MSTRONIC PSE-SW5G15B4HM Bedienungsanleitung

USER’S MANUAL

MSTRONIC CO., LTD.

PSE-SW5G15B4HM

5 Port PoE Switch & Extender

(Repeat Ethernet and PoE)

User’s Manual PSE-SW5G15B HM

MSTRONIC CO., LTD.

1. Genera Information

The fanless PSE-SW5G PoE (Power Over Ethernet) Extender provides four 1 M/1 M/1 M TX

ports with PoE PSE function plus one 1 M/1 M/1 M TX up-link port with PoE PD function. It

accepts power from PoE power sourcing equipment (PSE) and delivers power to PoE powered

device (PD), which are compliant with IEEE8 2.3af and IEEE8 2.3at standard to receive and

deliver both Ethernet data and DC power through the traditional UTP or STP cable. The PoE

Switch can extend Ethernet data and DC power up to 2 meters when used as a PoE repeater.

2. Hardware Description

*LED Indicator

There are 12 LEDs on the PoE switch to indicate the status of power and signal. The following

section describes the functions of each LED indicator.

Front panel detail

*POWER LED

LED STATUS Description

Power

Green

LED ON when power input (DC IN on rear

panel or UPLINK on front panel) has valid

power supplied.

Off No power supplied.

User’s Manual PSE-SW5G15B HM

MSTRONIC CO., LTD.

*SWITCH LED (the right indicator on RJ45)

LED STATUS Description

P1~P5

Link/Act

Green

A network device is detected (1 Mbps), but

no communication activity is detected.

Green

Blinking

This port is transmitting to, or receiving

package from another device at 1 Mbps.

Yellow A network device is detected (1 Mbps or

1 Mbps), but no communication activity is

detected.

Yellow

Blinking

This port is transmitting to, or receiving

package from another device at 1 Mbps or

1 Mbps.

Off No device is detected.

*PoE LED (the left indicator on RJ45)

P1~P4

PoE Out

Yellow

A valid Powered Device (PD) is detected and

delivering power on this port.

Off

No PD is detected on this port.

UPLINK (P5)

PoE In

Yellow

Powered from another PoE,

Powered via all 4 pairs.

Yellow

Blinking

Powered via 2 pairs, data pairs (pin 1,2,3,6) or

spare pairs (pin 4,5,7,8) are all acceptable.

Off No power is detected on this port.

User’s Manual PSE-SW5G15B HM

MSTRONIC CO., LTD.

*Power wiring

The PoE switch allows to be powered by another PoE source on port 5 (UPLINK) and/or on rear

terminal,

If powered on port 5 (UPLINK) as a PoE repeater, the PoE input must be 44~57VDC, the input

current should not be over 2Amp.

Please note the green connector is capable of 12A max. If more current is required, use 4 pin DIN

connector for up to 15A.

Model Input Voltage

(REAR)

Input Voltage

(Port 5) Output voltage

PSE-SW5G15B4HM

11-6 VDC No input 56VDC

(regulated)

No input 44-57VDC 44-57VDC

(non-regulated)

11-6 VDC 44-57VDC 56VDC

(regulated)

For PoE operation, total output may up to 35W (8 2.3at) x 4.

Ports 1~4 will deliver DC power over the Ethernet cable as detailed below:

* Data pair A on line 1 and 2

* Data pair B on line 3 and 6

* Data pair C plus V+ on line 4 and 5

* Data pair D plus V- on line 7 and 8

Port 5 (UPLINK) may receive DC power over the Ethernet cable, as detailed below:

* Data pair A plus V+ /V- on line 1 and 2

* Data pair B plus V-/V+ on line 3 and 6

* Data pair C plus V+/V- on line 4 and 5

* Data pair D plus V-/V+ on line 7 and 8

The terminal block on the rear panel should be wired as detailed below, if the input voltage is in

User’s Manual PSE-SW5G15B HM

MSTRONIC CO., LTD.

11~16VDC, cause of heavy input current, please make sure the 4 input pins are all used.

The DIN-4P connector on the rear panel can be also used for power input, you can use an AC/DC

adapter with DIN-4P connector directly, recommend adaptor MS-18 -56. (OPTION)

When you connect both green connector and DIN 4P connector, the higher voltage source takes

priority.

*Ethernet Port Wiring

The PoE switch family supports one RJ-45 uplink (port 5 with PoE PD) and four RJ-45 ports (port

1~4 with PoE PSE) with automatic MDI/MDI-X crossover, auto-sense for speed and duplex for

1 Base-T, 1 Base-TX or 1 Base-T connection. Automatic MDI/MDI-X crossover allows you

to connect to other devices (switches, hubs, or workstations etc.), without regard to using

straight-through or crossover cabling.

Port 1 to 4 provides Power over Ethernet function that delivers DC power through the data pairs C

& D (pin 4,5 and pin 7,8) (mode B) to the PD. Port 5 provides PD function that receives power

from 4 pairs or 2 pairs PoE.

The following tables describe the wiring diagram of straight-through and crossover cabling. The

crossover cables simply cross-connect the transmit lines at each end to the receive lines at the

opposite end.

User’s Manual PSE-SW5G15B HM

MSTRONIC CO., LTD.

Straight-through Cabling

Pin 1 Pin 1

Pin 2 Pin 2

Pin 3 Pin 3

Pin 6 Pin 6

Pin 4 Pin 4

Pin 5 Pin 5

Pin 7 Pin 7

Pin 8 Pin 8

Cross-over Cabling

Pin 1 Pin 3

Pin 2 Pin 6

Pin 3 Pin 1

Pin 6 Pin 2

Pin 4 Pin 7

Pin 5 Pin 8

Pin 7 Pin 4

Pin 8 Pin 5

Connect an Ethernet cable into any switch port and connect the other side to your

attached device. The Link/Act LED (green or yellow) will light up when the cable is correctly

connected. Refer to the LED Indicator section for descriptions of each LED indicator.

If a port LED is off, go back and check for connectivity problems between that port and the network

device connected.

The maximum cable length for 1 /1 /1 BaseT with Cat 5 twisted pair cables is typically 1 m

(328 ft.).

User’s Manual PSE-SW5G15B HM

MSTRONIC CO., LTD.

*PD Port Wiring

Port 1 to 4 provides PoE injection function with maximum 35W ability to power up the powered

device using the straight-through or cross-over Ethernet cable.

The PoE switch follows the IEEE8 2.3af/at Alternative B mode connector assignment. The

following table shows pin assignment of alternative A and/or B for the Power Source Equipment.

Conductor Alternative A

(MDI-X)

Alternative A

(MDI)

Alternative

(All)

1 Negative Vport Positive Vport

2 Negative Vport Positive Vport

3 Positive Vport Negative port

4 Positive Vport

5 Positive Vport

6 Positive Vport NegativeVport

7 Negative Vport

8 Negative Vport

Be sure the twisted pair cable is bound with the standard RJ-45 pin, especially the pins 4, 5, 7 and 8.

If the RJ-45 is bound with the wrong pin number, the PoE switch will not recognize the PD and

won’t deliver DC power to the PD. The yellow PoE LED will light up when the cable is correctly

connected. Refer to the LED Indicator section for descriptions of each LED indicator. If a port

LED is off, go back and check for connectivity problems between that port and the network device

connected.

User’s Manual PSE-SW5G15B HM

MSTRONIC CO., LTD.

*Network App ication

The PoE Switch can receive power from a PoE midspan and provide power to the PD which

follows the IEEE 8 2.3af/at standard in the network. The PoE Switch can be installed as a

PoE+Ethernet repeater to extend Ethernet to 2 meters. The following figure is an example of a

network application for the PoE Extender.

User’s Manual PSE-SW5G15B HM

MSTRONIC CO., LTD.

3. Technica Specifications

Standards IEEE8 2.3/IEEE8 2.3u standards/IEEE8 2.3ab (1

base-T/1 base-TX/1 base-T)

Ports 5 ports with PoE (4 PSE & 1 PD), support auto-crossover &

auto-polarity

Transmission speed 1 Mbps (1 base-T).1 Mbps (1 base-TX), 1 Mbps(1 base-T)

Auto-negotiation

Switch technology store-and-forward

Protocols CSMA/CD

Flow control IEEE8 2.3x (full-duplex), back pressure (half-duplex)

Data transmission rate 1488 pps for1 base-T, 1488 pps for 1 base-T, 1488 pps for

1 base-T

Address table 2K MAC address table, self-learning

Connect RJ-45

PoE port Port 1-4, PSE auto power management

Pin assignment:

data pair A (1,2),

data pair B (3,6),

data pair C plus V+(4,5),

data pair D plus V-(7,8)

Port 5, 4 pairs PD

Maximum PoE power Port 1-4: IEEE8 2.3at – 35W/port

Total power – 140W

User’s Manual PSE-SW5G15B HM

MSTRONIC CO., LTD.

Port 5: 9 W (8 2.3at 2 event classification) INPUT

Current limited – 2A

PSE disconnect mode DC disconnect

PoE auto detection IEEE8 2.3af & IEEE8 2.3at (2 event classification signaling)

PoE protection Over-temperature, over-current, over/under voltage

LEDs *Link/Activity (Green ON/ Green Blinking @1 Mbps,

Yellow/Yellow Blinking @1 M/1 Mbps)

*PoE (Yellow) port 1-4 ON - PD detect

Port 5 ON – 4 pair power, Blinking-2 pair power

*POWER Green-normal, Red-alarm

Power input PoE source on Port 5 (UPLINK), and/or optional DC power supply on

rear terminal. It with input low voltage protection, if input voltage

lower than 9.4V, the unit will be shut down.

Power consumption less than 5W when without PD loading

Input PSE-SW5G15B4HM

12V .23A/3.9W

24V .17A/2.7W

Power efficiency 85% at full load (@24V typical)

Operating temperature - 0℃~ +70℃

Operation humidity 9 % relative humidity, non-condensing with conformal coating

Storage temperature - 0℃~+85℃

Dimension 4 mm(H)x139mm(W)x147mm(D) DIN RAIL Mountable

Inhaltsverzeichnis

Andere MSTRONIC Schalten Handbücher

MSTRONIC

MSTRONIC PSE-SW8 series Bedienungsanleitung

MSTRONIC

MSTRONIC PSE-SW8G44D0++ Bedienungsanleitung

MSTRONIC

MSTRONIC PSE-SW8 series Bedienungsanleitung

MSTRONIC

MSTRONIC PSE-SW5G-25 4 Series Bedienungsanleitung

MSTRONIC

MSTRONIC PSE-SW5G25B4-IP66 Bedienungsanleitung

MSTRONIC

MSTRONIC MSE PSE-SSW5 Series Bedienungsanleitung

MSTRONIC

MSTRONIC PSE-SW5B15DBHM-IP66 Bedienungsanleitung

MSTRONIC

MSTRONIC PSE-SW5G-25B4HM Bedienungsanleitung

MSTRONIC

MSTRONIC MSE PSE-SW3G Bedienungsanleitung

MSTRONIC

MSTRONIC PSE-SW5B44DB Bedienungsanleitung

MSTRONIC

MSTRONIC PSE-SW3B25D0H Bedienungsanleitung

MSTRONIC

MSTRONIC PSE-SW8G44A4 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung