessories

Environmental temperature for storage and transport: min: -20°C to max: 60°C

min: -4°F to max: 140°F

Environmental temperature for operation: min: 5°C to max: 45°C

min: 41°F to max: 113°F

Max. humidity for storage, transport and operation: 95% non-condensing

Instruction LTC 11_4 Laing Innotech GmbH + Co. KG Althuette Germany

- 9 -

1.8 Dimensions controller for mains connection LTC

1.8.1 Controller without OptoSense

Laing Innotech GmbH + Co. KG Althuette Germany Instruction LTC 11_5

- 10 -

1.8.2 Controller with OptoSense

1.9 Dimensions controller for DC-operation LTCD

For the differing measurements of the OptoSense option see “controller for mains

connection”

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MOVETEC Controller Handbücher

MOVETEC

MOVETEC LTC Series Benutzerhandbuch

MOVETEC

MOVETEC MCP-TDH6 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung