MTX RZRXP-10 Bedienungsanleitung
MTX.COM
OWNER’S MANUAL
RZRXP-10
POLARIS®RZR®AMPLIFIED SUBWOOFER ENCLOSURE
MTX.COM
2
IMPORTANT NOTICE
If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support
at 1-800-225-5689.
When connecting power and ground wires ensure that the red power wire is fused at the point
where it is connected to the vehicle’s battery. Failure to do so can result in damage to the vehicle if a
short circuit develops between the vehicle connection point and the product.
PRODUCT INFORMATION
Model #
Serial #
Dealer’s Name
Date of Purchase
IN THE BOX
• RZRXP-10AmpliedSubwooferEnclosure
• EBCandEBCExtensionWire
• Mounting Hardware
(1)1"T30TorxScrew
(2)1.5"T30TorxScrews
ADDITIONAL ACCESSORIES NEEDED AND NOT INCLUDED
MTX recommends using StreetWires PS1K-10 amp kit which includes the following:
• PowerandGroundWiretoRuntotheBattery
• 20AATCFuseHolderandFuse
• AccessoryConnectionWire
• RCACablestoConnecttotheSource
INSTALLATION TOOLS
The following is a list of suggested tools needed for installation:
• Torx-T40
• Torx-T30
• Torx-T25
• 10mm Wrench or Socket
• Razor Knife
INTRODUCTION
ThankyouforpurchasingtheMTXAudioampliedsubwooferenclosuredesignedforthePolaris®
RZR®.TheeasytoinstallsubwooferistheperfectdirecttbasssolutionforyourPolaris®RZR®.
CongratulationsandenjoytheultimateaudioexperiencewithMTX!
FITS THE FOLLOWING VEHICLES
• RZR®XP/XP41000(2014andUp)
• RZR®XP/XP4TURBO(2016andUp)
• RZR®900/900S/1000S(2015andUp)
• RZR®4900EPS(2015andUp)
NOTE:Willnottonvehicleswiththeaddedheateraccessory.
MTX.COM 3
FEATURES
• 10"All-WeatherAmpliedSubwooferEnclosure
• Integrated250-WattRMS/500-WattPeakPowerAmplier
• IntegratedPowerandGroundConnections
• LowLevelInputwithExternalGainControl
• DashMountBassControlKnob(Included)
• MountsUnderneathDashboard-DirectFit,NoDrillingRequired
SPECIFICATIONS
• RMS Power Handling: 250-Watts
• Peak Power Handling: 500-Watts
• FrequencyResponse:34Hz-120Hz
MTX.COM
4
INSTALLATION
Step 1 - Release the two quick locks to remove the hood from the vehicle.
Step 2 - Lift up the hood and slide towards the front of the vehicle.
Step3-Removethetwo(2)T40screwsholdingdownthetopdashcover.
MTX.COM 5
Step4-Liftandpullbackthetopdashcovertoreleasetheclipsholdingitinplace.Unplugthegauge
and switches making sure not to damage the vehicle and ignition wiring. Make note to remember
whatconnectorisassociatedwitheachspecicswitch.
Step5-RemovetheTorxheadscrewfromthedashpocketbrace.Afterthisisremovedtheplastic
dash pocket and bracket can be pulled out of the dash.
MTX.COM
6
Step6-Removethetwo(2)T40screwsholdingthedashboardinplace.
Step 7 - Pull the dashboard towards the back of the vehicle. There are locking clips on the right and
left side that hold it in place. The dash will pop out.
MTX.COM 7
Step 8 - Carefullylift the dash out of the vehicle. If the locking clips have fallen off, place them back
onto the locking tabs on the dash. These are needed to re-assemble the dashboard.
Step9-Removethetwo(2)10mmhexboltsthatareholdingthegloveboxtothevehicleframe.When
thescrewsareremovedthegloveboxcanbelowereddownandoutoftheenclosure.
Step10-Removetheve(5)T25screwsholdingthegloveboxtogether.Thegloveboxwillthenopen
like a book.
MTX.COM
8
Step11-Cutthe“binding”plastichingewitharazorknifetoseparatethefrontandbackoftheglove
box.Thebacksideofthegloveboxwillnolongerbeused.Thefrontsideofthegloveboxwillbe
attached to the enclosure.
Step12-Usingtheve(5)T25screwsthatwereremovedfromthefront/backassemblyoftheglove
box,attachthefrontofthegloveboxtotheRZRXP-10enclosure.Takecaretonotstripouttheplastic,
buttightenitenoughsothegasketsealsbetweentheenclosureandglovebox.
Step 13 - The enclosure can now be placed into the vehicle. Place the rectangular protrusion at an
angleintothedasharearst.Theenclosurecantheneasilyslideupintoplace.
MTX.COM 9
Step14-Holdtheenclosureupandalignthegloveboxscrewholeswiththevehicleframemount.
Replacethetwo(2)10mmhexboltsandtightentheenclosureinplace.Itmayhelptoplacea
supportingobjectundertheenclosuresobothhandsarefreetolineupthescrewholeswiththe
vehicle frame mount.
Step 15 - There are three mounting holes on the bottom of the enclosure to screw the base of
the enclosure into place. The furthest hole to the right uses the included 1" screw. The other two
mounting holes use the 1.5" screws. Tighten the screws down, but take care to not strip them. These
screws lock into the plastic foot board.
MTX.COM
10
Step 16 - Now that the enclosure is securely tightened in place, the power and signal wires need to
be connected to the battery and signal source.
• The Red wire should be connected directly to the battery’s positive terminal and fused with a
20A fuse.
• The Blackwireshouldbedirectlyconnectedtothebattery’snegativeterminal.
• If your vehicle is equipped with the Polaris®bussbarkit,theRedandBlackwirescanbe
connectedtothebussbarunderthehoodontherewall.TheRedwirewillstillneedtobe
fused.
• The BluewirecanbeconnectedtotheACC/KeyTurnOnlocatedonthebussbarofanyvehicle.
Step17-ConnecttheRCAinputstothesignalsourceofyourchoice
Step 18 - Turn the unit on and check to make sure everything works. Set the gain using the gain pot
that is attached to the orange / grey wires. Set the gain to the bass level desired.
Step19-TheincludedEBCcanbeconnectedandmountedtoadesiredlocationtoalloweasytrim
adjustmentofthebasslevelafterthegainhasbeenset.
Step 20 - Replace all the parts and screws that have been removed to return the RZR back to its
completely assembled state.
Inhaltsverzeichnis
Andere MTX Subwoofer Handbücher
MTX
MTX PROXP-20-SW Bedienungsanleitung
MTX
MTX Thunder T8512-04 Bedienungsanleitung
MTX
MTX CT12SW Bedienungsanleitung
MTX
MTX RTT12P Bedienungsanleitung
MTX
MTX Thunder TR7512-22 Bedienungsanleitung
MTX
MTX MTX Thunder 4000 T4104A Bedienungsanleitung
MTX
MTX Thunder TR7510-44 Bedienungsanleitung
MTX
MTX 120w RMS RT8PT Bedienungsanleitung
MTX
MTX Thunder TR4510-44 Bedienungsanleitung
MTX
MTX JackHammer JH4510-04 Bedienungsanleitung
MTX
MTX Thunder TS8512-22 Bedienungsanleitung
MTX
MTX Thunder TR7512-44 Bedienungsanleitung
MTX
MTX XT10-04 Thunder X Bedienungsanleitung
MTX
MTX US-XT12-04 Bedienungsanleitung
MTX
MTX Thunder TR5510-44 Bedienungsanleitung
MTX
MTX ThunderLink XT110P Bedienungsanleitung
MTX
MTX SUB8 Bedienungsanleitung
MTX
MTX Thunder TR4512-44 Bedienungsanleitung
MTX
MTX Thunder TR5512-44 Bedienungsanleitung
MTX
MTX T81544A Gebrauchsanweisung
