MULTISPAN MTC-1202 Bedienungsanleitung

SPECIFICATIONS

1. Microcontroller based. Double Display.

2. Size: 96 x 96 x 110 mm

Panel cutout: 92 x 92 mm

3. Supply: 230 V A.C. 50 Hz (SMPS).

4. Input Sensor: K Type.

5. Output: 2 Relays, 5 A/230V Relay contact.

R1 = For control purpose

R2 = For alarm purpose

1. DISPLAYS: There are two Displays.

A) Display 1 : Upper 4 digit display in RED colour indicates current process temperature value

(PV).

B) Display 2 : Lower 4 digit display in GREEN colour indicates current SET POINT (SP).

C) LED’s : 1) A small Red LED in upper right hand side as R1.

2) A small Red LED in lower right hand side as R2.

2. FRONT KEYS:

These front keys can be used to see and change current values of

FUNCTION DISPLAY RANGE

1. RATE 1  0.1 to 9.9°C/min

2. SET POINT 1  0 - 1191°C

3. HOLD TIME 1  01 to 999 min

4. RATE 2  0.1 to 9.9°C/min

5. SET POINT 2  0 - 1192°C

6. HOLD TIME 2  01 to 999 min

7. RATE 3  0.1 to 9.9°C/min

8. SET POINT 3  0 - 1193°C

9. HOLD TIME 3  01 to 999 min

10. RATE 4  0.1 to 9.9°C/min

11. SET POINT 4  0 - 1194°C

12. HOLD TIME 4  01 to 999 min

13. RATE 5  0.1 to 9.9°C/min

14. SET POINT 5  0 - 1195°C

15. HOLD TIME 5 HLd5 01 to 999 min

16. RATE 6  0.1 to 9.9°C/min

17. SET POINT 6  0 - 1196°C

18. HOLD TIME 6  01 to 999 min

19. RATE 7  0.1 to 9.9°C/min

20. SET POINT 7  0 - 1197°C

21. HOLD TIME 7  01 to 999 min

22. RATE 8  0.1 to 9.9°C/min

23. SET POINT 8  0 - 1198°C

24. HOLD TIME 8  01 to 999 min

25. RATE 9  0.1 to 9.9°C/min

26. SET POINT 9  0 - 1199°C

27. HOLD TIME 9  01 to 999 min

28. ALARM  0 to 1200°C

SET



ENT



OPERATING MANUAL

Nine Stage Profile Temperature Controller

MTC-1202

3. ADJUSTMENT OF SET POINTS:

(a) RATE1 [rat1 ]:

Press key for 2 seconds.

You are in SET MODE.

Display 1 will show rat1.

Display 2 will indicate current value of set point. Range is 0.1 to 9.9°C/min

You can change current value of this set point by following PROCEDURE.

Increase the parameter by key.

Decrease the parameter by key.

Press to store it in memory or press for next step.

If No key is pressed for 5 seconds previous value of parameter is retained and controller goes in control

mode.

(b) SET POINT 1 [Set1]:

Press key for 4 seconds.

You are in SET MODE.

Display 1 will show SEt1.

Display 2 will indicate current value of set point. Range is 0°C to 1200°C

You can change current value of this set point by following PROCEDURE.

Increase the parameter by key.

Decrease the parameter by key.

Press to store it in memory or press for next step.

If No key is pressed for 5 seconds previous value of parameter is retained and controller goes in control

mode.

Press key for 6 seconds.

You are in SET MODE.

Display 1 will show HLd1.

Display 2 will indicate current value of set point. Range is 1 to 999min.

You can change current value of this set point by following PROCEDURE.

Increase the parameter by key.

Decrease the parameter by key.

Press to store it in memory or press for next step.

If No key is pressed for 5 seconds previous value of parameter is retained and controller goes in control

mode.

NOTE: You can do the setting of the remaining parameters Rate2, Setpoint2, Holdtime2 Rate3, Setpoint3,

Holdtime3, Rate4, Setpoint4, Holdtime4, Rate5, Setpoint5, Holdtime5, Rate6, Setpoint6,

Holdtime6, Rate7, Setpoint7, Holdtime7, Rate8, Setpoint8, Holdtime8, & Rate9, Setpoint9,

Holdtime9 just like (a), (b) & (c).

NOTE: Here, the Control Action is On-Off & Hysteresis provided is fixed which is 2°C.

NOTE: Initially as the power is turned on Relay (R2) is turned ON. After completion of hold 9 the

process will be off and r2 goes OFF, when process temperature reaches at ALARM set point

and lower display will show end.

WORKING

1) As the power turns ON upper display shows room temperature/ process temperature and lower

display shows value current temperature, which changes according to the Rate (°C/min).

SET



SET

ENT



SET



SET

ENT



SET



SET

ENT



2) Initially when temperature reaches to the Set value decided, during that period RELAY 1 (R1)

turns ON. When it crosses to the Set value then RELAY R1 becomes OFF. Again when it reaches

SEt - HYS where Hysteresis is fixed 2°C it will turns ON again RELAY (R1).

3) Here, Relay R1 is for controlling purpose. It operates only when temperature reaches to the set

point.

4) By pressing both & keys one can see on the lower display which particular rate or

which particular hold time is going on.

5) Every Higher stage set point is always greater than all its lower stage set point except the last

stage (9) set point. The ninth stage set point can set to any value from 0 to 1200 °C.

Note # 1: When you operate this unit first time, you can freely play with key

to understand key operations, previously set parameter will remain unaffected as long as you

don’t press key.

CONNECTION DIAGRAM

SET





SET





ENT

Inhaltsverzeichnis

Andere MULTISPAN Temperaturregler Handbücher

MULTISPAN

MULTISPAN UTC-320 Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-121P Bedienungsanleitung

MULTISPAN

MULTISPAN PTC-1202A Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-221G Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-2202G Merkblatt

MULTISPAN

MULTISPAN UTC-113P Bedienungsanleitung

MULTISPAN

MULTISPAN TC-49 Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-321P Bedienungsanleitung

MULTISPAN

MULTISPAN TC-49 Bedienungsanleitung

MULTISPAN

MULTISPAN PTC-4202A-M1 Bedienungsanleitung

MULTISPAN

MULTISPAN TC-221P Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-114 Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-111P Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-121G Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-121P Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-2202 Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-4202G Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-423 Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-4203 Bedienungsanleitung

MULTISPAN

MULTISPAN TC-443 Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-4201A Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-121P Bedienungsanleitung

MULTISPAN

MULTISPAN TC-49P Bedienungsanleitung

MULTISPAN

MULTISPAN UTC-121P Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema