MrCool DIY E Star Series Bedienungsanleitung

Easy Do-It-Yourself installation

with our Quick Connect®line set*

Installing the MRCOOL DIY® does not require specialized tools or

training. However, it does require basic technical skills. You are assuming

the risk by handling materials containing refrigerants under pressure,

that if not handled properly, can cause bodily injury. If you do not feel

comfortable conducting this installation process yourself, we recom-

mend you retain the services of a qualied HVAC professional.

www.mrcool.com

DIY

E Star™Series

4th GEN Do-It-Yourself Ductless Mini-Split Heat Pump A/C

SMART CONTROLLER

***************Note****************

This guide is for convenience. Please

refer to the installation manual for

more detailed instructions and

descriptions.

Version Date: 10-14-21

*Pat. https://mrcool.com/mrcool-patents/

1. Drill screw holes at the indicated points into the wall

studs.

2. Remove the mounting bracket from the rear of the

interior air handler by removing the screw(s) holding it in

place.

3. Screw the metal bracket to the wall according to the

template.

4. Use a level to

ensure the

mounting plate is

ﬂush and level.

1. Locate the cardboard wall template.

2. Place the template on the wall at the installation location.

3. Use the template

to mark the location

of the drill points for

the mounting screws

and wall hole. Make

sure that the drill

points for the mounting

screws are located on

wall studs.

4. Remove the template.

Wall

Indoor Outdoor

0.2 - 0.3in

(5 - 7 mm)

STEP 1 - inside

STEP 3 - inside

STEP 2 - inside

1. Drill a 3.5 inch diameter hole through the wall, at a

slightly downward angle (to ensure proper drainage), to

accommodate the line set, condensate drain line, and MC

cable to the exterior condenser.

2. Carefully bend piping at the back of the air handler until

it is sticking straight out from behind the unit.

3. Using electrical tape, lightly tape the refrigerant piping &

condensate drain line at the back of the indoor unit into a

bundle (this will make it easier to pass through the wall

hole). The drain pipe MUST be on the bottom. DO NOT

wrap the end of the piping (connectors & drain hose)

you will need access to them for later steps.

4. Insert wall hole sleeve into wall hole.

5. Push the MC cable and piping bundle through the wall

hole. condensate

drain line

Refrigerant

piping

Drain hose

Tape

4. Snap the air handler onto the wall bracket by leaning the

top towards the wall and hooking it on the top of bracket.

Then, apply pressure to the bottom half to snap it to the

bracket.

1. Place outside condenser unit ﬁrmly on the ground or

attach it to a secure metal wall bracket or pad. A drain pipe

underneath the unit is not required unless the unit is

elevated. Please refer to the manual for more information.

2. Install the wall hole ﬁnishing cap/seal. Then, carefully

bend the piping coming out of the exterior wall hole (from

the indoor unit) down towards the wall.

3. Remove the plastic seals from the indoor handler

refrigerant lines.

4. Carefully unroll one end of the Quick Connect® line set*.

Only unroll the amount needed to connect to the indoor

handler ﬁttings. Leave the remainder coiled.

5. Align the Quick Connect® ﬁttings of the refrigerant line

set to the matching indoor handler ﬁttings. Tighten the ﬁrst

few threads by hand.

6. Using two open-ended wrenches, or crescent

(adjustable-type) wrenches, and the image below as a

guide: place the wrenches on points marked “1” & “2,” only

turning the nut at the point marked “2.” Ensure that the

screw connector does not become crooked while working

quickly to tighten it. Tighten the connector until snug.

7. Then, tighten the connector slightly beyond that point to

apply torque to the connector. Repeat the same steps for

the second line. Please refer to the manual for information

about torque requirements for the connectors.

Minimum Clearance between

the back of unit and wall:

**Ground Installed:

12 in (30 cm)

**Bracket Installed:

6 in (15 cm)

Minimum Clearance

in front of unit:

79 in (200 cm)

Minimum Clearance

on the left side of unit:

12 in (30 cm)

Minimum Clearance

above unit:

24 in (60 cm)

Minimum Clearance

on the right side of unit:

24 in (60 cm)

STEP 3 - Continued

STEP 4 - Outside

STEP 4 - Continued

*Pat. https://mrcool.com/mrcool-patents/

1. Carefully roll the excess tubing and place it behind the

condenser, lying ﬂat on the ground.

2. Align the line set connectors to the outside condenser

and tighten the ﬁrst few threads by hand. NOTE: Make

sure the piping connection to outside unit has plenty of

slack and line set is not stressed.

Carefully unroll to indoor

handler connection

Connect directly to

exterior condensor

Keep excess coiled

Radius

3. Using two open-ended wrenches, or crescent

(adjustable-type) wrenches, and the image below as a

guide: you will now tighten the bottom screw connector.

Place wrenches on points marked “1” & “2,” only turning the

nut at the point marked “2.” Ensure the screw connector

does not become crooked as you work quickly to tighten it.

Tighten the connector

until it is snug.

4. Then, tighten the

connector slightly

beyond that point to

apply torque the the

connector. Please

refer to the manual

for information about

torque requirements.

Repeat the same

steps for the top

screw connector.

1. Starting with the top valve, using an open-ended wrench,

or crescent (adjustable-type) wrench, remove the brass cap

from the valve on the outside unit.

2. Then, insert a 5 mm Allen wrench to open the valve by

turning it counter-clockwise until it stops turning. DO NOT

force it.

NOTE: When opening the valves you may hear a soft

hissing sound as a slight amount of R-410a refrigerant

exits the condenser.

3. Reinstall the cap and tighten securely.

4. Repeat the same steps for the bottom valve.

5. Using soapy water (in a spray bottle or with a brush), or

leak detection spray, apply to the Quick Connect® ﬁttings at

the indoor air handler and outdoor condenser to check for

leaks. If you see bubbles begin to form, this indicates there

is a leak. If so, retighten the connection accordingly until

the bubbles are gone. Please refer to the manual for more

detailed information on checking for leaks.

STEP 6 - OutsideSTEP 5 - Outside

1. Remove the screws that attach the electrical cover to the

outdoor condenser.

2. Remove the large retaining nut from the end of the MC

Cable coming from the indoor air handler.

3. Now push the threaded end of the MC Cable through the

hole in the electrical cover you removed form the outdoor

condenser. Then, thread the retaining nut back onto the

end of the MC cable. Please refer to the images below.

4. Now, ﬁrmly and securely connect the wires of the MC

cable to the appropriate terminals of the outdoor

condenser by screwing the U-lug connector of each wire to

the correct terminal. NOTE: Wires and terminals that are

numbered should be matched and connected

accordingly. If the unit is a 115 volt system (12K), hook

to terminals _L_ and _N_ and Ground. If the unit is a

208/230 volt system (all other sizes), hook to terminals

_L1_ and _L2_ and Ground. Use the image and wiring

illustrations to the bottom left as a guide.

WARNING

BEFORE PERFORMING ANY ELECTRICAL WORK, TURN OFF ALL

POWER TO THE SYSTEM.

1. Wire colors of this series / model may diﬀer from previous

models, other series and general conventions.

2. All wiring must be performed in accordance with the

wiring diagrams shown here and all municipal, state and

federal regulations.

4. Be sure to know whether your unit is 115 volt (12K only) or

208/230 volt (all other sizes). Incorrect voltage can cause

serious damage to the system and void the warranty.

5. A certiﬁed electrician is required to supply power from a

disconnect of an appropriate rating - see manual.

STEP 7 - Outside

GREEN Y/G

32 L1L21

21 L1L2

WIRE CONNECTING DIAGRAM

OUTDOOR UNIT TERMINAL

TO INDOOR UNIT 208/230V

POWERSUPPLY

GREEN Y/G

32 L N1

21 L N

OUTDOOR UNIT TERMINAL

TO INDOOR UNIT 115V

POWERSUPPLY

WIRE CONNECTING DIAGRAM 12K

models

only

all

other

models

RED

WHITE

BLACK

RED

WHITE

1. Install the provided batteries into the remote control.

2. Press the Power button on the remote control.

3. The MRCOOL®DIY®Series should activate automatically.

4. To use the MRCOOL® Smartphone App, refer to the

Smart Controller Module instructions included in the box.

STEP 7 - Continued

STEP 9 - Inside

1. Pack the wall hole with the supplied Neoprene (or Spray

Foam), ﬁlling any space not taken up by the piping & lines,

in order to seal the hole.

2. To protect Quick Connect®connections and reduce

vibration, wrap them with the black sound deadening pads.

Then install the white pipe insulation over the pads.

3. Now, starting where the line set is not covered with the

factory plastic (close to the indoor air handler connection,

you will wrap the line set upward, using the supplied

Non-adhesive U.V. tape to the wall hole. This will cover the

insulated line set connections, cables, and drain hose. The

drain pipe will need to be at the bottom of the bundle.

Refer to the diagram on the previous page. DO NOT wrap

the end of the drain hose.

4. To further improve overall appearance and long-term

durability of the line set, it is recommended to install an

optional MRCOOL®LineGuard® (sold separately).

wrap line set upward to the wall

hole to ensure rain/water does

not get into tape/wrap overlaps

Quick Connect

connections

Non-Adhesive

U.V. Tape

(Wrap)

keep line excess

bundled and coiled

lying flat behind

unit

Wrap the Quick Connect®

connections with the black

sound deadening pads. Then

place insulation over them

before the connection is

wrapped Non-adhesive U.V.

Tape

Refrigerant

piping

Drain hose

Non-Adhesive U.V.

Tape

STEP 8 - Outside

5. Finally, reinstall the electrical wiring cover and secure it

by reinstalling the screws you previously removed.

Quick Connect® Line Set

(refrigerant pipe)

Pat. https://mrcool.com/mrcool-patents/

Andere Handbücher für DIY E Star Series

Dieses Handbuch passt für folgende Modelle

Andere MrCool Klimaanlage Handbücher

MrCool

MrCool DIY E Star Series Technisches Handbuch

MrCool

MrCool Oasis Series Bedienungsanleitung

MrCool

MrCool Advantage Series Bedienungsanleitung

MrCool

MrCool Advantage Series Bedienungsanleitung

MrCool

MrCool DIY Series Bedienungsanleitung

MrCool

MrCool Signature Series Bedienungsanleitung

MrCool

MrCool Signature MCVP Series Bedienungsanleitung

MrCool

MrCool Advantage Series Bedienungsanleitung

MrCool

MrCool Advantage Series Bedienungsanleitung

MrCool

MrCool DIY E Star Series Betriebsanleitung

MrCool

MrCool DIY Series Bedienungsanleitung

MrCool

MrCool DIY-MULTI2-18HP230C Bedienungsanleitung

MrCool

MrCool Olympus Series Bedienungsanleitung

MrCool

MrCool O-09-HP-WMAH-230A Bedienungsanleitung

MrCool

MrCool 18 Series Bedienungsanleitung

MrCool

MrCool DIY E Star Series Technisches Handbuch

MrCool

MrCool MAC13018 Bedienungsanleitung

MrCool

MrCool PRODIRECT Series Kurzanleitung

MrCool

MrCool Olympus Hyper Heat Series Bedienungsanleitung

MrCool

MrCool Signature MAC16 A Series Bedienungsanleitung

MrCool

MrCool DIY E Star Series Betriebsanleitung

MrCool

MrCool DIY Series Bedienungsanleitung

MrCool

MrCool PTAC 5 Series Betriebsanleitung

MrCool

MrCool DIY E Star Series Kurzanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Spheros

Spheros CC 355 Bedienungsanleitung

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Bedienungsanleitung

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Samsung

Samsung AR KV Series Leitfaden

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

Hitachi

Hitachi RAS-E24CAK Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Hisense

Hisense 7K Technisches Handbuch

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung