MSA Fieldserver ProtoNode Bedienungsanleitung

Operating Manual

ProtoNode Start-up Guide

Revision: 3.G

Document No.:T18610

Print Spec: 10000005389 (F)

MSAsafety.com

MSA Safety

1991 Tarob Court

Milpitas, CA 95035

U.S. Support Information:

+1 408 964-4443

+1 800 727-4377

Email: [email protected]

EMEA Support Information:

+31 33 808 0590

Email: [email protected]

For your local MSA contacts, please go to our website www.MSAsafety.com

Contents

1 About the MSA FieldServer ProtoNode 5

1.1 Certification 5

2 BACnet/LonWorks Setup through ProtoNode 6

2.1 Features 6

2.2 Installation Steps for the Customer 6

2.3 Record Identification Data 6

2.4 Configure the DIP Switches 7

2.4.1 Setting the Node/ID Device Instance (DIP Switch A0 – A7) 7

2.4.2 Setting the Serial Baud Rate (DIP Switch B0 – B3) 7

2.4.3 Select and Load Configuration Files 8

3 Interfacing ProtoNode to Host OEM Device 9

3.1 ProtoNode FPC-N34 and FPC-N35 Showing Connection Ports 9

3.2 Device Connections to ProtoNode 10

3.3 Resistor and Power Jumper Information 11

3.3.1 Bias Resistors 11

3.3.2 Termination Resistor 12

3.3.3 Power Jumper Settings 12

3.4 Wiring Field Port to RS-485 BMS Network 13

3.5 Wiring Field Port to a LonWorks Network 13

4 Power up the ProtoNode 14

5 Connect the PC to the Gateway 15

5.1 Connecting to the Gateway via Ethernet 15

5.1.1 Changing the Subnet of the Connected PC 15

5.2 Navigate to the Login Page 15

6 Setup Web Server Security 16

6.1 Login to the FieldServer 16

6.2 Select the Security Mode 18

6.2.1 HTTPS with Own Trusted TLS Certificate 19

6.2.2 HTTPS with Default Untrusted Self-Signed TLS Certificate or HTTP with Built-in Payload Encryption 19

7 Configure the FieldServer 20

7.1 Setting IP Address for Field Network 20

7.1.1 Accessing the FieldServer Manager 21

8 LonWorks (FPC-N35): Commissioning the ProtoNode on a LonWorks Network 22

8.1 Commissioning theProtoNode FPC-N35 on a LonWorks Network 22

8.1.1 Instructions to Download XIF File from ProtoNode FPC-N35 Using Browser 22

9 Troubleshooting 24

9.1 Lost or Incorrect IP Address 24

9.2 Viewing Diagnostic Information 25

9.3 Checking Wiring and Settings 26

9.4 Taking a FieldServer Diagnostic Capture 27

9.5 LED Functions 28

ProtoNode Start-up Guide 3

9.6 Internet Browser Software Support 28

10 Additional Information 29

10.1 Update Firmware 29

10.2 BACnet: Setting Network_Number for more than one ProtoNode on Subnet 29

10.3 Reading Data Arrays 30

10.4 Change Web Server Security Settings After Initial Setup 31

10.4.1 Change Security Mode 32

10.4.2 Edit the Certificate Loaded onto the FieldServer 33

10.5 Change User Management Settings 34

10.5.1 Create Users 35

10.5.2 Edit Users 36

10.5.3 Delete Users 37

10.5.4 Change FieldServer Password 38

10.6 Routing Settings 39

10.7 Specifications 40

10.8 Compliance with UL Regulations 41

10.9 A Bank DIP Switch Settings 42

11 Limited 2 Year Warranty 46

4 ProtoNode Start-up Guide

1 About the MSA FieldServer ProtoNode

The MSAFieldServer ProtoNode is an external, high performance, Building and Industrial Automation multi-protocol

gateway for OEMs wanting to provide protocol translation between Serial and Serial, Serial-Ethernet and Ethernet-Ethernet

devices using LonWorks®, BACnet®, Metasys®N2 by JCI, Modbus, DNP 3.0, and more. This manual provides installation

information for 2 types of customers:

• OEMs that have purchased the product to be used with their controllers and have not done a first time start with their

controller. When the OEM completes the programming of the ProtoNode with their device, the gateway will be virtually

plug and play at the OEMs customer sites.

◦ The OEM follows all the steps in this guide to complete the first time start up

• End Users that have purchased the pre-programmed gateway from one of our OEM customers and need some

instructions to configure the device.

The ProtoNode is always pre-configured by the OEM, requiring the end customer to set DIP switches or input fields in a web

configuration GUI to load a configuration file and set the specific network setting of the device.

NOTE:For troubleshooting assistance refer to Section 9 Troubleshooting, or any of the troubleshooting

appendices in the related driver supplements. Check the MSA Safety website for technical support resources

and documentation that may be of assistance.

The ProtoNode is cloud ready and connects with MSA Safety’s Grid. See Section 7.1.1 Accessing the FieldServer

Manager for further information.

1.1 Certification

BTL Mark – BACnet Testing Laboratory

The BTL Mark on the FieldServer is a symbol that indicates that a product has passed a series of

rigorous tests conducted by an independent laboratory which verifies that the product correctly

implements the BACnet features claimed in the listing. The mark is a symbol of a high-quality BACnet

product.

Go to www.BACnetInternational.net for more information about the BACnet Testing Laboratory. Click

here for the BACnet PIC Statement. BACnet is a registered trademark of ASHRAE.

LonMark Certification

LonMark International is the recognized authority for certification, education, and promotion of

interoperability standards for the benefit of manufacturers, integrators and end users. LonMark

International has developed extensive product certification standards and tests to provide the integrator

and user with confidence that products from multiple manufacturers utilizing LonMark devices work

together. MSA Safety has more LonMark Certified gateways than any other gateway manufacturer,

including the QuickServer, ProtoCessor, ProtoCarrier and ProtoNode for OEM applications and the full

featured, configurable gateways.

ProtoNode Start-up Guide 5

2 BACnet/LonWorks Setup through ProtoNode

2.1 Features

• 10/100BaseT Ethernet LAN interface (auto-sensing)

• Multiple Protocol Support

• Supports multiple configuration files and the ability to automatically load any of the stored files for different OEM

controllers or protocols supported.

• ProtoNode- FPC-N34/N38

◦ FPC-N34: 2 RS-485 ports and 1 Ethernet port

◦ FPC-N38: 1 RS-485 port, 1 Ethernet port and 1 RS-232

• ProtoNode- FPC-N35/N39

◦ FPC-N35: 1 Ethernet Port, 1 LonWorks port and 1 RS-485 port

◦ FPC-N39: 1 Ethernet Port, 1 LonWorks port and 1 RS-232 port

• ProtoNode- FPC-N40

◦ FPC-N40: 1 RS-485 port, 1 Ethernet port and KNX port

• ProtoNode- FPC-N42

◦ FPC-N42: 1 RS-485 port, 1 Ethernet port and M-Bus port

2.2 Installation Steps for the Customer

1. Record the information about the unit. (Section 2.3 Record Identification Data)

2. Set the A, B, and S DIP Switch banks for field protocol baud rate, Node-ID/Device Instance, and proper

configuration. (Section 2.4 Configure the DIP Switches)

3. Connect the ProtoNode to the field protocol port and customer’s port to the ProtoNode’s RS-485 interface. (Section

3.4 Wiring Field Port to RS-485 BMS Network)

4. Connect power to the ProtoNode.

5. Where the field protocol is BACnet/IP or Modbus TCP/IP, refer to Section 3 Interfacing ProtoNode to Host OEM

Device to run the Web GUI and change the IP Address. No changes to the configuration file are necessary.

6. Use a web browser to access the FieldServer Web Configurator page to enter any necessary device information.

the FieldServer automatically builds and loads the appropriate configuration.

2.3 Record Identification Data

Each ProtoNode has a unique part number located on the side or the back of the unitside of the label. The number format is

FPC-N34-XXXX. This number should be recorded, as it may be required for technical support.

Part Number: __________________________________________________

6 ProtoNode Start-up Guide

2.4 Configure the DIP Switches

2.4.1 Setting the Node/ID Device Instance (DIP Switch A0 – A7)

• The A Bank DIP switches on the ProtoNode allow users to set the Node-ID/Device Instance on the Field RS-485.

• DIP switches A0 – A7 can also be used to set the MAC Address for BACnet MS/TP and BACnet/IP.

NOTE: When setting DIP Switches, please ensure that power to the board is OFF.

• Refer to Section 10.9 A Bank DIP Switch Settings for the full range of addresses to set Node-ID/Device Instance.

2.4.2 Setting the Serial Baud Rate (DIP Switch B0 – B3)

• DIP Switches B0 – B3 can be used to set the serial baud rate to match the baud rate provided by the interfaced systems.

• Metasys N2 is always defaulted to 9600 baud and the B bank is disabled.

• “B” bank DIP switches B0 – B3 are disabled on ProtoNode FPC-N35 (LonWorks).

ProtoNode Start-up Guide 7

Baud Rate Dip Switch Selection

Baud B0 B1 B2 B3

9600 On On On Off

19200 Off Off Off On

38400* On On Off On

57600 Off Off On On

76800 On Off On On

* Factory default setting = 38400

2.4.3 Select and Load Configuration Files

• The S bank of DIP switches, S0 - S3 is used to select and load a configuration file from a group of pretested/preloaded

configuration files that the OEM has programmed for their end users.

• End customers will need to go back to the OEM of the device that they are installing to get the DIP settings for the

ProtoNode. The ProtoNode part number will need to be provided to identify the unit.

8 ProtoNode Start-up Guide

3 Interfacing ProtoNode to Host OEM Device

3.1 ProtoNode FPC-N34 and FPC-N35 Showing Connection Ports

ProtoNode Start-up Guide 9

The top 3 pin port will always be R1, unless it’s a LonWorks ProtoNode in which case the port designation is LonWorks (and

the port is 2 pins). The bottom 6 pin port will be R2.

NOTE:The 6 pin port can be RS-232, RS-485 or KNX (and we use the left 3 pins for this as currently shown).

3.2 Device Connections to ProtoNode

ProtoNode 6 Pin Phoenix connector for RS-485 Devices

• The 6 pin Phoenix connector is the same for ProtoNode FPC-N34 (BACnet) and FPC-N35 (LonWorks).

• Pins 1 through 3 are for Modbus RS-485 devices.

◦ The RS-485 GND (Pin 3) is not typically connected

• Pins 4 through 6 are for power. Do not connect power until Section 4 Power up the ProtoNode.

10 ProtoNode Start-up Guide

Inhaltsverzeichnis

Andere MSA Tor Handbücher

MSA

MSA FieldServer QuickServer FS-QS-1011 Benutzerhandbuch

MSA

MSA fieldserver QuickServer FS-QS-2 0 Series Benutzerhandbuch

MSA

MSA fieldserver ProtoAir FPA-C41 Bedienungsanleitung

MSA

MSA FieldServer ProtoNode FPC-N34 Benutzerhandbuch

MSA

MSA FieldServer ProtoCarrier FPC-C34 Benutzerhandbuch

MSA

MSA HUB Bedienungsanleitung

MSA

MSA fieldserver ProtoCarrier Bedienungsanleitung

MSA

MSA MultiGard 5000 Bedienungsanleitung

MSA

MSA fieldserver EZ Series Bedienungsanleitung

MSA

MSA FieldServer FGFD ProtoAir Bedienungsanleitung

MSA

MSA QuickServer FS-QS-2XX0 Bedienungsanleitung

MSA

MSA FS-EZX-KNX-BAC Benutzerhandbuch

MSA

MSA fieldserver ProtoNode FPC-N54 Benutzerhandbuch

MSA

MSA ProtoAir FPA-C4X Benutzerhandbuch

MSA

MSA FieldServer FS-B35 Series Benutzerhandbuch

MSA

MSA fieldserver ProtoNode FPC-N64 Benutzerhandbuch

MSA

MSA fieldserver EZ Gateway M-Bus to Modbus &... Benutzerhandbuch

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

MSA fieldserver ProtoNode Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken