MSTRONIC PSE-SW5F-ST Bedienungsanleitung

PSE-SW5F-ST

PSE-SW5F-SC

PSE-SW5F-SFP

USER’S MANUAL

MSTRONIC CO., LTD.

MSE PSE-SW5F Series

Power Source Equipment

(Power over Ethernet Switch)

User’s Manual

MSE PSE-SW5F-ST/-SC/-SFP

MSTRONIC CO., LTD.

1. General Information..............................................................

2. Hardware Description...........................................................

LED Indicators......................................................................................

Power Wiring……………………………………………………………….

Ethernet Port Wiring……………………………………………………….

Fiber Port Wiring...................................................................................

PD Port Wiring…………………………………………………………….

3.Model Information........................................................

4. Technical Specification........................................................

User’s Manual

MSE PSE-SW5F-ST/-SC/-SFP

MSTRONIC CO., LTD.

1. General Information

The PoE (Power Over Ethernet) Switch supports four Fast Ethernet ports with PoE injector plus one

100Base-FX up-link port. The switch provides Power over Ethernet functions to deliver 35Watts of

power budget per port to a powered device(PD), which is in compliance with IEEE802.3af/at

standard to deliver both Ethernet data and DC48V power through the traditional UTP or STP cable

to a PD.

This manual will help you install and maintain the PoE switch. Installation of the PoE

switch is very easy and it will begin to operate as soon as you have powered it up.

2. Hardware Description

*LED Indicator

There are 10 LEDs on the PoE switch to indicate the power and operational status. The following

section describes the functions of each LED indicator.

Front panel detail

For PSE-SW5-ST:

PoE Link/Act

Indicator Indicator

For PSE-SW5-SC:

PoE Link/Act

Indicator Indicator

User’s Manual

MSE PSE-SW5F-ST/-SC/-SFP

MSTRONIC CO., LTD.

For PSE-SW5-SFP:

PoE Link/Act

Indicator Indicator

*POWER Indicator

LED

STATUS

Description

Power

(PWR)

Green

LED ON if power input has valid power

apply.

Red

LED ON if the following condition

happens.

*Power input under voltage (Vin<10V)

*Power input over voltage (Vin>59V)

*PoE over current(2.5A/per port)

The indicator is used in current mode

only.

Off No power in DC input

LINK/ACT

User’s Manual

MSE PSE-SW5F-ST/-SC/-SFP

MSTRONIC CO., LTD.

*SWITCH Indicator (the right LED of RJ-45)

LED STATUS Description

P1~P5

Link/Act

Green

A network device is detected, but no

communication activity is detected.

Blinking

@43ms

This port is transmitting to, or receiving

package from another device at 100Mbps.

Blinking

@120ms

This port is transmitting to, or receiving

package from another device at 10Mbps.

Off No device is detected.

*PoE Indicator (the left LED of RJ-45)

LED STATUS Description

P1~P4

PoE

Yellow

A valid Powered Device(PD) is detected

and delivering power on this port.

Off No PD is detected on this port.

*Power wiring

The PoE switch family includes 3 models, be used for 3 different ranges of input voltage as,

Current mode full range voltage (10 to 57VDC)

24V-802.3at mode 24VDC typical(12 to 36VDC)

48V-802.3at mode 48VDC typical(40 to 57VDC)

In current mode, please make sure the input current don’t over 10Aand make sure the input current

don’t over 2Amp.

User’s Manual

MSE PSE-SW5F-ST/-SC/-SFP

MSTRONIC CO., LTD.

For PoE (PSE) operation, the input voltage must be in the range of -42 to -60 VDC. Otherwise, the

switch will function only as an Ethernet switch but will not provide any PoE power output. For PoE

operation, make sure your 48 VDC supply is rated for at least 75 Watts for 4x 802.3af PoE port, or

150W for 4x 802.3at PoE port, plus some overhead for the switch.

The PoE PSE ports will deliver DC power over the spare pairs as the connection:

* TX on lines 1 and 2

* RX on lines 3 and 6

* V+ on line 4 and 5

* V- on line 7 and 8

Rear panel terminal block wiring detail:

*Ethernet Port Wiring

The PoE Switch supports Port 1 to Port 4 with automatic MDI/MDI-X crossover, autosense of the

speed and duplex for 10Base-T or 100Base-TX connections. Automatic MDI/MDI-X crossover

allows you to connect to other devices (switches, hubs, or workstations etc..), without regard to

using straight-through or crossover cabling.

Port 1 to port 4 also provides Power over Ethernet function which delivers DC48V power through

the spare pairs (pair 4,5 and pair7,8) to the PD.

User’s Manual

MSE PSE-SW5F-ST/-SC/-SFP

MSTRONIC CO., LTD.

The following tables depict the wiring diagram of straight-through and crossover cabling. The

crossover cables simply cross-connect the transmit lines at each end to the receive lines at the

opposite end.

Straight-through Cabling

Pin 1

Pin2

Pin 2

Pin3

Pin 3

Pin6

Cross-over Cabling

Pin 1

Pin 3

Pin 2

Pin 6

Pin 3

Pin 1

Pin 6

Pin 2

User’s Manual

MSE PSE-SW5F-ST/-SC/-SFP

MSTRONIC CO., LTD.

Connect an Ethernet cable into any switch port and connect the other side to your attached device.

The green Link/Act LED will light up when the cable is correctly connected. Refer to the LED

indicator section for descriptions of each LED indicator.

If a port LED is off, go back and check for connectivity problems between that port and the network

device it is connected to.

The maximum cable length for 10/100BaseT with Cat 5 twisted pair cables is

typically 100 meters (328 ft.).

Fiber port wiring

The PoE switch(fiber mode) has one 100 Mbps (100Base-FX) multi-mode or single-mode fiber port.

The maximum segment length is dependant upon the type of fiber optic transceiver installed in the

switch. Refer to the technical specifications for details. Or contact a sales agent for the available

fiber optic transceivers(Model NO.:MSE PSE-SW5F-ST or PSE-SW5F-SC or PSE-SW5F-SFP).

The automatic MDI/MDI-X crossover function does not apply to fiber connections.

To connect the

fiber optic port on one switch to the fiber optic port of another switch, simply cross-connect the

transmitter at each end to the receiver at the opposite end as illustrated in the figure below.

The corresponding ACT/LNK LED will be ON state when you have made a proper connection.

Fiber cable wiring (SC to SC):

User’s Manual

MSE PSE-SW5F-ST/-SC/-SFP

MSTRONIC CO., LTD.

*PD Port Wiring

Port 1 to port 4 provides PoE inject functionality with a maximum 35W ability to power up the

powered device using the straight-through or cross-over Ethernet cable.

The PoE switch follows the IEEE802.3af Alternative B mode connector assignment. The following

table shows pin assignments of alternative A and B for the Power Source Equipment.

Conductor

Alternative A

(MDI-X) Alternative A

(MDI)

Alternative B

(All)

1Negative Vport Positive Vport

2 Negative Vport Positive Vport

3 Positive Vport Negative port

4 Positive Vport

5 Positive Vport

6 Positive Vport Negative Vport

7 Negative Vport

8 Negative Vport

Be sure the twisted pair cable is bound with the standard RJ-45 pin, especially pins 4, 5, 7 and 8.

If the RJ-45 is bound with the wrong pin number, the PoE switch will not recognize the PD and

won’t deliver DC48V power to PD. The yellow PoE LED will light up when the cable is correctly

connected. Refer to the LED Indicator section for descriptions of each LED indicator. If a port

LED flashes, go back and check for connectivity problems between that port and the network

device it is connected to.

User’s Manual

MSE PSE-SW5F-ST/-SC/-SFP

MSTRONIC CO., LTD.

3. Model Information

Model

Input Voltage

Output voltage

802.3af/at

PSE-SW5F-ST-S

PSE-SW5F-SC-S

PSE-SW5F-SFP-S

(current mode)

10-57VDC 10-57VDC

(non-regulated) No

PSE-SW5F-ST24

PSE-SW5F-SC24

PSE-SW5F-SFP24

(24V-802.3at mode)

12-36VDC 56VDC

(regulated) Yes

PSE-SW5F-ST48

PSE-SW5F-SC48

PSE-SW5F-SFP48

(48V-802.3at mode)

40-57VDC 40-57VDC

(non-regulated) Yes

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MSTRONIC Stromversorgung Handbücher

MSTRONIC

MSTRONIC MSR-1231 Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung