Murata DN-24 series Bedienungsanleitung

Revision History

Revision

Date

Author

Change Description

05/03/2012

F. Perkins

Initial issue

01/09/2015

R. Willett

Reformatted to comply with new Murata V.I.

RFM products are now

Murata products.

DN-24 Series

2.4 GHz

Serial Modems

User Guide

DN24G/GI Series User Guide Rev. 2.0 01-09-15 Page 1 of 44 www.murata.com

Important Regulatory Information

RFM Product FCC ID: HSW-DNT24

IC 4492A-DNT24

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

1) Re-orientate or relocate the receiving antenna,

2) Increase the separation between the equipment and the radiator,

3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected,

4) Consult the dealer or an experienced radio/TV technician for help.

FCC Antenna Gain Restriction:

The DN-24 series 2.4 GHz serial modems have been designed to operate with any dipole antenna of up

to 12 dBi of gain, any corner reflector antenna of up to 14 dBi gain, any patch antenna of up to 12 dBi

gain. The antenna(s) used for this transmitter must be installed to provide a separation distance of at

least 20 cm from all persons and must not be co-located or operating in conjunction with any other

antenna or transmitter.

IC RSS-210 Detachable Antenna Gain Restriction:

This radio transmitter, IC 4492A-DNT24, has been approved by the Industry Canada to operate with the

antenna types listed below with the maximum permissible gain and the required antenna impedance for

each antenna type indicated. Antenna types not included in this list, having a gain greater than the

maximum gain indicated for that type, are strictly prohibited for use with this device.

Le présent émetteur radio IC 4492A-DNT24 a été approuvé par Industrie Canada pour fonctionner

avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance

requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est

supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

Type Model Number Gain Impedance

Omnidirectional OD12-2400 12 dBi 50 ohm

Corner SCR14-2400CT 14 dBi 50 ohm

Patch PA2412 12 dBi 50 ohm

Dipole S181AH-2450S 2 dBi 50 ohm

DN24G/GI Series User Guide Rev. 2.0 01-09-15 Page 2 of 44 www.murata.com

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type

and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner

avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie

Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres

utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée

équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication

satisfaisante.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts

de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire

de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

Changes or modifications to a DN-24 series serial modem not expressly approved by Murata Electronics

N.A., Inc. may void the user’s authority to operate the module.

DN24G/GI Series User Guide Rev. 2.0 01-09-15 Page 3 of 44 www.murata.com

Table of Contents

1.0 DN-24 Series 2.4 GHz Serial Modems ...............................................................................................5

2.0 DN-24 Systems ...................................................................................................................................5

2.1 Point-to-Point Systems.....................................................................................................................5

2.2 Point-to-Multipoint Systems .............................................................................................................6

2.3 Store-and-Forward Systems............................................................................................................7

2.4 DN-24 Product Descriptions................................................................................................................ 8

3.0 Specifications ......................................................................................................................................9

3.1 Absolute Maximum Ratings.................................................................................................................9

3.2 System Specifications .........................................................................................................................9

3.3 LED Indicators.....................................................................................................................................9

4.0 Installation .........................................................................................................................................10

4.1 Mounting and Location......................................................................................................................10

4.2 Attaching the Antenna.......................................................................................................................11

4.3 DN-24G Connector Details................................................................................................................11

4.4 DN-24GI Connector Details...............................................................................................................12

4.5 Basic DN-24 Point-to-Point System Setup........................................................................................12

5.0 DN-24 Technical Reference..............................................................................................................13

5.1 RF Channel Access...........................................................................................................................13

5.2 DN-24 Addressing.............................................................................................................................13

5.3 Network Linking and Slot Registration..............................................................................................14

5.4 Transparent and Protocol-formatted Serial Data ..............................................................................14

6.0 DN-24 System Configuration.............................................................................................................15

6.1 Configuration Parameters..............................................................................................................15

6.2 Configuring a Basic Point-to-Point System....................................................................................15

6.3 Configuring a Basic Point-to-Multipoint System.............................................................................15

6.4 Configuring a Customized Point-to-Point or Point-to-Multipoint System.......................................16

6.5 Configuring a Store-and-Forward System .....................................................................................18

6.6 Slot Buffer Sizes, Number of Slots, Messages per Hop and Hop Duration...................................18

6.7 Configuring the Serial Port.............................................................................................................21

7.0 DN-24 Protocol-formatted Messages................................................................................................21

7.1 Protocol Formats............................................................................................................................21

7.2 Message Types..............................................................................................................................21

7.3 Message Format Details................................................................................................................22

7.4 Configuration Parameter Registers................................................................................................28

7.4.1 Bank 0x00 - Transceiver Setup ..................................................................................................28

7.4.2 Bank 0x01 - System Settings......................................................................................................30

7.4.3 Bank 0x02 - Status Parameters..................................................................................................32

7.4.4 Bank 0x03 - Serial Settings ........................................................................................................33

7.4.5 Bank 0x04 - Host Protocol Settings............................................................................................34

7.4.6 Bank 0x0FF - Special Functions.................................................................................................35

7.5 Protocol-formatted Message Example........................................................................................35

8.0 Utility Program...................................................................................................................................36

8.1 Serial Communication and Radio Configuration............................................................................38

9.0 Warranty............................................................................................................................................44

DN24G/GI Series User Guide Rev. 2.0 01-09-15 Page 4 of 44 www.murata.com

1.0 DN-24 Series 2.4 GHz Serial Modems

The DN-24 series 2.4 GHz serial modems provide a low cost, ready-to-use solution for robust wireless

data communications in the 2.4 GHz ISM band. There are currently two products in the DN-24 series, the

DN-24G and the DN-24GI. The DN-24G provides an RS-232C serial interface with optional hardware flow

control. The DN-24GI offers a selectable 3-wire RS-232C interface or a two-wire, multi-drop RS-485

interface. All DN-24 series modems are based on Murata’s DNT24 frequency hopping spread spectrum

(FHSS) transceiver, and can communicate with other DNT24-based modems and sensor nodes, as well

as customer developed products. DN-24 series modems are supplied with a dipole antenna and a wall-

plug power supply. A DN-24 transmits data at 250 kbps. The RF output power can be set up to 100 mW

EIRP using the supplied 2 dBi dipole antenna. Optional high-gain directional and omni-directional

antennas are available to extend operating range where local regulations allow it. DN-24 series modems

are well suited for sensor and data networks carrying moderate traffic that need robust communications in

locations with non-ideal RF propagation and/or where RF interference or noise are present.

Key Features of the DN-24 Series 2.4 GHz Serial Modems include:

-2.4 GHz wireless connectivity for RS-232C or RS-485 serial interfaces

-Optional 128-Bit AES Encryption

-Point-to-point, Point-to-multipoint, Peer-to-peer and

Store & Forward Capabilities

-Frequency Hopping Spread Spectrum Transceiver

-250 kbps RF Data Rate

-Transmitter Power up to 100 mW EIRP with 2 dBi Antenna

-FCC, Canadian IC Certified and CE Marked for Unlicensed Operation

2.0 DN-24 Systems

DN-24 wireless serial modems can be configured to operate in one of three modes - base, remote or

router. A base controls a DN-24 system, and interfaces to an application host such as a PC. A remote

simply functions to transmit or receive data. A router alternates between functioning as a remote on one

hop and a network base on the next hop. When acting as a remote, the router stores messages it

receives from its parent, and then repeats the messages to its child radios when acting as a network

base. Likewise, a router will store messages received from its child radios when acting as a base, and

repeat them to its parent when acting as a remote. Any message addressed directly to a router is

processed by the router rather than being repeated.

2.1 Point-to-Point Systems

A DN-24 system contains at least one network. The simplest DN-24 topology is a point-to-point system,

as shown in Figure 2.1.1. This system consists of a base and one remote forming a single network. Point-

to-point systems are often used to replace wired serial connections.

DN24G/GI Series User Guide Rev. 2.0 01-09-15 Page 5 of 44 www.murata.com

Figure 2.1.1

2.2 Point-to-Multipoint Systems

Figure 2.2.1 shows the topology of a point-to-multipoint (star) system, which consists of a base and more

than one remote in a single network. Point-to-multipoint systems are typically used for data, sensor and

alarm systems. While most traffic in a point-to-multipoint system is between the base and the remotes,

DN-24 technology also allows for peer-to-peer communication from one remote to another.

Figure 2.2.1

DN24G/GI Series User Guide Rev. 2.0 01-09-15 Page 6 of 44 www.murata.com

2.3 Store-and-Forward Systems

Figure 2.3.1 shows the topology of a store-and-forward system, which consists of a base, one or more

routers, one or more remotes, and two or more networks. Networks in a store-and-forward system form

around the base and each router. The base and the routers are referred to as the parents of the networks

they form. The rest of the radios in each network are referred to as child radios. Note that a router is a

child of the base or another router while being the parent of its own network. Each network parent

transmits beacons to allow child radios to synchronize with its hopping pattern and join its network.

Different frequency hopping patterns are used by the parent radios in a system, minimizing interference

between networks.

Store-and-forward systems are used to cover larger areas than is possible with point-to-point or point-to-

multipoint systems. The trade-off in store-and-forward systems is longer delivery times due to receiving

and retransmitting a message several times. Store-and-forward systems are especially useful in

applications such as agriculture where data is only collected periodically.

Figure 2.3.1

DN24G/GI Series User Guide Rev. 2.0 01-09-15 Page 7 of 44 www.murata.com

2.4 DN-24 Product Descriptions

There are currently two products in the DN-24 series, the DN-24G and the DN-24GI. The DN-24G

provides an RS-232C serial interface. The DN-24GI offers a selectable RS-232C interface or a two-wire,

multi-drop RS-485 interface. DN-24 series modems are based on Murata’s DNT24 frequency hopping

spread spectrum (FHSS) transceiver, and can communicate with other DNT24-based modems and

sensor nodes, as well as customer developed products.

DN-24 series modems are supplied with a reverse SMA dipole antenna and a universal wall-plug power

supply. DN-24 modems transmit data at 250 kbps. The transmitter output power can be set up to 100 mW

EIRP using the supplied 2 dBi dipole antenna. Optional high-gain directional and omni-directional

antennas are available from Murata to extend operating range where allowed by local regulations.

DN-24 series modems are well-suited for sensor and data networks carrying moderate traffic that need

robust communications in locations with non-ideal RF propagation and/or where RF interference or noise

are present.

As shown in Figures 2.4.1 and 2.4.2, serial data to/from a DN-24G is routed through an RS232C signal

converter. In the case of a DN-24GI, serial data is routed through an RS-232C/RS-485 signal converter.

When terminal 3 is left unconnected on the DN-24GI, serial communication is 3-wire RS-232C. When

terminal 3 is connected to terminal 2 or 4, serial communication is 2-wire, multi-drop capable RS-485.

Terminal 3 has no function in a DN-24G. The switching regulator used in all DN-24 modems supports a

wide voltage range on the DC power input, from 9 to 24 Vdc.

Figure 2.4.1 Figure 2.4.2

DN24G/GI Series User Guide Rev. 2.0 01-09-15 Page 8 of 44 www.murata.com

3.0 Specifications

3.1 Absolute Maximum Ratings

Rating Value Units

Power Supply Input Voltage Range -0.5 to +24 V

Non-Operating Ambient Temperature Range -40 to +85

3.2 System Specifications

Characteristic

Sym

Notes

Minimum

Typical

Maximum

Units

Operating Frequency Range

2406

2475

MHz

Hop Dwell Time

100

Number of RF Channels

15 or 24

Modulation

FSK

RF Data Transmission Rate

250 kbps

Receiver Sensitivity @ 10

-5

BER

-100

dBm

EIRP RF Output Power Level, 2 dBi Antenna

100

Optimum Antenna Impedance

Ω

RF Connection

RSMA Coaxial Connector

Network Topologies Point-to-Point, Point-to-Multipoint,

Peer-to-Peer and Store & Forward

Access Scheme

Ad Hoc TDMA

DN-24G RS-232C

9-pin connector, hardware flow control optional

DN-24GI RS-232C Configuration

3-wire, no hardware flow control required

DN-24GI RS-485 Configuration

2-wire, multi-drop capable

Serial Port Baud Rates 1.2, 2.4, 4.8, 9.6, 14.4, 19.2, 28.8,

38.4, 57.6, 115.2, 230.4, 250.0 kbps

Power Supply Voltage Range VCC

+9 +24

Peak Transmit Mode Current

190

Average Receive Mode Current:

Base, Continuous Data Stream

129

Remote, linked, No Data

Remote, Continuous Data Stream

Nominal Dimensions

3.3 x 3.2 x 1 inches (84.6 x 82.0 x 25.4 mm)

Mounting Left and Right Flanges, Two Pre-drilled Holes

in Each Flange

Operating Temperature Range

-40 85

Operating Relative Humidity Range, Non-condensing

10 90 %

3.3 LED Indicators

Ref Name I/O Description

1 ACTIVITY O Left-most LED on the front of the unit, amber, indicates RF communications activity.

2 LINK O Middle LED on the front of the unit, red. On a base, this LED indicates one or more remotes

are linked to it. On a remote, this LED indicates it is linked to the base.

POWER

Right-most LED on the front of the unit, green, indicates the unit is powered up.

DN24G/GI Series User Guide Rev. 2.0 01-09-15 Page 9 of 44 www.murata.com

4.0 Installation

4.1 Mounting and Location

The DN-24G and DN-24GI case outline drawings are shown in Figures 4.1.1 and 4.1.2. The supplied

antenna is hinged, allowing it to be set vertically with the case mounted either horizontally or vertically.

The DN-24 case is designed for indoor use. It must be installed in a weather proof enclosure when used

outdoors, such as a NEMA 4X enclosure. The enclosure must be made of plastic or other materials with

low RF attenuation to avoid compromising antenna performance. Metal enclosures are not suitable for

use with internal antennas as they will block antenna radiation and reception.

DN-24 modems should be mounted at least six feet above the floor (ground) to achieve good

communication reliability in a typical office or retail location. To achieve maximum range and reliability,

especially in industrial locations, the DN-24 should be mounted as high as practical. Murata offers a

number of high gain antennas that can be used to further extend the DN-24’s range. The use of these

antennas is not allowed in all geographical regions; contact RFM’s technical service department for

additional details.

Figure 4.1.1

DN24G/GI Series User Guide Rev. 2.0 01-09-15 Page 10 of 44 www.murata.com

Inhaltsverzeichnis

Andere Murata Modem Handbücher

Murata

Murata HN-250 Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung