Moxa Technologies DR-45 Series Bedienungsanleitung

DR-45 Series

Quick Installation Guide

Edition 1.0, November 2015

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Dimensions

Terminal Pin No. Assignments

PIN No.

Assignment

1, 2

AC Input

4, 5

DC Output V-

6, 7

DC Output V+

LED lit for DC OK

+V ADJ

Mounting Instructions

Mounting: Mount only as shown in figure, with input terminals facing

upwards to allow sufficient cooling.

Admissible DIN rails: TS35/7.5 or TS35/15.

To attach the DR-45 to the rail:

1. Rotate the DR-45 backwards, as shown in the figure.

2. Fit the top of the DR-45 over the top hat rail.

3. Slide the DR-45 downwards until it hits the stop.

4. Push the bottom of the DR-45 forward until it snaps into place.

5. Move the DR-45 back and forth to make sure it is locked in place.

- 3 -

Installation

1. To prevent the unit from overheating, always allow sufficient

clearance around the unit for proper ventilation: 5 mm left and right,

40 mm above, and 20 mm below. You should also keep a 10 to 15 cm

clearance from adjacent devices that act as a heat source.

2. The appropriate mounting orientation is vertical, with input terminals

on the right and output on the left of the DR-45. Other mounting

orientations, such as upside down, horizontal, or table-top, are not

allowed.

3. Use copper wire only; the recommended wiring is shown below.

AWG

Rated Current

(Amps)

6 6-10 13-16 16-25 25-32

Lead cross-section

(mm

)

0.75 1.00 1.5 2.5 4

Note:

1. When 5 or more wires are connected to the unit, the current

carried by each wire could be 20% less than the current listed

above.

2. The maximum allowable cross-sectional area of wires

connected

to the DR-45’s terminals is 12AWG/2.5 mm

Make sure that all strands of each wire are properly inserted into the

terminal connection, and that the screw terminals are securely fixed

to prevent poor contact. If the power supply has multiple output

terminals, make sure each contact is connected to wires to prevent

stress on a single contact from too much current.

4. Use wire that can withstand temperatures of at least 80°C, such as

UL1007.

5. Suggested fuses and the maximum number of the PSUs that can be

connected to a circuit breaker at 230 V are shown as below:

Model Fuse

Circuit breakers

C16

D16

DR-45

T2.5A/L250V

6. The recommended wire strapping length is 5 mm (0.197 inch).

7. Use a slotted type 4 mm screwdriver.

8. Use the following torque settings for terminals:

Model

I/P

O/P

DR-45

5 kgf-cm (4.4 in-lb)

- 4 -

Important Safety Precautions

Before working with a power supply, be sure to read and understand

these instructions carefully and completely. You should also follow any

notes or instructions on the unit itself.

1. Risk of electrical shock and energy Hazard: If the device fails, it

must be examined by a qualified technician. Do not remove the

DIN-rail power supply casing yourself.

2. Risk of electric arcs and electric shock (danger to life): Do not

connect the primary and secondary sides together, since doing so

could result in life threatening shocks.

3. Risk of burn hazard: Do not touch the unit while it is in operation or

shortly after it has been disconnected.

4. Risk of fire and short circuits: Openings on the product should be

protected from foreign objects and dripping liquids.

5. Pollution level: Only install the unit in a pollution level degree 2

environment.

6. Humidity warning: Do not install the unit in locations with high

humidity, or near water.

7. The maximum operating temperature for the DR-45 is:

Model

Temperature

DR-45

50°C

8. The FG ( ) must be connected to PE (Protective Earth).

9. Output current and output wattage must not exceed the rated values

in the product’s specifications.

10. Before doing any installation, maintenance, or modification work,

disconnect the system from the power source. Make sure that

inadvertent connection in circuit will be impossible!

11. For continued protection against risk of fire, replace only with fuses of

the same type and rating.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Stromversorgung Handbücher

Moxa Technologies

Moxa Technologies DR-120-24 Bedienungsanleitung

Moxa Technologies

Moxa Technologies DR-75 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MDR Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies DR-120 Series Handbuch

Moxa Technologies

Moxa Technologies DRP-240 Bedienungsanleitung

Moxa Technologies

Moxa Technologies V2416A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies DRP-240 Series Handbuch

Moxa Technologies

Moxa Technologies DR-75 Series Handbuch

Moxa Technologies

Moxa Technologies HDR-60-24 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies SDR-480P Series Handbuch

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung