Moxa Technologies MD-200 Series Bedienungsanleitung

P/N: 1802002260012

*1802002260012*

MD-200 Series

Quick Installation Guide

Version 2.1, January 2021

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

The MD-200 marine display series is designed for durably reliable service

as an ECDIS display component. The MD-200 series offers full range

dimming and optional optical bonding, making it well-suited not only for

ECDIS applications, but also for a variety of other bridge applications.

The MD-200 series features both AC and DC power inputs, and can be

conveniently installed on any bridge, without the need for extra

hardware.

Moxa’s marine displays are compliant with the most important industrial

marine standards, including IEC 60945, DNV, and IACS-E10, giving

strong assurance of their suitability for marine applications.

The following lists the models in the MD-200 series:

•MD-226X: 26-inch display with 16:10 aspect ratio.

•MD-224X/MD-224Z: 24-inch display with 16:9 aspect ratio.

•MD-219X/MD-219Z: 19-inch display with 5:4 aspect ratio.

Package Checklist

Before installing the MD-200 series, verify that the package contains the

following items:

•MD-200 series display

•VGA cable

•DVI-D cable

•2-pin terminal block x 1

•5-pin terminal block x 2

•Quick installation guide (printed)

•Warranty card

NOTE: Please notify your sales representative if any of the above items

are missing or damaged.

Hardware Installation

Appearance

- 3 -

MD-226/224

MD-219

SavvyTouch Display Control Buttons

The following table describes the SavvyTouch display controls on the

front surface of the MD-200 series. These intelligent controls will light up

with a simple wave of your hand over the area of the screen where they

are located.

Name

Display

Color

Control Function/Color Legend

Menu/

Power

Green

Display is powered on and functioning

normally. Touch the button to show the

OSD settings menu

Red

No input signal detected. Display standby

Off

Power is down and the display is off

Brightness

White

+: To increase brightness of panel

-: To decrease brightness of panel

Info

Off AC/DC power is functioning normally

Display

mode

White Switch between DAY/DUSK/NIGHT

brightness modes

Off

Panel brightness out of default range

Installing the MD-200 Series

Desktop

The MD-200 series comes with optional brackets that allow you to install

the display on a horizontal surface, such as a desktop. Three round

screws are required for each bracket. See the figure for detailed screw

specifications and their torque values.

Place your MD-200 series display on a clean, flat, well-ventilated desktop.

To protect the computer from overheating, leave some ventilation space

between the MD-200 series and other equipment.

Do NOT place equipment or objects on the panel, as this might damage

internal components.

- 4 -

Panel Mounting

The MD-200 series comes with 14 optional clamp mounts for installation

on a wall (where space has been cut out to accommodate the rest of the

hardware) or into computing stations where a flush mount is desired.

The maximum thickness of the surface to which the computer can

be clamped is 11 mm. For a secure mounting, all 14 clamps must be

used.

The clamp arms are fastened into slots on all four sides of the MD-200

series. Use the short M4 SUS screws to fasten the clamp arms to the

MD-200 series mounting slots, as shown in the following magnified inset

in the diagram. Next, use the clamps to fasten the MD-200 series to its

mounting point; please note the torque value as shown in the figure.

- 5 -

VESA Mounting

The MD-200 series also comes with an optional VESA mounting kit. Six

flat screws and four round screws are required to fasten the VESA

mounting bracket. See the following figure for detailed screw

specifications and torque values.

An additional four screws (not included in the kit) are required to mount

the display on a VESA rack. For this purpose, use M6 screws that are

between 10 and 12 mm in length.

Connector Description

Extending the Display

The MD-200 series comes with both standard VGA and DVI-D interfaces

on the bottom panel. It automatically detects whether the input video

source is from the VGA or DVI-D interface.

Configuring the Display via the Serial Port

The MD-200 series has two serial ports. The RS-232 port uses a DB9

connector, and the RS-422/485 port uses a terminal block connector.

Either serial port can be used to modify the display parameters using

UART commands. For information on serial port configuration, see the

MD-200 Series Hardware Manual.

The pin assignments for the ports are shown in the following table:

RS-232

DCD

RxD

TxD

DTR

GND

DSR

RTS

CTS

RS-422/485 (Terminal Block) Pinouts

RS-422

RS-485

(4-wire)

RS-485

(2-wire)

RxDB(+)

–

RxDA(-)

–

TxDB(+)

DataB(+)

TxDA(-)

DataA(-)

GND

- 6 -

Powering on/off the MD-200 Series

To power on the MD-200 series, connect the unit to an AC power source,

a DC power source, or both. Touch the MENU button for 1 second to turn

on the display. Touch the MENU button for 4 seconds to turn off the

display.

Grounding the MD-200 Series

Proper grounding and wire routing help to limit the effects of noise from

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting the power

source.

For detailed configuration of the MD-200 Series, refer to the MD-200

Series Hardware Manual.

Andere Handbücher für MD-200 Series

Inhaltsverzeichnis

Andere Moxa Technologies Monitor Handbücher

Moxa Technologies

Moxa Technologies MD-124 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MD-119 Bedienungsanleitung

Moxa Technologies

Moxa Technologies MD-224 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MD-219 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MD-200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MD-119 Bedienungsanleitung

Moxa Technologies

Moxa Technologies MD-215 Series Gebrauchsanweisung

Moxa Technologies

Moxa Technologies MD-219 Series Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung