MSTRONIC MSE PSE-SW3G Bedienungsanleitung

USER’S MANUAL

MSTRONIC CO., LTD.

MSE PSE-SW3G

3 Port PoE Switch & Extender

(Repeat Ethernet and PoE)

User’s Manual

MSE PSE-SW3G series

MSTRONIC CO., LTD.

1. General Information..............................................................

2. Hardware Description...........................................................

LED Indicators.......................................................................................

Power Wiring ........................................................................................

Ethernet Port Wiring..............................................................................

PD Port Wiring......................................................................................

Network Application……………………………………............................

3. Model Information...........................................................

4. Technical Specification........................................................

User’s Manual

MSE PSE-SW3G series

MSTRONIC CO., LTD.

1. General Information

The PoE (Power Over Ethernet) Switch family provide two 10M/100M/1000M TX ports with PoE

PSE function plus one 10M/100M/1000M TX up-link port with PoE PD function. It allow powered

from PoE power souring equipment (PSE) and deliver power to PoE powered device (PD), which is

compliant with IEEE802.3af and IEEE802.3at standard to receiver and deliver both of Ethernet data

and DC power through the traditional UTP or STP cable. The PoE Switch can extend Ethernet data

and DC power up to 200 meters.

This manual will help you install and maintain the PoE switch.

Installation of the PoE switch is very easy and you will begin to operate as soon as you are powered

up.

2. Hardware Description

*LED Indicator

There are 8 LEDs on the PoE switch to indicate the status of power and signal. The following

section describes the functions of each LED indicator.

Front panel detail

User’s Manual

MSE PSE-SW3G series

MSTRONIC CO., LTD.

*POWER LED

LED

STATUS

Description

Power

Green

LED ON when power input (DC IN on

rear panel or Port UPLINK on front

panel) has valid power supplied.

Red

The indicator only been used on

PSE-SW3G11CN, LED ON when the

following warning condition happened.

*Power input under voltage (Vin<10V)

*Power input over voltage (Vin>59V)

*PoE over current (2A/per port)

the indicator is unused on

PSE-SW3G44DN

Off No power supplied.

*SWITCH LED (the right indicator on RJ45)

LED STATUS Description

P1~P3

Link/Act

Green

A network device is detected (1000Mbps),

but no communication activity is detected.

Green

Blinking

This port is transmitting to, or receiving

package from another device at 1000Mbps.

Yellow A network device is detected (10Mbps or

100Mbps), but no communication activity

is detected.

Yellow

Blinking

This port is transmitting to, or receiving

package from another device at 10Mbps or

100Mbps.

Off No device is detected.

User’s Manual

MSE PSE-SW3G series

MSTRONIC CO., LTD.

*PoE LED (the left indicator on RJ45)

P1~P2

PoE

Yellow

A valid Powered Device (PD) is detected

and delivering power on this port.

Off

No PD is detected on this port.

PoE

Yellow

Powered via all 4 data pairs.

Yellow

Blanking

Powered via 2 data pairs. (1,2,3,6 or 4,5,7,8

are all acceptable).

Off No power is detected on this port.

*Power wiring

The PoE switch family includes 2 models, be used for 2 different ranges of input voltage as,

full range voltage (10 to 57VDC) (P/N: PSE-SW3G11CN)

48VDC typical (40 to 57VDC) (P/N: PSE-SW3G44DN)

All of the PoE switches allow powered by another PoE source (42.5~57VDC) on port 3 (UPLINK).

For PoE operation, make sure your power supply may offer at least 40W for 2x 802.3af PoE port, or

80W for 2x 802.3at PoE port.

If powered on rear terminal, please make sure the input current don’t over 10A, if powered on port

3, make sure the input current don’t over 2Amp.

The port 1&2 will deliver DC power over the Ethernet cable, the connection as:

* Data pair A on line 1 and 2

* Data pair B on line 3 and 6

* Data pair C plus V+ on line 4 and 5

* Data pair D plus V- on line 7 and 8

User’s Manual

MSE PSE-SW3G series

MSTRONIC CO., LTD.

The port 3 may get DC power over the Ethernet cable, the connection as:

* Data pair A plus V+ /V- on line 1 and 2

* Data pair B plus V-/V+ on line 3 and 6

* Data pair C plus V+/V- on line 4 and 5

* Data pair D plus V-/V+ on line 7 and 8

The terminal block on rear panel should be wiring as:

*For PSE-SW3G44DN

The input voltage must be in the range of 40 to 57VDC if running for 802.3af operation.

The input voltage must be in the range of 50 to 57VDC if running for 802.3at operation.

If the PSE-SW3G44DN is not powered in above designated input voltage, it will only functioning

as an Ethernet switch without PoE output.

User’s Manual

MSE PSE-SW3G series

MSTRONIC CO., LTD.

Model Input Voltage

(REAR) Input Voltage

(Port 3) Output voltage 802.3af/at

Isolated

PSE-SW3G11CN

10-57VDC No input

10-57VDC

(As input voltage)

(non-regulated) No No

No input 42.5-57VDC 42.5-57VDC

(non-regulated) No No

10-57VDC 42.5-57VDC

Higher voltage

output

(REAR or Port 3)

No No

PSE-SW3G44DN

40-57VDC No input 40-57VDC

(non-regulated) Yes No

No input 42.5-57VDC 42.5-57VDC

(non-regulated) Yes No

40-57VDC 42.5-57VDC

Higher voltage

output

(REAR or Port 3)

Yes No

You could use the PSE-SW3G series with our adaptor products as the below: (OPTION)

MS-A150-18-1 MS-A150-24-1 MS-A150-48-1

Maximum output 18VDC/7.5A 24VDC/6.25A 48VDC/3.125A

Related model PSE-SW3G11CN

PSE-SW3G11CN

PSE-SW3G44DN

User’s Manual

MSE PSE-SW3G series

MSTRONIC CO., LTD.

*Ethernet Port Wiring

The PoE switch family supports one RJ-45 uplink (port 3 with PoE PD) and two RJ-45 ports (port

1&2 with PoE PSE) with automatic MDI/MDI-X crossover, auto-sense the speed and duplex for

10Base-T, 100Base-TX or 1000Base-T connection. Automatic MDI/MDI-X crossover allows you

to connect to other devices (switches, hubs, or workstations etc.), without regard to using

straight-through or crossover cabling.

Port 1 & 2 provides Power over Ethernet function that delivers DC power through the data pairs C

& D (pair 4,5 and pair7,8) to the PD. Port 3 provides Power Device (PD) function that receive

power from 4 pairs or 2 pairs Ethernet cable.

The following tables describe the wiring diagram of straight-through and crossover cabling. That

crossover cables simply cross-connect the transmit lines at each end to the receive lines at the

opposite end.

Straight-through Cabling

Pin 1

Pin 2

Pin 3

Pin 6

Pin 4

Pin 5

Pin 7

Pin 8

User’s Manual

MSE PSE-SW3G series

MSTRONIC CO., LTD.

Cross-over Cabling

Pin 1

Pin 3

Pin 2

Pin 6

Pin 3

Pin 1

Pin 6

Pin 2

Pin 4

Pin 7

Pin 5

Pin 8

Pin 7

Pin 4

Pin 8

Connect an Ethernet cable into any switch port and connect the other side to your

attached device. The Link/Act LED (green or yellow) will light up when the cable is correctly

connected. Refer to the LED Indicator section for descriptions of each LED indicator.

If a port LED is off, go back and check for connectivity problems between that port and the network

device connected.

The maximum cable length for 10/100/1000BaseT with Cat 5 twisted pair cables is typically 100m

(328 ft.).

User’s Manual

MSE PSE-SW3G series

MSTRONIC CO., LTD.

*PD Port Wiring

Port 1 & 2 provide PoE inject function with maximum 35W ability to power up the powered device

use the straight-through or cross-over Ethernet cable.

The PoE switch follows the IEEE802.3af Alternative B mode connector assignment. The following

table shows pin assignment of alternative A and B for the Power Source Equipment.

Conductor Alternative A

(MDI-X) Alternative A

(MDI) Alternative B

(All)

1Negative Vport Positive Vport

2 Negative Vport Positive Vport

3 Positive Vport Negative port

4 Positive Vport

5 Positive Vport

6 Positive Vport NegativenVport

7 Negative Vport

8 Negative Vport

Be sure the twisted pair cable is bound with the standard RJ-45 pin, especially the pin 4, 5, 7 and 8.

If the RJ-45 is bound with the wrong pin number, PoE switch will not recognize the PD and won’t

deliver DC power to PD. The yellow PoE LED will light up when the cable is correctly connected.

Refer to the LED Indicator section for descriptions of each LED indicator. If a port LED is off, go

back and check for connectivity problems between that port and the network device connected.

Andere Handbücher für MSE PSE-SW3G

Inhaltsverzeichnis

Andere MSTRONIC Extender Handbücher

MSTRONIC

MSTRONIC PSE-SW3B44DB Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung