MSA Altair Bedienungsanleitung
Altair®
SingleGasDetector
OperatingManual
Altair®
Detectordeunsólogas
ManualdeOperación
Altair®
Détecteurmono-gaz
Moded’emploi
InNorthAmerica,tocontactyourneareststockinglocation,dialtoll-free1-800-MSA-2222
TocontactMSAInternational,dial1-724-776-8626or1-800-MSA-7777
©MINESAFETYAPPLIANCESCOMPANY2011-AllRightsReserved
Thismanualisavailableontheinternetatwww.msanet.com
ParacomunicarseconellugardeabastecimientomáscercanoenAméricadelNorte,llamegratisal
1-800-MSA-2222.ParacomunicarseconMSAInternational,llameal1-724-776-8626ó1-800-MSA-7777
©MINESAFETYAPPLIANCESCOMPANY2011.Sereservantodoslosderechos.
EstemanualpuedeobtenerseenlaInternet,enelsitio:www.msanet.com.
EnAmériqueduNord,pourcontacternotredépôtleplusproche,composezlenumérogratuit
1-800-MSA-2222pourcontacterMSAInternational,composezle1-724-776-8626ou1-800-MSA-7777
©MINESAFETYAPPLIANCESCOMPANY2011-Tousdroitsréservés.
Cemanuelestdisponiblesurl’Internetauwww.msanet.com.
PRODUCTOFU.S./PRODUCTODEEE.UU. /PRODUITDESÉ-U.
MSANORTHAMERICA
1000Cranberry oodsDrive,CranberryTownship,Pennsylvania16066
(L)Rev.4 Y-HLR 10068081
Altair®
SingleGasDetector
Operating anual
InNorthAmerica,tocontactyourneareststockinglocation,dialtoll-free1-800- SA-2222
Tocontact SAInternational,dial724-776-8626or1-800- SA-7777
© INESAFETYAPPLIANCESCO PANY2011-AllRightsReserved
Thismanualisavailableontheinternetatwww.msanet.com
PRODUCTOFU.S.
SANORTHA ERICA
1000CranberryWoodsDrive,CranberryTownship,Pennsylvania16066
(L)Rev4 Y-HLR 10068081
i
THIS ANUAL USTBECAREFULLYREADBYALLINDIVIDUALSWHOHAVEORWILL
HAVETHERESPONSIBILITYFORUSINGORSERVICINGTHEPRODUCT.Likeanypiece
ofcomplexequipment,thisinstrumentwillperformasdesignedonlyifitisusedand
servicedinaccordancewiththemanufacturer’sinstructions.OTHERWISE,ITCOULD
FAILTOPERFOR ASDESIGNEDANDPERSONSWHORELYONTHISPRODUCTFOR
THEIRSAFETYCOULDSUSTAINSEVEREPERSONALINJURYORDEATH.
Thewarrantiesmadeby ineSafetyAppliancesCompanywithrespecttotheproduct
arevoidediftheproductisnotusedandservicedinaccordancewiththeinstructionsin
thismanual.Pleaseprotectyourselfandothersbyfollowingthem.Weencourageour
customerstowriteorcallregardingthisequipmentpriortouseorforanyadditional
informationrelativetouseorrepairs.
! WARNING
TableofContents
Chapter1,
InstrumentSafetyandCertifications ......1-1
! WARNIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Chapter2,
UsingtheAltairSingleGasDetector ......2-1
Figure 2-1. Altair Overview . . . . . . . . . . . . . . . . . . .2-1
Figure 2-2. Altair Display . . . . . . . . . . . . . . . . . . . . .2-1
Changing Alarm Setpoints . . . . . . . . . . . . . . . . . . . . . . .2-1
To change Alarm setpoints before activation: . . . . . . .2-2
Figure 2-3. Changing the Alarm Setpoints . . . . . . . .2-3
Activating the Altair Single as Detector . . . . . . . . . . . .2-4
Figure 2-4. Altair Activation Flow Chart . . . . . . . . . .2-6
Time Remaining (check before each day’s use) . . . . .2-7
Confidence Indicator (see Figure 2-2) . . . . . . . . . . . . .2-8
Altair Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
Toxic as Measurements (see figure 2-1) . . . . . . . . .2-8
Oxygen Measurements . . . . . . . . . . . . . . . . . . . . . . . . .2-9
! WARNIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
Accessing the Instrument Pages . . . . . . . . . . . . . . . . .2-10
Figure 2-5. Accessing Altair Pages Flow Chart . . .2-11
Event Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12
Chapter3,
AltairFunctionChecks..................3-1
Confidence and Heartbeat Indicator . . . . . . . . . . . . . .3-1
Alarm Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Bump Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Table 3-1. Calibration/Bump Test Values . . . . . . . .3-3
Figure 3-1. Bump Test Flow Chart . . . . . . . . . . . . . .3-3
ii
Chapter4,
CalibratingtheAltairSingleGasDetector ..4-1
Calibrating the Toxic as Instruments (CO and H2S) . .4-2
!WARNIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Figure 4-1. Calibration (Toxics) Flow Chart
(part 1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
Figure 4-1. Calibration (Toxics) Flow Chart
(part 2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
Calibrating an Oxygen Instrument . . . . . . . . . . . . . . . . .4-6
Figure 4-2 Calibration (Oxygen) Flow Chart . . . . . .4-8
Chapter5,
Warranty, aintenance,&Troubleshooting.5-1
MSA Portable Instrument Warranty . . . . . . . . . . . . . . . .5-1
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
!WARNIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Table 5-1. Troubleshooting uidelines . . . . . . . . . .5-3
Chapter6,
PerformanceSpecifications..............6-1
Table 6-1. Certifications . . . . . . . . . . . . . . . . . . . . .6-1
Table 6-2. Instrument Specifications . . . . . . . . . . .6-2
Table 6-3. Event Logging Specifications . . . . . . . .6-3
Chapter7,
ReplacementandAccessoryParts........7-1
Table -7-1. Replacement Parts List . . . . . . . . . . . .7-1
iii
1-1
Chapter1,
InstrumentSafetyandCertifications
The Altair Single as Detector is:
• For use by trained, qualified personnel
• For use as a warning device only and not for measuring specific
gas concentrations
• To be used when performing a hazard assessment to:
• Assess potential worker exposure to Specific toxic gases
for which a sensor is installed
• Oxygen-deficient or oxygen-rich atmospheres
NOTE: Although the Altair unit will detect up to 25% oxygen, all
Altair versions are not certified or classified for use in
atmospheres containing more than 21.0% oxygen
• Read and follow all instructions carefully.
• Do not use this detector to sample the instrument’s
specified gas in gases other than air.
• Perform an alarm function check and a bump test before
each day’s use. If the instrument fails either check, the
instrument must be taken out of service.
• Recheck response and alarm function if the instrument is
subjected to physical shock.
• The instrument is factory-sealed and contains no user
serviceable parts. Substitution of components may impair
intrinsic safety.
• This unit contains a lithium battery; dispose of according to
local regulations.
• Do not rely on the vibrating alarm in cold temperatures
(<0°C) as the vibrating alarm may cease to operate under
these conditions.
• Use only to detect a gas for which a sensor is installed.
• Do not block sensor.
• Do not use pressurized air to clean the sensor holes.
• All instrument readings and information must be interpreted
by someone trained and qualified in interpreting instrument
readings in relation to the specific environment, industrial
practice and exposure limitations.
!WARNING
1-2
INCORRECTUSEORFAILURETOFOLLOWTHISWARNING
CANRESULTINSERIOUSPERSONALINJURY
ORDEATH.
Certifications
The Altair Single as Detector meets applicable industry and
government standards as indicated on the instrument Approval label
and specified in TABLE 6-1.
Chapter2,
UsingtheAltairSingleGasDetector
ChangingAlarmSetpoints
NOTE: Alarm setpoints can only be changed manually during or before
activation. Once the instrument is activated, the Alarm setpoints
can be changed via the MSA FiveStar®LINKTM Software with IR
communications.
Figu e 2-2. Altai Display
Figu e 2-1. Altai Ove view
2-1
TochangeAlarmsetpointsbeforeactivation:
1. Press the "TEST" button once.
•"TEST" displays.
•. After approximately one second, all segments and the LED
activate.
• The horn, LEDs, and vibrator also activate
• The Software Version displays for three seconds
("CO", "H2S", or "O2").
2. Alarm Setpoints display the:
•LowAlarmSetpointfor three seconds
• LO and ALARM icons turn ON
a. To change the low alarm setpoint, press the TEST button
when "LO" "ALARM" displays:
• "LO" "ALARM" "SET" "?" displays.
b. Press and hold the TEST button to increment the low
alarm value.
c. Once the correct value displays, release the TEST button
and wait three seconds to continue.
•HighAlarmSetpointfor three seconds
• HI and ALARM icons turn ON
a. To change the high alarm setpoint, press the TEST button
when "HI" "ALARM" displays:
• "HI" "ALARM" "SET" "?" displays
b. Press and hold the TEST button to increment the high
alarm value.
c. Once the correct value displays, release the TEST button
and wait three seconds to continue.
3. Wait three seconds.
• the unit again turns OFF.
2-2
Figu e 2-3. Changing the Ala m Setpoints
2-3
Andere Handbücher für Altair
3
Inhaltsverzeichnis
Sprachen:
Andere MSA Sicherheitssensor Handbücher
MSA
MSA altair 5 Bedienungsanleitung
MSA
MSA Sirius Bedienungsanleitung
MSA
MSA ALTAIR 5X PID Bedienungsanleitung
MSA
MSA Ultima OPIR-5 Betriebsanleitung
MSA
MSA Sirius Bedienungsanleitung
MSA
MSA ICM 2000 Bedienungsanleitung
MSA
MSA Evotech Betriebsanleitung
MSA
MSA SOLARIS Bedienungsanleitung
MSA
MSA CutOff Bedienungsanleitung
MSA
MSA V-TEC PFL Bedienungsanleitung
MSA
MSA FireHawk M7XT ExtendAire II Gebrauchs- und Pflegehandbuch
MSA
MSA ExtendAire II Series Bedienungsanleitung
MSA
MSA ALTAIR5 Bedienungsanleitung
MSA
MSA ORION Bedienungsanleitung
MSA
MSA Dyna-Glide Bedienungsanleitung
MSA
MSA ALTAIR 5X Bedienungsanleitung
MSA
MSA ALTAIR PRO H2S Bedienungsanleitung
MSA
MSA altair 5 Technisches Handbuch
MSA
MSA Hip-Air Gebrauchsanweisung
MSA
MSA FL500 UV/IR Bedienungsanleitung
