MULTISPAN CR-3K Bedienungsanleitung
Power Supply : 100-250V AC
Tripping Parameters : Under current
RESET MODE : ZVR (ZERO VALUE RESET)
Over current
SPP (Single Phase perversion)
Output: 1 Relay 1C/O ,5A, 230V AC Resistive load
Input Current : 200mA to 5Amp AC
Current Protection Relay
CR-3K
UNDER CURRENT KNOB
TRIP DELAY KNOB
OVER CURRENT KNOB
RELAY STATUS LED
MAIN LED
for visualisation of power
supply status
Rated Current : 5A
= Initial Delay Time (5 Sec)
Delay Time :
Power ON : 2 Sec
Initial Delay : 5 Sec
Recovery Time : 5 Sec
Trip Delay : 0 To 15 Sec Selectable
LED Indication:
OC - Over current
UC - Under current
SPP - Single Phase Prevension
R - Relay
Terminal Connection:
L1-L2
L2-L3
L3-L1
T
ON ON
P
15 18
16
TT
Phase
Loss
ON ON
T
ITD
TP= Power ON Delay (2 Sec)
= Trip Delay (0 TO 15 Sec Selectable )
RT = Recovery Time (5 Sec)
Control Function
Under Current Single Phase Prevention (SPP)
Over Current
2 7 10 15 20 22
OFF
ON
OFF
ON
ITD
Trip
Delay
1A
Power
ON
R,Y,B Phase
0
Power On:- 2 Sec
Initial Time Delay:- 5 Sec
Under Current:- 1A
Trip Delay time:- 0 TO 15 Sec (Selectable)
Reset Mode:- ZVR
27
ITD
2 7 10 15 20 22
OFF
ON
OFF
ON
ITD
Trip
Delay
4A
Power
ON
R,Y,B Phase
0
Power On:- 2 Sec
Initial Time Delay:- 5 Sec
Over Current:- 4A
Trip Delay time:- 0 TO 15 Sec (Selectable)
Reset Mode:- ZVR
27
ITD
1A
2 7 10 15 20 22
OFF
ON
OFF
ITD
Trip
Delay
4A
Power
ON
0
Power On:- 2 Sec
Initial Time Delay:- 5 Sec
Trip Delay time:- 0 TO 15 Sec (Selectable)
Reset Mode:-ZVR
27
1A
R
Y
B
L3
CR 3K
Input Current
200mA To 5Amp AC
Rated Current
5Amp AC
~
50/60 Hz
100
250V AC
L N
NO
C
NC
5A Resistive Load
230V AC
L2
L1
Relay
Made in India
S1 S2 S1 S2 S1 S2
Read complete instructions prior to installation and operation of the unit.
WARNING : Risk of electric shock.
SAFETY PRECAUTION
All safety related codifications, symbols and instructions that appear in this operating
manual or on the equipment must be strictly followed to ensure the safety of the operating
personnel as well as the instrument.
If all the equipment is not handled in a manner specified by the manufacturer, it might
impair the protection provided by the equipment.
NOTE:
All dimension are in mm.
WARNING GUIDELINES
WARNING : Risk of electric shock.
1. To prevent the risk of electric shock, power supply to the equipment must be kept OFF
while doing the wiring arrangement. Do not touch the terminals while power is
being supplied.
2. To reduce electro magnetic interference, use wire with adequate rating and twists of the
same of equal size shall be made with shortest connection.
3. Cable used for connection to power source, must have a cross section of 1mm or greater.
These wires should have insulations capacity made of at least 1.5kV.
4. A better anti-noise effect can be expected by using standard power supply cable for the
instrument.
Dimension
90
35
90.00
35.00
62.20
59.20
MECHANICAL INSTALLATION GUIDELINES
1) To install the instrument on a DIN rail, raise the clamp at the back of the instrument
and place it on the rail. Now release the clamp, so the instrument fits on the DIN rail.
2) Ensure proper fitting of the instrument by pulling it outwards.
3) To remove the instrument raise the clamp to release it from the DIN rail.
4) The equipment in its installed state must not come in close proximity to any heating
source, caustic vapors, oil steam, or other unwanted process byproducts.
5) Do not connect anything to unused terminals.
Product improvement and upgrade is a constant procedure.
Multispan reserves the right to change specifications without prior notice.Printing and typographical errors reserved.
Multispan Control Instruments Pvt. Ltd.
72/B,Phase 1, GIDC Estate,Vatva,Ahmedabad-382445,Gujarat,India.
Followus
+91-9978991476/9978991474/9978991482
INSTALLATION GUIDELINES
1. This equipment, being built-in-type, normally becomes a part of main control panel and in
such case the terminals do not remain accessible to the end user after installation
and internal wiring.
2. Do not allow pieces of metal, wire clippings, or fine metallic fillings from installation to
enter the product or else it may lead to a safety hazard that may in turn endanger life or
cause electrical shock to the operator.
3. Circuit breaker or mains switch must be installed between power source and supply
terminal to facilitate power ‘ON’ or ‘OFF’ function. However this mains switch or circuit
breaker must be installed at convenient place normally accessible to the operator.
4. Use and store the instrument within the specified ambient temperature and humidity
ranges as mentioned in this manual.
Andere MULTISPAN Relais Handbücher
MULTISPAN
MULTISPAN MI-532P Bedienungsanleitung
MULTISPAN
MULTISPAN ELR-19N Bedienungsanleitung
MULTISPAN
MULTISPAN EN-19N Bedienungsanleitung
MULTISPAN
MULTISPAN VPR-22U Bedienungsanleitung
MULTISPAN
MULTISPAN VPR 3P Bedienungsanleitung
MULTISPAN
MULTISPAN MI-632-24 Bedienungsanleitung
MULTISPAN
MULTISPAN VPR-22 Merkblatt
MULTISPAN
MULTISPAN ELR-63 Bedienungsanleitung
MULTISPAN
MULTISPAN ELR-19N Bedienungsanleitung
MULTISPAN
MULTISPAN SVR-22 Merkblatt
MULTISPAN
MULTISPAN VR-3KN Bedienungsanleitung
MULTISPAN
MULTISPAN CPR 126 Bedienungsanleitung
MULTISPAN
MULTISPAN VMR 13 Bedienungsanleitung
MULTISPAN
MULTISPAN ELR 19N-M1 Bedienungsanleitung
MULTISPAN
MULTISPAN MI-632 Merkblatt
MULTISPAN
MULTISPAN VPR 3P Bedienungsanleitung
MULTISPAN
MULTISPAN ELR-19N-M1 Merkblatt
MULTISPAN
MULTISPAN VPR-126-2R Bedienungsanleitung
MULTISPAN
MULTISPAN VTR-632 Bedienungsanleitung
MULTISPAN
MULTISPAN VMR 23 Merkblatt
