MPS MP8869S Bedienungsanleitung

User Guide

MP8869S Evaluation Kit (EVKT-8869S)

MP8869S Evaluation Kit User Guide rev 1.0

MonolithicPower.com

7/17/2018

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

USER GUIDE –MP8869S EVALUATION KIT (EVKT-8869S)

Table of Contents

Overview................................................................................................................................................ 3

Section 1. Hardware Specifications........................................................................................................5

1.1 Personal Computer Requirements.............................................................................................. 5

1.2 EV8869S-L-00A Specifications................................................................................................... 5

1.3 EVKT-USBI2C-02 Specifications................................................................................................ 5

Section 2. Software Requirements......................................................................................................... 5

2.1 Software Installation Procedure.................................................................................................. 6

Section 3. Evaluation Kit Test Set-Up..................................................................................................... 7

3.1 Hardware Set-Up........................................................................................................................7

3.2 Powering up the EVB ................................................................................................................. 7

3.3 Software Set-Up......................................................................................................................... 7

3.4 Troubleshooting Tips............................................................................................................... 10

Section 4. Ordering Information............................................................................................................ 11

MP8869S Evaluation Kit User Guide rev 1.0

MonolithicPower.com

7/17/2018

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

USER GUIDE –MP8869S EVALUATION KIT (EVKT-8869S)

Overview

Introduction

The EVKT-8869S is an evaluation kit for the MP8869S. The MP8869S is a highly integrated, high-

frequency, synchronous, step-down switcher with an I2C control interface. The MP8869S is optimized

to support up to 12A continuous/15A peak output current over an input supply range from 2.85V to 18V

with excellent load and line regulation. This kit allows for quick evaluation of the MP8869S. By using the

I2C, users can set the current limit, slew rate, work mode, and output voltage. This device also features

telemetry, which provides output voltage and output current monitoring via I2C.

Kit Contents

EVKT-8869S kit contents: (items below can be ordered separately).

Part Number

Item

Quantity

EV8869S-L-00A

MP8869SGL evaluation board

EVKT-USBI2C-02

Includes one USB to I2C communication interface, one USB

cable, one ribbon cable

Tdrive-8869S

USB flash drive that stores the GUI installation file and

supplemental documents

Figure 1: EVKT-8869S Evaluation Kit Set-Up

Ribbon Cable

MP8869S Evaluation Kit User Guide rev 1.0

MonolithicPower.com

7/17/2018

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

USER GUIDE –MP8869S EVALUATION KIT (EVKT-8869S)

Features and Benefits

The MP8869S is highly customizable. Users can program the MP8869S via the MPS I2C GUI.

All changes made in I2C mode will NOT be retained once the EVB is powered down.

Features adjustable under each method are outlined below.

I2C

•

Adjustable output voltage

•

Slew rate

•

Selectable OVP, OCP mode

•

Selectable PFM mode

•

Selectable PG deglitch time

•

Selectablefrequency

•

Soft stop

•

Adjustable current limit

•

Outputcurrent/voltage monitor

•

System enable (EN bit)

•

Status indication: OC, OTEW, OT, PG

•

Kit Specifications

Features

Specification

Supply for Board

2.85V - 18V

Operating Input Voltage

2.85V - 18V

Output Voltage (VOUT)

Continuous Output Current (IOUT)

12A

Peak Output Current (IOUT)

15A

Operating Systems Supported

Windows XP, 7, or later

System Requirements

Minimum 22.2MB free

GUI Software

3 Register Controls: VSEL, System1, System2

EVB Size (L x W)

8.5cm x 8.5cm

MP8869S Evaluation Kit User Guide rev 1.0

MonolithicPower.com

7/17/2018

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

USER GUIDE –MP8869S EVALUATION KIT (EVKT-8869S)

Section 1. Hardware Specifications

1.1 Personal Computer Requirements

The following must be minimally met to use the EVKT-8869S.

•

Operating System of Windows XP, 7, or later

•

Net Framework 4.0

•

PC with a minimum of one available USB port

•

At least 22.2 MB of free space

1.2 EV8869S-L-00A Specifications

The EV8869S-L-00A is an evaluation board for the MP8869SGL. For more information, please refer to

the EV8869S-L-00A datasheet.

Figure 2: EV8869S-L-00A Evaluation Board

1.3 EVKT-USBI2C-02 Specifications

The EVKT-USBI2C-02 refers to the communication interface, which connects the EVB, the PC, and its

supporting accessories. It provides I2C and PMBus capabilities. Together with MPS Virtual Bench Pro

and GUI tools, it provides a quick and easy way to evaluate the performance of MPS digital products.

For more details, refer to the EVKT-USBI2C-02 datasheet.

Figure 3: EVKT-USBI2C-02 Communication Interface

Section 2. Software Requirements

Feature

Specification

Supply for Evaluation Board

2.85V - 18V

Operating Input Voltage

2.85V - 18V

Output Voltage (VOUT)

Continuous Output Current (IOUT)

12A

Peak Output Current (IOUT)

15A

EVB Size (L x W)

8.5cm x 8.5cm

MP8869S Evaluation Kit User Guide rev 1.0

MonolithicPower.com

7/17/2018

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

USER GUIDE –MP8869S EVALUATION KIT (EVKT-8869S)

2.1 Software Installation Procedure

Programming occurs through the MPS I2C GUI. Follow the instructions below to install the software.

Note: In the near future, this software can be downloaded from the MPS website. For now, it is provided

on a USB thumb drive.

1. Plug the thumb drive into the computer using any available USB port.

2. Locate the folder containing the thumb drive contents.

3. Double click the .exe file to open the set-up guide (see Figure 4).

4. Follow the prompts in the set-up guide.

5. Wait for the status screen to verify that installation is complete (see Figure 5).

Figure 4: MPS I2C GUI Set-Up Guide

Figure 5: MPS I2C GUI Set-Up Success

MP8869S Evaluation Kit User Guide rev 1.0

MonolithicPower.com

7/17/2018

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

USER GUIDE –MP8869S EVALUATION KIT (EVKT-8869S)

Section 3. Evaluation Kit Test Set-Up

3.1 Hardware Set-Up

The hardware must be configured properly prior to use. Use the USB cable to connect the EVKT-

USBI2C-02 communication interface to the PC, and follow the instructions below to set up the EVB.

1. Locate the proper wires to connect the EVB to the EVKT-USBI2C-02 communication interface.

2. Connect SCL, SDA, and GND (see Figure 6). If needed, refer to the datasheet for further clarification.

Figure 6: EVB to MPS I2C Communication Interface Wire Connection

3.2 Powering up the EVB

1. Connect the positive and negative terminals of the load to the VOUT and GND pins, respectively.

2. Preset the power supply output between 4.5V and 21V, and then turn off the power supply.

3. Connect the positive and negative terminals of the power supply output to the VIN and GND pins,

respectively.

4. Turn the power supply on. The MP8869S will enter the power-on sequence automatically.

3.3 Software Set-Up

After connecting the hardware according to the above steps, follow the steps below to use the GUI

software.

1. Start the software. It will automatically check the EVB connection.

•

If the connection is successful, the address will be listed in the “Slave Address” (see Figure 7).

MP8869S Evaluation Kit User Guide rev 1.0

MonolithicPower.com

7/17/2018

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

USER GUIDE –MP8869S EVALUATION KIT (EVKT-8869S)

Figure 7: Appearance of Address Shows Successful Connection

•

If not, a warning will appear at the bottom. There are two warnings users can expect.

1) “EVB is disconnected!”This means that the evaluation board is not connected (see Figure 8).

2) “Communication Board is disconnected!”This means that the USB I2C communication

interface is not connected.

Figure 8: Warning Indicates Unsuccessful Connection –Evaluation Board not Connected

Communication

Board is

Disconnected

Invalid Slave Address

EVB is Disconnected

MP8869S Evaluation Kit User Guide rev 1.0

MonolithicPower.com

7/17/2018

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

USER GUIDE –MP8869S EVALUATION KIT (EVKT-8869S)

2. If the connection is successful, proceed to Step 3. Otherwise, check connections between the EVB,

communication interface, and PC. Re-plug the USB into the computer and restart the GUI.

3. Click the PartSelect button to select the MP8869S (see Figure 7) (The default GUI window is for

the MP8861). The Register Control menu will appear on the left side. I2C register values will be

read and displayed on the right side after clicking the Read button (see Figure 9).

Figure 9: Values from I2C Shown in Table

4. Find the item you want to change and select the desired value from the drop-down menu.

5. Click the Read All button to update values. The changed information of the item will appear on the

right side (see Figure 10).

Figure 10: Refer to Datasheet to Translate 0’s and 1’s

All changes made via I2C will be restored to default values once the EVB is powered down.

MP8869S Evaluation Kit User Guide rev 1.0

MonolithicPower.com

7/17/2018

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

USER GUIDE –MP8869S EVALUATION KIT (EVKT-8869S)

3.4Troubleshooting Tips

Note: USBI2C-02 and USBI2C-01 drivers are not compatible. USBI2C-02 uses USBXpress and USBI2C

uses Cyusb3. USBI2C-02 is the recommended device for MPS PMBus and I2C.

EVKT-USBI2C-01

In case that the USBI2C-01 driver is not properly

installed, manual installation is required. Follow the

steps below.

1. Open the Device Manager and select update driver

software (see Figure 11).

2. Click “Browse my computer for driver software”, find

the driver located on thumb drive and install.

EVKT-USBI2C-02

In the case that the USBI2C-02 driver is not properly

installed, manual installation is required. Follow the

steps below.

Note: Check driver version. Find “USBXpress” Device in

the Device Manager under USB controllers.

Right click and view properties. Check to make sure the

driver version matches the newest version (see Figure

12).

1. Browse the thumb drive contents and open the

driver’s folder.

2. Install the correct USBXpress “.exe” file.

Choose either 32 bit or 64 bit operating system.

32-bit: USBXpressInstaller_x86.exe

64-bit: USBXpressInstaller_x64.exe

3. Connect the EVKT-USBI2C-02 Dongle to the PC

with the USB cable.

•

No Supply

The MP8869S’s input pin has an under-voltage lockout

(UVLO) detection circuit. If the input voltage (AVIN) is lower than the UVLO rising threshold, the

MP8869S’s functions are disabled.

•

Shutdown Event

If the MP8869S detects that the input voltage is lower than the UVLO falling threshold (enter no supply

state) or over-temperature protection is triggered (enter power-off state), the MP8869S switches to no

supply state or power-off state, regardless of the current state.

•

Thermal Recovery

If the MP8869S is in a power-off state due to the die temperature exceeding the thermal protection

threshold, the MP8869S enters a power-on sequence when the die’s temperature decreases.

•

Shutdown Sequence

When the input voltage is lower than the UVLO falling threshold or the IC is over-temperature, the

MP8869S enters the shutdown sequence directly.

Figure 12: Correct Driver Version

Figure 11: Updating the Driver Software

Inhaltsverzeichnis

Andere MPS Hauptplatine Handbücher

MPS

MPS EVHR2000-S-00A Bedienungsanleitung

MPS

MPS EV0035 Bedienungsanleitung

MPS

MPS EVKT-MACOM Bedienungsanleitung

MPS

MPS EV3209DJ-00A Bedienungsanleitung

MPS

MPS MP2672 Bedienungsanleitung

MPS

MPS EV0030 Bedienungsanleitung

MPS

MPS EV26059DQ-00B Bedienungsanleitung

MPS

MPS EVmEZDPD3603A-00A Bedienungsanleitung

MPS

MPS EV6551-QB-00A Bedienungsanleitung

MPS

MPS EV1477-TF-00B Bedienungsanleitung

MPS

MPS EV2483DQ-00C Bedienungsanleitung

MPS

MPS EVQ6541A-QK-00A Bedienungsanleitung

MPS

MPS EV8042DF-00B Bedienungsanleitung

MPS

MPS EV2759-Q-00A Bedienungsanleitung

MPS

MPS EVKT-MP8860 Bedienungsanleitung

MPS

MPS EV28163-Q-00A Bedienungsanleitung

MPS

MPS EV2602DQ-00B Bedienungsanleitung

MPS

MPS EVKT6515 Bedienungsanleitung

MPS

MPS EV3205DJ-00A Bedienungs- und Wartungsanleitung

MPS

MPS MP2696A Referenzhandbuch

MPS

MPS EV7740DN-01B Bedienungsanleitung

MPS

MPS EV2632-R-01A Bedienungsanleitung

MPS

MPS MP5416 Bedienungsanleitung

MPS

MPS EV2605DQ-00B Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung