MTS Systems Exceed 40 Series Betriebsanleitung
Manual Title
Additional Information
be certain.
Site Preparation Guide
MTS Exceed™ Series 40
100-303-149 A
MTS Exceed™ Series 40 Site Preparation Guide
2
Copyright information
© 2013 MTS Systems Corporation. All rights reserved.
Trademark information
MTS is a registered trademarks and MTS Ex eed is a trademark of MTS Systems
Corporation. These trademarks may be prote ted in other ountries.
Proprietary information
Software use and li ense is governed by MTS’ End User Li ense Agreement
whi h defines all rights retained by MTS and granted to the End User. All
Software is proprietary, onfidential, and owned by MTS Systems Corporation
and annot be opied, reprodu ed, disassembled, de ompiled, reverse
engineered, or distributed without express written onsent of MTS.
Software alidation and
erification
MTS software is developed using established quality pra ti es in a ordan e
with the requirements detailed in the ISO 9001 standards. Be ause MTS-
authored software is delivered in binary format, it is not user a essible. This
software will not hange over time. Many releases are written to be ba kwards
ompatible, reating another form of verifi ation.
The status and validity of MTS’ operating software is also he ked during
system verifi ation and routine alibration of MTS hardware. These ontrolled
alibration pro esses ompare the final test results after statisti al analysis
against the predi ted response of the alibration standards. With these established
methods, MTS assures its ustomers that MTS produ ts meet MTS’ exa ting
quality standards when initially installed and will ontinue to perform as intended
over time.
MTS Exceed™ Series 40 Site Preparation Guide Contents
3
Contents
Introduction 5
Responsibilities 7
Customer’s Responsibilities 8
MTS’ Responsibilities 9
Site Preparation 11
System Specifications 17
Pa kaging Dimensions and Weight 18
Load Frame Dimensions and Weight 19
Environmental Requirements 20
Ele tri al Power Requirements 21
Additional Considerations 23
Load Unit Considerations 24
Computer Console Considerations 24
When You Get Your System 25
Site Requirements Chec list 27
Lift and Move Instructions 29
Moving E42 Single-Column Frames 30
Moving E43 Double-Column Frames 33
Moving E44 and E45(Standing position) Frames 35
Moving E45(prone position) Frames 41
MTS Exceed™ Series 40 Site Preparation Guide Introduction
5
Introduction
MTS Ex eed Ele trome hani al Material Test Systems are designed to operate in
a laboratory or light industry environment. To get the maximum intended use of
the system, it is re ommended that areful onsideration be given to planning its
installation. This in ludes:
•The types of testing that will be performed.
•The building fa ilities requirements for power, ooling water, air
onditioning, eiling height, floor loading, and so on.
•Contra t servi es, su h as riggers and moving equipment, to transport the
system omponents within the fa ility.
•Support personnel that might be required during installation of the system.
In addition to the test system requirements, ea h test appli ation also has its own
requirements. Therefore, it is re ommended that overall planning be onsidered
as early as possible. Preparation for and setup of the major system omponents
are your responsibility. This guide will help answer most of your questions about
the physi al hara teristi s and requirements of your system.
MTS Exceed™ Series 40 Site Preparation Guide Responsibilities
7
Responsibilities
This se tion details the responsibilities of both the ustomer and MTS to ensure
that the proposed testing area is suitable for the installation and operation of the
test system.
Contents
Customer’s Responsibilities 8
MTS’ Responsibilities
MTS Exceed™ Series 40 Site Preparation Guide
8
Customer’s Responsibilities
Responsibilities
Customer’s Responsibilities
It is the ustomer’s responsibility to ensure that all required support servi es are
available, and that all ne essary he ks are made prior to installing the test
system.These servi es and he ks are des ribed below.
Site Preparation
Proper site preparation is imperative so that the test system operates in
a ordan e with its spe ifi ations and provides a urate test results. The
ustomer must ensure that the site requirements are satisfied prior to s heduling
the installation appointment.
Handling and Transporting
Unless spe ifi ally arranged otherwise, it is the ustomer’s responsibility to
arrange the off-loading, unpa king and moving of the test system to the final site
lo ation. For details on handling and transporting your system to its final
lo ation, see “Lift and Move Instru tions” on page 29.
Upon spe ial arrangements, an MTS servi e engineer an supervise the off-
loading and transportation of the load frame to its final site. Conta t the MTS
Servi e department or your lo al MTS offi e for additional information on this
servi e.
It is the ustomer’s responsibility to provide slings and hoist rings. Slings and
hoist rings must onform to lo al odes and regulations and be sized orre tly to
support the weight of the load frame. Weights and thread sizes are provided in
this manual.
Insurance and Safety
Under MTS’ standard ontra t, the shipping terms are Ex-Works (or FOB
Fa tory), meaning ownership and liability for the test system transfers to the
ustomer at MTS’ loading do k. Unless other shipping terms are spe ified in a
pur hase order, whi h MTS does not dispute, the Ex-Works shipping terms
apply. Under these terms, the ustomer is responsible for se uring the appli able
transit insuran e on the shipment and arranging safe transport to the final
destination. Arrangements an be made through MTS to se ure insuran e
overage and shipping, at the ustomer’s expense.
When transporting a load frame within your own premises, you are responsible
for its safe transport. Upon spe ial arrangements, an MTS servi e engineer an
supervise the transportation to the load frame’s final site. Conta t the MTS
Servi e department or your lo al MTS offi e for additional information on this
servi e.
MTS’ Responsibilities
MTS Exceed™ Series 40 Site Preparation Guide Responsibilities
9
MTS’ Responsibilities
MTS’ standard ontra t requires MTS to provide the ne essary servi es to ensure
that your test system operates a urately. These servi es are des ribed below.
Additional servi es and equipment may be negotiated with MTS, but these
additional servi es must be mutually agreed upon and spe ifi ally des ribed in
your pur hase order.
Insurance
Under MTS’ standard ontra t, the shipping terms are Ex-Works (or FOB
Fa tory), meaning ownership and liability for the test system transfers to the
ustomer at MTS’s loading do k. Unless other shipping terms are spe ified in a
pur hase order, whi h MTS does not dispute, the Ex-Works shipping terms
apply. Under these terms, MTS is responsible for insuran e overage while the
test system is in the fa tory until it rea hes the loading do k for shipping.
Installation
When the site lo ation is prepared and all the omponents are on site, MTS is
responsible for the omplete installation of the load frame, its omponents, and
any additional a essories that may have been pur hased. The ustomer must not
make any attempt to install the load frame without an MTS servi e representative
present.
Initial Operation
On e the installation is omplete, MTS performs an initial operation of the load
frame and a alibration he k to ensure that it is working properly and measuring
a urately. MTS also performs a ustomer demonstration that briefly des ribes
how to operate the system.
Documentation
MTS provides all the do umentation required to operate the system, in luding
manuals for the load frame and any required software appli ations.
Additional opies are available and an be ordered through the MTS Sales
department.
Andere Handbücher für Exceed 40 Series
1
Dieses Handbuch passt für folgende Modelle
17
Inhaltsverzeichnis
Andere MTS Systems Prüfgeräte Handbücher
MTS Systems
MTS Systems Landmark 370 Series Bedienungsanleitung
MTS Systems
MTS Systems 318 Series Bedienungsanleitung
MTS Systems
MTS Systems MA2000 Series Bedienungsanleitung
MTS Systems
MTS Systems FlexTest SE Bedienungs- und Montageanleitung
MTS Systems
MTS Systems Landmark 370 Series Bedienungsanleitung
MTS Systems
MTS Systems Exceed 22 Series Bedienungsanleitung
MTS Systems
MTS Systems Exceed 40 Series Bedienungsanleitung
MTS Systems
MTS Systems Exceed 22 Series Bedienungsanleitung
Beliebte Prüfgeräte Handbücher anderer Marken
SMART
SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies BERT Serial Bedienungsanleitung
Agilent Technologies
Agilent Technologies N3280A Bedienungsanleitung
Vernier
Vernier Go Direct Voltage Bedienungsanleitung
Lifeloc
Lifeloc R.A.D.A.R. Bedienungsanleitung
Fluke
Fluke T5-600 Bedienungs- und Montageanleitung
PCB Piezotronics
PCB Piezotronics 8159-0112A Bedienungsanleitung
BW Technologies
BW Technologies MicroDock II Bedienungsanleitung
Sun Nuclear
Sun Nuclear 1027 Bedienungsanleitung
Biomark
Biomark HPR LITE READER Bedienungsanleitung
Hioki
Hioki 3169-20 Bedienungsanleitung
Ashcroft
Ashcroft ATE-100 Bedienungsanleitung