Moxa Technologies EtherDevice EDS-728 Series Handbuch
Moxa EtherDevice Switch
EDS-728/828 Hardware Installation Guide
First Edition, January 2008
Moxa Inc.
Tel: +886-2-8919-1230
Fax: +886-2-8919-1231
www.moxa.com
Moxa Technical support.
Worldwide: support@moxa.com
The Americas: support@usa.moxa.com
P/N: 1802008280010
1
Panel Layout of EDS-728/828 Series
COUPLER
MODE
RING
PORT COUPLER
PORT
FDX/HDX
STAT
PWR1 FAULT
MASTER
PWR2
LNK/ACT
SPEED
IM-4MSC
TX
RX
34
TX
RX
12
PWR
P3
P1
P4
P2
IM-4MST
TX
RX
34
TX
RX
12
PWR
P3
P1
P4
P2
34
IM-4TX
12
PWR
P3
P1
P4
P2
RS-232
Console
T.RING
1M-2 GTX
11
22
P1 P1
P2 P2
1M-2 GSFP
1
2
5
6
8
7
9
10
11
3
4
12
RELAY1
PWR1
PWR2
V1 V2 INPUT: 24VDC
DI1
I1
I2
V2+
V2-
V1+
V1-
DI2
RELAY2
2
13 1314 1515
13
16
1. System status LEDs
2. Push-button switch to select mode for Interface Module
3. Interface Module mode LEDs
4. Fast Ethernet Interface Module port LEDs
5. Terminal block for 2 power inputs, 2 DIs, and 2 DOs
6. Sticker showing pin contacts
7. Serial console port
8. Screw to attach Fast Ethernet Interface Module
9. Gigabit Ethernet Module LEDs
10. Two cartridge receptors for Gigabit Ethernet Interface Modules
11. Fast Ethernet Interface Modules
12. Sockets for Fast Ethernet Interface Modules
13. DIN-Rail braces
14. Ribs for radiating heat
15. Screw holes for wall mounting kit
16. Grounding screw
3
Mounting Dimensions (unit = mm)
381.70
3085.00
142.47
Front View
EtherDevice Switch
80.6 201.2
362.40
401.00
Rear View
128.00
142.47
140.00
Side View
Gigabit Ethernet Interface Modules
Front View Side View
101.1
65.9
24
Fast Ethernet Interface Modules
40
127.8
127.8
100
Side View
Front View
EDS-728/828
4
DIN-Rail Mounting
The DIN-Rail attachment plates are permanently fixed to the back panel of the
EDS-728/828. Do not attempt to remove the attachment plates, since doing so
could damage the product.
To Install:
Lock the brace by pressing the clips and then insert the top of the DIN-Rail
into the notches at the bottom of the top array of heat radiating ribs. Press the
EDS until the brace snaps into place.
To Release:
Use a flat-blade screw driver as a lever to force the braces downwards, and
then pull the EDS-728/828 out away from the DIN-Rail.
Wall Mounting (optional)
For some applications, you will find it convenient to mount the EDS-728/828
on the wall, as illustrated below.
STEP 1: Remove the aluminum DIN-Rail attachment plate from the
EDS-728/828’s rear panel, and then attach the wall mounting plates, as shown
in the diagram.
5
STEP 2:
Mounting the EDS-728/828 on the wall requires 4 screws to
ensure that the switch does not come loose from the wall.
Use the switch, with wall mounting plates attached, as a
guide to mark the correct locations of the 4 screws. The
heads of the screws should be less than 6.0 mm in diameter,
and the shafts should be less than 3.5 mm in diameter, as
shown in the figure at the right.
6.0 mm
3.5 mm
NOTE Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw into one of
the keyhole-shaped apertures of the Wall Mounting Plates.
Do not screw the screws in all the way—leave about 2 mm to allow room for
sliding the wall mount panel between the wall and the screws.
STEP 3: Once the screws are fixed in the wall, insert the four screw heads
through the large parts of the keyhole-shaped apertures, and then slide Moxa
EDS downwards, as indicated. Tighten the four screws for added stability.
EtherDevice Switch
EtherDevice Switch
EDS-728/828
EDS-728/828
Uninstalling IM-2G Modules
As shown in the figure below, use a flat-blade screw driver as a lever, and pull
or push it to force the IM-2G module outwards. Then pull the module out away
from the EDS-728/828.
6
Wiring Requirements
WARNING
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa EDS-728/828.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
You should also pay attention to the following guidelines:
yUse separate paths to route wiring for power and devices. If power wiring
and device wiring paths must cross, make sure the wires are perpendicular
at the intersection point.
yNOTE: Do not run signal or communications wiring and power wiring in
the same wire conduit. To avoid interference, wires with different signal
characteristics should be routed separately.
yYou can use the type of signal transmitted through a wire to determine
which wires should be kept separate. The rule of thumb is that wiring that
shares similar electrical characteristics can be bundled together.
yKeep input wiring and output wiring separated.
yIt is strongly advised that you label wiring to all devices in the system when
necessary.
Grounding Moxa EtherDevice Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw, on the side panel of the EDS-728/828, to the grounding surface
prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well-grounded
mounting surface, such as a metal panel.
Wiring the Relay Contact
In this section, we explain the meaning of the two contacts used to connect the
alarm contact.
The EDS-728/828 has two sets of relay output—relay 1 and relay 2. Each relay
contact consists of the two contacts of the terminal block on the
EDS-728/828’s top panel. Refer to the next section for detailed instructions on
how to connect the wires to the terminal block connector, and how to attach the
terminal block connector to the terminal block receptor.
7
RELAY1 RELAY2 PWR1 PWR2
V2+
V2-V1+
V1-
DI1
I1I2
DI2
Top View
Front View
FAULT: The two sets of relay
contacts of the 6-pin terminal block
connector are used to detect
user-configured events. The two
wires attached to the Fault contacts
form an open circuit when a
user-configured event is triggered.
If a user-configured event does not
occur, the Fault circuit will be
closed.
Wiring the Redundant Power Inputs
The EDS-728/828 has two sets of power input—power input 1 and power input
2. The top two contacts and the bottom two contacts of the 6-pin terminal block
connector on EDS’s top panel are used for EDS’s two digital inputs.
RELAY1 RELAY2 PWR1 PWR2
V2+
V2-V1+
V1-
DI1
I1I2
DI2
Top View
Front View
STEP 1: Insert the
negative/positive DC wires into the
V-/V+ terminals.
STEP 2: To keep the DC wires
from pulling loose, use a small
flat-blade screwdriver to tighten
the wire-clamp screws on the front
of the terminal block connector.
STEP 3: Insert the plastic terminal
block connector prongs into the
terminal block receptor, which is
located on the EDS-728/828’s top
panel.
Wiring the Digital Inputs
The EDS-728/828 has two sets of digital input—DI 1 and DI 2. Each DI
comprises two contacts of the 6-pin terminal block connector on EDS’s top
panel. The terminal block is also used for EDS’s two DC inputs. Top and front
views of one of the terminal block connectors are shown here.
RELAY1 RELAY2 PWR1 PWR2
V2+
V2-V1+
V1-
DI1
I1I2
DI2
Top View
Front View
STEP 1: Insert the negative
(ground)/ positive DI wires into the
┴/I1 terminals.
STEP 2: To keep the DI wires
from pulling loose, use a small
flat-blade screwdriver to tighten
the wire-clamp screws on the front
of the terminal block connector.
STEP 3: Insert the plastic terminal
block connector prongs into the
terminal block receptor, which is
located on the EDS-728/828’s top
panel.
8
Communication Connections
The pinout and cable wiring diagrams in this section show how the ports on the
EDS-728/828 connect to other devices:
Pinouts are diagrams that indicate the type of signal passing through each of
the port’s pins.
NOTE 1. The pin numbers for male DB9 and DB25 connectors, and hole
numbers for female DB9 and DB25 connectors are labeled on the
connector. However, the numbers are typically quite small, so you
may need to use a magnifying glass to see the numbers clearly.
2. The pin numbers for both 8-pin and 10-pin RJ45 connectors (and
ports) are typically not labeled on the connector (or port). Refer to
the Pinout diagram below to see how RJ45 pins are numbered.
RS-232 Connection
The EDS-728/828 has one RS-232 (10-pin RJ45) console port, located on the
front panel. Use either an RJ45-to-DB9 or RJ45-to-DB25 cable to connect the
Moxa EDS-728/828’s console port to your PC’s COM port. You may then use
a console terminal program to access the Moxa EDS-728/828’s console
configuration utility.
10-pin RJ45 Console Pinouts
10-Pin Description
1 ------
2 DSR
3 ------
4 GND
5 TxD
6 RxD
7 GND
8 ------
9 DTR
10 ------
110
10/100BaseT(X) Ethernet Port Connection
Below we show pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports.
MDI Port Pinouts MDI-X Port Pinouts 8-pin RJ45
Pin Signal Pin Signal
1 Tx+ 1 Rx+
2 Tx- 2 Rx-
3 Rx+ 3 Tx+
6 Rx- 6 Tx-
1000BaseT Ethernet Port Connection
1000BaseT data is transmitted on differential TRD+/- signal pairs over copper
wires.
1
8
9
MDI/MDI-X Port Pinouts
Pin Signal
1 TRD(0)+
2 TRD(0)-
3 TRD(1)+
4 TRD(2)+
5 TRD(2)-
6 TRD(1)-
7 TRD(3)+
8 TRD(3)-
1
8
100/1000Base Fiber Port Connection
The concept behind the duplex port and cable is quite straightforward. Suppose
you are connecting devices I and II. Contrary to electrical signals, optical
signals do not require a circuit in order to transmit data. Consequently, one of
the optical lines is used to transmit data from device I to device II, and the
other optical line is used to transmit data from device II to device I, for
full-duplex transmission.
All you need to remember is to connect the Tx (transmit) port of device I to the
Rx (receive) port of device II, and the Rx (receive) port of device I to the Tx
(transmit) port of device II. If you make your own cable, we suggest labeling
the two sides of the same line with the same letter (A-to-A and B-to-B or
A1-to-A2 and B1-to-B2).
ATTENTION
This is a Class 1 Laser/LED product. To avoid causing serious
damage to your eyes, do not stare directly into the Laser Beam.
LED Indicators
LED Color State Description
System LEDs
On System has passed self-diagnosis test on
boot-up and is ready to run.
GREEN
Blinking System is undergoing the self-diagnosis
test.
STAT
RED On System failed self-diagnosis on boot-up.
On Power is being supplied to the main
module’s power input PWR1.
PWR1 AMBER
Off Power is not being supplied to the main
module’s power input PWR1.
On Power is being supplied to the main
module’s power input PWR2.
PWR2 AMBER
Off Power is not being supplied to the main
module’s power input PWR2.
On
The corresponding PORT alarm is
enabled and a user-configured event has
been triggered.
FAULT RED
Off
The corresponding PORT alarm is
enabled and a user-configured event has
not been triggered, or the corresponding
PORT alarm is disabled.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Moxa Technologies Schalten Handbücher
Moxa Technologies
Moxa Technologies EDS-G205-1GTXSFP-T Handbuch
Moxa Technologies
Moxa Technologies MDS-G4000-4XGS Series Bedienungsanleitung
Moxa Technologies
Moxa Technologies EtherDevice EDS-510A Series Bedienungsanleitung
Moxa Technologies
Moxa Technologies PT-G7728 Bedienungsanleitung
Moxa Technologies
Moxa Technologies PT-7710 Series Handbuch
Moxa Technologies
Moxa Technologies PT-7728 Series Bedienungsanleitung
Moxa Technologies
Moxa Technologies TN-5510A Series Bedienungsanleitung
Moxa Technologies
Moxa Technologies ToughNet TN-4500A Series Bedienungsanleitung
Moxa Technologies
Moxa Technologies IKS-6728 Series Handbuch
Moxa Technologies
Moxa Technologies EtherDevice EDS-205A series Montageanleitung
Moxa Technologies
Moxa Technologies EDS-G509 Series Bedienungsanleitung
Moxa Technologies
Moxa Technologies PT-510 Series Handbuch
Moxa Technologies
Moxa Technologies ToughNet TN-5510A-2GLSX-ODC Handbuch
Moxa Technologies
Moxa Technologies EDS-P308 Series Handbuch
Moxa Technologies
Moxa Technologies ICS-G7526A Series Bedienungsanleitung
Moxa Technologies
Moxa Technologies EDS-G4014 Series Bedienungsanleitung
Moxa Technologies
Moxa Technologies EtherDevice EDS-4012 Series Bedienungsanleitung
Moxa Technologies
Moxa Technologies TN-5500A Series Bedienungsanleitung
Moxa Technologies
Moxa Technologies NPORT 6610 Bedienungsanleitung
Moxa Technologies
Moxa Technologies EtherDevice EDS-P510 Series Handbuch
Moxa Technologies
Moxa Technologies IESH-MB205G-C2E-R Series Bedienungsanleitung
Moxa Technologies
Moxa Technologies EtherDevice EDS-2016-ML Series Bedienungsanleitung
Moxa Technologies
Moxa Technologies EtherDevice EDS-510A-3GT Handbuch
Moxa Technologies
Moxa Technologies EDS-508A Series Bedienungsanleitung
