Moxa Technologies PT-G7728 Bedienungsanleitung

P/N: 1802077280410

*1802077280410*

PT-G7728/G7828

Quick Installation Guide

Edition 1.0, December 2017

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



www.ipc2u.ru

www.ipc2u.com

www.moxa.pro

- 2 -

Package Checklist

Moxa’s PT-G7728/G7828 industrial rackmount switch is shipped with the

following items. If any of these items are missing or damaged, please

contact your customer service representative for assistance.

•1 PT-G7728 or G7828 switch

•USB cable (Type A male to Micro USB type B)

•2 protective caps for unused ports, 3 protective caps for unused USB

ports

•2 rackmount ears

•Quick installation guide (printed)

•Substance Disclosure Table

•Product Certificate of Quality Inspection (Simplified Chinese)

•Product Notices (Simplified Chinese)

•Warranty card

NOTE

You can find information and software downloads on

the relevant

product pages located on Moxa’s website: www.moxa.com

Default Settings

•Default IP address: 192.168.127.253

•Default Subnet Mask: 255.255.255.0

•Default Usernames: admin, user

•Default Password: moxa

Panel Layouts

Front Panel

1. System status LEDs (from left to right)

STATE LED indicator, MSTR/HEAD LED indicator, FAULT LED

indicator, CPLR/Tail LED indicator, SYNC LED indicator

2. USB console port

3. 2 x 10/100/1000BaseT(X) and 2 x 100/1000Base SFP ports

4. 100/1000Base SFP port status LEDs

5. 10/100/1000 BaseT(X) port status LEDs

6. Ethernet module slot 1

7. Ethernet module slot 2

8. Ethernet module slot 3

9. Ethernet module slot 4

10. Ethernet module slot 5

11. Ethernet module slot 6

12. Power module slot 1

13. Power module slot 2

14. Grounding screw

www.ipc2u.ru

www.ipc2u.com

www.moxa.pro

- 3 -

Rear View

1. USB console port

2. USB storage port

3. System LED indicators

4. Module and port LED indicators

5. Rest button

Dimensions

Unit: mm (inches)

Ethernet Modules

LM-7000H-4GTX

LM-7000H-4GSFP

LM-7000H-4GPoE

www.ipc2u.ru

www.ipc2u.com

www.moxa.pro

- 4 -

Power Modules

PWR-HV-P48

PWR-LV-P48

Rack Mounting Instructions

1. Elevated Operating Temperature:If installed in a closed or

multi-unit rack assembly, the operating ambient temperature of the

rack environment may be greater than room temperature.

Therefore, consideration should be given to installing the equipment

in an environment compatible with the maximum ambient

temperature (Tma) specified by the manufacturer.

NOTE

In order to ensure reliable operations, please make sure the

operating temp

erature of the environment does not exceed the

spec. When mounting a rack

-mounted switch with other

operatin

g units in a cabinet without forced ventilation, it is

recommended that 1U of space is reserved between each

rack-mounted switch and/or device.

2. Required Air Flow: Installation of the equipment in a rack should

be such that the amount of air flow required for safe operation of the

equipment is not compromised.

3. Mechanical Loading: Mounting of the equipment in the rack

should be such that a hazardous condition is not achieved due to

uneven mechanical loading.

4. Circuit Overloading: Consideration should be given to the

connection of the equipment to the supply circuit and the effect that

overloading of the circuits might have on overcurrent protection and

supply wiring. Appropriate consideration of equipment nameplate

ratings should be used when addressing this concern.

5. Reliable Grounding: Reliable grounding of rack-mounted

equipment should be maintained. Particular attention should be

given to supply connections other than direct connections to the

branch circuit (e.g. use of power strips).

NOTE

The rackmount ears can be installed on the front or rear of the

PT-G7728/G7828 switch.

ATTENTION

Safety First

Be sure to disconnect the power

cord before installing and/or

wiring your Ethernet Switch. Calculate the maximum possible

current in each power wire and common wire. Observe all

electrical codes dictating the maximum current allowable for each

wire size. If the current goes above the max

imum ratings, the

wiring could overheat,

which can cause

serious damage to your

equipment.

www.ipc2u.ru

www.ipc2u.com

www.moxa.pro

- 5 -

Connecting the Power Inputs

The PT-G7728/PT-G7828 switches support 2 types of power supply:

•PWR-HV-P48: one 110/220 VAC/VDC (90 to 264 VAC, 88 to 300 VDC),

one 48VDC PoE power input for PoE+ ports.

•PWR-LV-P48: one 24/48 VDC (18 to 72 VDC), one 48 VDC PoE power

input for PoE+ ports.

For the PWR-HV-P48, the 110/220 VAC/VDC power supplies provide

power to the switch. Separate 48 VDC power supplies are required to

provide power to all PoE+ ports (50 to 57 VDC is recommended for IEEE

802.3at devices).

For the PWR-LV-P48 models, the 24/48 VDC power supplies provide

power to the switch. Separate 48 VDC power supplies are required to

provide power to all PoE+ ports (50 to 57 VDC is recommended for IEEE

802.3at devices).

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been

switched off or the area is kno

wn to be non-hazardous. The

device may only be connected to the supply voltage shown on the

type plate. The device is designed for operation with a Safety

Extra

-Low Voltage (SELV) or an isolated power supply, which

means that they may only be connected to

the supply voltage

connections and to the signal contact with a SELV or an isolated

power supply in compliance with IEC 60950

-1/EN 60950-

1 or UL

61010.

Power Terminal Blocks

The connection for power input and PoE external power supply is on the

power modules.

PWR-HV-P48

STEP 1: Insert the neutral/line (L/N/Ground) AC wires into the terminals.

STEP 2: Insert the terminal block connector into the terminal block

receptor.

PWR-LV-P48

STEP 1: Insert the negative/positive (-/+) DC wires into the terminals.

STEP 2: Insert the terminal block connector prongs into the terminal

block receptor.

www.ipc2u.ru

www.ipc2u.com

www.moxa.pro

- 6 -

PoE Power Terminal Blocks

STEP 1: Insert the negative/positive DC wires into the -/+ terminals,

respectively.

STEP 2: Insert the terminal block connector prongs into the terminal

block receptor.

NOTE

In order to have higher levels of protection against surge, it is

suggested to install a surge protector in front of the power input

of the

PoE powered device so that it is suitable for use in IEC

61850 conditions.

NOTE

When wiring the power input, we suggest using the cable type -

AWG (American Wire Gauge) 18 (1.03mm2) and the

corresponding pin type cable terminals. The connector must be

able to withs

tand torque at maximum 5 pound-

inches. The rated

temperature of wiring should be at least 105°C.

NOTE

When installing 2 power units on the PT-G7728/G7828 switch,

only power 1 (installed in the upper slot) will activate and provide

power. The other power

unit, power 2 (installed in the lower slot)

will be on standby.

NOTE

The reverse power input connection will not activate the device or

PoE input

. In addition, the PoE will only activate when

the system

power input is installed on the same power unit.

Wiring the Relay Contact

Each power module has one relay output that can provide two types of

relay output. Refer to the table below for detailed information.

The relay contact is used to detect user-configured events. Two wires are

attached to the relay pins with normally close and normally open options.

FAULT:

The relay contact of the 3-pin terminal block connector is used to detect

user-configured events. The module provides normally open and

normally closed circuits depending on what the user chooses. For pin

definitions refer to the table below.

Relay connection Power on state Event trigger

NO and COM

Closed circuit

Open circuit

NC and COM

Open circuit

Closed circuit

NOTE

When wiring the relay contact, we suggest using the cable type -

AWG (American Wire Gauge) 16

-24 (1.31-0.205mm2) and the

corresponding pin type cable terminals. The connector must be

able to withstand torque at maximum 5 pound

-inches.

The rated

temperature of wiring should be at least 105°C.

www.ipc2u.ru

www.ipc2u.com

www.moxa.pro

- 7 -

Install/Remove the Ethernet module

The Ethernet modules are hot-swappable. You have the option to mount

or remove the Ethernet module while the device is operating.

The installation procedure is as follows:

1. Insert the Ethernet module straight into the slot

2. Fasten the module to the device by tightening the 2 screws. The

tightening torque is 3.5 kgf-cm (0.35 Nm)

The removal procedure is as follows:

1. Loosen the 2 screws of the module

2. Pull the module out of the slot

3. Insert the dummy module in to the slot in order to have better

protection against dust and EMI

4. Fasten the dummy module using 2 screws. The tightening torque is

4 kgf-cm (0.40 Nm)

Install/Remove the Power module

The power supply units are hot-swappable. You have the option to mount

or remove the power supply units while the device is operating.

The installation procedure is as follows:

1. Insert the power unit straight into the slot

2. Fasten the unit to the device by tightening the 2 screws. The

tightening torque is 3.5 kgf-cm (0.35 Nm)

The removal procedure is as follows:

1. Loosen the 2 screws of the module

2. Pull the module out of the slot

3. Insert the dummy module in to the slot in order to have better

protection against dust and EMI.

4. Fasten the dummy module using 2 screws. The tightening torque is

4 kgf-cm (0.40 Nm)

NOTE

If one of the modules is removed from the device, it is advisable

to insert a dummy module in order to provide better protection

against dust and EMI.

Grounding the Moxa Industrial Rackmount Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

NOTE

Using a shielded cable achieves better electromagnetic

resistance.

USB Console Connection

The switch has two types of USB port, micro USB-B console port and type

A USB host port. Use a USB cable (type A male to Micro USB-B male) to

connect the USB-serial console port to your PC's COM port, and install the

USB driver (available on Moxa Website) onto the PC. You can then use a

console terminal program, such as Moxa’s PComm Terminal Emulator, to

access the console configuration utility of the switch.

www.ipc2u.ru

www.ipc2u.com

www.moxa.pro

- 8 -

USB Storage Connection

The USB storage port is on the rear panel of the PT-G7728/G7828 switch.

(Type A connector; see the diagram below for pinout assignments). Use

Moxa’s ABC-02-USB automatic backup configurator to connect to the

PT-G7728/G7828 USB storage port in order to perform configuration

backup, firmware upgrade, or system log file backup.

Description

VCC (+5V)

D- (Data-)

D+ (Data+)

GND (Ground)

The Reset Button

The reset button can perform two functions. One is to reset the

PT-G7728/G7828 switch back to factory default settings and the other is

to perform a quick back up of configuration and log files to the

ABC-02-USB automatic backup configurator.

Reset to Factory Default Settings

Depress the Reset button for five seconds to load the factory default

settings. Use a pointed object, such as a straightened paper clip or

toothpick, to depress the Reset button. When you do so, the STATE LED

will start to blink about once per second. Continue to depress the STATE

LED until it begins blinking more rapidly; this indicates that the button has

been depressed for five seconds and you can release the Reset button to

load factory default settings.

NOTE

DO NOT power off the switch when loading default settings.

Configuration and Log Files Back Up

When the ABC-02-USB is connected to the PT-G7728/G7828 switch, the

reset button allows for a quick back up of configuration and event logs to

the ABC-02-USB. Press the reset button to start backing up the current

system configuration files and event logs to the ABC-02-USB.

NOTE

When the ABC-02 is plugged in, you cannot reset to factory

default by pressing the reset button.

LED Indicators

The front panel of the PT-G7728/G7828 switch contains several LED

indicators. The function of each LED is described in the table below.

LED

Color

State

Description

System LEDs

STATE Green

On System has passed self-diagnosis test on

boot-up and is ready to run

Blinking

1. When pressing the reset button for 5

seconds, the LED will blink continuously

(1 time/s) until resetting to factory

default

www.ipc2u.ru

www.ipc2u.com

www.moxa.pro

- 9 -

LED

Color

State

Description

When an ABC-02 automatic backup

device is detected, the LED will blink

slowly (1 time/2s)

Red On

System failed self-diagnosis on boot up.

•Switch Initiate fail

•Fail Firmware Checksum Fail/

Uncompressed Fail

FAULT Red On

One of the following has happened:

1. ABC Loading/Saving Failure

The port has been disabled because the

ingress multicast and broadcast

packets exceed the ingress rate limit

3. Incorrect loop connection in a single

switch

4. The Ring port connection is not valid

Off

System is in normal operation

SYNC

Amber

PTP function is enabled

Blinking

The device is starting to receive the sync

packet

Green On

The PTP function has successfully

converged

MSTR/

HEAD Green

1. This switch is set as the Master of the

Turbo Ring, or as the Head of the

Turbo

Chain.

2. POST H.W. Fail (+State on and Fault

blinking)

Blinking

1. The switch has become the Ring Master

of the Turbo Ring.

2. Head of the Turbo Chain, after the

Turbo Ring or the Turbo Chain went

down.

3. The switch is set as Turbo Chain’s

Member and the corresponding chain

port is down.

Off

The switch is not the Master of this

Turbo Ring.

2. The switch is set as a Member of the

Turbo Chain.

CPLR/

TAIL Green

1. The switch coupling function is enabled

to form a backup path.

2. It is set as the Tail of the Turbo Chain.

3. POST S.W. Fail (+State on and Fault

blinking)

Blinking

1. Turbo Chain is down.

2. The switch is set as Turbo Chain’s

Member and the corresponding chain

port is down.

Off

1. This switch disabled the coupling

function.

2. Set as a Member of the Turbo Chain.

When the system is importing/exporting data from or to an ABC-02-USB

automatic backup device, the FAULT, MSTR/HEAD, and CPLR/TAIL LEDs

will blink in sequence.

www.ipc2u.ru

www.ipc2u.com

www.moxa.pro

- 10 -

LED

Color

State

Description

Port Status LEDs

Ports

1 to 4

Green

On Port's 1000 Mbps link is active

PoE port is connected to PoE device.

Blinking

Data is transmitting at 1000 Mbps

PoE port is connected to PoE device.

Amber

Port's 10/100 Mbps link is active

PoE port is connected to PoE device.

Blinking

Data is transmitting at 10/100 Mbps

PoE port is connected to PoE device.

Red On

PoE power failure:

•Once per second: PoE detection failure

•Twice per second: short-circuit,

overloading, or outside operating

temperature range

Off

Port’s link is inactive

PT-G7728/G7828 (Rear Panel view)

LED

Color

State

Description

System LEDs

STATE

Green

System has passed self-diagnosis test on boot

up and is ready to run

Blinking

1. When pressing the reset button for 5

seconds, the LED will blink continuously

(1 time/s) until resetting to factory

default

2. When an ABC-02 automatic backup

device is detected, the LED will blink

slowly (1 time/2s)

Red On

System failed self-diagnosis on boot-up.

•Switch Initiate fail

•Fail Firmware Checksum Fail/

Uncompressed Fail

FAULT Red On

One of the following has happened:

1. ABC-02 Loading/Saving Failure

2. The port has been disabled because the

ingress multicast and broadcast packets

exceed the ingress rate limit

3. Incorrect loop connection in a single

switch

4. The ring port connection is not valid

Off

System is in normal operation

SYNC Amber

PTP function is enabled

Blinking

The machine is starting to receive the sync

packet

Green

The PTP function is successfully converged.

MSTR/

HEAD Green On

1. This switch is set as the Master of the

Turbo Ring, or as the Head of the Turbo

Chain.

2. POST H.W. Fail (+State on and Fault

blinking)

Blinking

1. The switch has become the Ring Master of

www.ipc2u.ru

www.ipc2u.com

www.moxa.pro

Andere Handbücher für PT-G7728

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Schalten Handbücher

Moxa Technologies

Moxa Technologies IKS-6324 Series Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-G508E-T Handbuch

Moxa Technologies

Moxa Technologies EOM-104 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ETHERDEVICE EDS-305 Handbuch

Moxa Technologies

Moxa Technologies EDS-516A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICS-G7526 Series Handbuch

Moxa Technologies

Moxa Technologies TN-5508A Series Handbuch

Moxa Technologies

Moxa Technologies ToughNet TN-5510-2GLSX-ODC Handbuch

Moxa Technologies

Moxa Technologies EDS-600 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-G2008-EL Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-508 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-2005-ELP Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-4009 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-316 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-7828 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICS-G7526A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPORT 6610 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A Series Handbuch

Moxa Technologies

Moxa Technologies TN-4516A non-PoE series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PowerTrans PT-508-MM-ST-48 Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-510 Series Handbuch

Moxa Technologies

Moxa Technologies RKS-G4028 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung