Murphy PowerView PV1000 Montageanleitung

00-02-0599

07-19-07

Section 78

PowerView™

Model PV1000

Hardware Installation Manual

PHASE OUT / DISCONTINUED

Check Availability

In order to consistently bring you the highest quality, full featured products, we reserve the right to change our

specifications and designs at any time. The latest version of this manual can be found at www.fwmurphy.com.

Warranty - A limited warranty on materials and workmanship for one year is given with this FW Murphy product.

A copy of the warranty may be viewed or printed by going to www.fwmurphy.com/support/warranty.htm

Please read the following information before installing.

BEFORE BEGINNING INSTALLATION OF THIS MURPHY

PRODUCT:

•Read and follow all installation instructions.

•Disconnect all electrical power to the machine.

•Make sure the machine cannot operate during installation.

•Follow all safety warnings of the machine manufacturer.

•Please contact FW MURPHY immediately if you have any

questions.

PHASE OUT / DISCONTINUED

Check Availability

Table of Contents

Product Information................................................................................................................ 1

Inspecting Package Contents.......................................................................................1

Hardware Installation.............................................................................................................. 2

Dash-Mounted Installation............................................................................................2

Gimbal Mount Installation.............................................................................................3

Wiring Instructions ................................................................................................................. 4

Single Engine...............................................................................................................4

Dual Engine Static Addressing.....................................................................................5

NMEA Wiring................................................................................................................6

PVA Gages ..................................................................................................................7

Pin Specifications for Deutsch DT04-6P Style Connections.........................................8

Wiring Schematic.........................................................................................................9

Specifications........................................................................................................................ 10

PHASE OUT / DISCONTINUED

Check Availability

(THIS PAGE INTENTIONALLY LEFT BLANK)

PHASE OUT / DISCONTINUED

Check Availability

Section 78 00-02-0599

07-19-07 - 1 -

Product Information

The PowerView™display is designed for instrumentation on electronically controlled engines

communicating using the SAE J1939 Controller Area Network (CAN), NMEA 2000 (GPS

features) or a proprietary blend of protocols. The PowerView display is a multifunction tool that

enables operators to view many different engine, equipment, or transmission parameters and

service codes, and can support many devices simultaneously.

Two mounting options are provided for the display. The in-dash mounting option requires a

hole to be cut for insertion of the display. A plastic installation template P/N 78000386 is

included in the box and a drawing is also provided in the back of this document.

The gimbal-mount method enables the display to be installed on a flat surface. Its design

allows you to rotate and tilt the unit for the best display position for the operator’s viewing.

NOTE: Please read the PV1000 Operations Manual for detailed instruction on

the use and operation of the display.

Inspecting Package Contents

Before attempting to install the product, it is recommended that you ensure all parts are

accounted for and inspect each item for damage (which sometimes occurs during shipping).

The items included in the box are:

•PV1000 unit

•front cover snap on – P/N 78-05-0302

•installation kit – P/N 78-00-0386 includes:

•8 mounting screws and nuts

•extra SD card cover

•back plate (can be used as mounting template)

•Installation manual

•Operations manual

PHASE OUT / DISCONTINUED

Check Availability

Section 78 00-02-0599

07-19-07 - 2 -

Hardware Installation

The following instructions will guide you through installing the PowerView display.

Dash-Mounted Installation

Tools needed.

•Drill with 9/64” size bit

•Jig Saw

•Wrench or socket for #6 Keps locking nuts (provided) to studs

Preparing the Dash

Determine the location of the PowerView in the dash. Use the Installation Template (included

in the box) as a guideline to cut a hole in the dash to the specified dimensions. Drill holes

where indicated on the template for the mounting screws.

NOTE: Use the plastic template included in the box whenever possible.

If you must use the paper template from the manual and you downloaded this

document from the FW Murphy website, be aware that the pdf file may not

automatically print to scale. When submitting the file for print, you will need to

select “None” for Page Scaling. Check the accuracy of the printed template by

verifying the measurements labeled on the template are correct.

If this manual was supplied with your product, the template will be correct.

Mounting the Unit

1. Attach the eight threaded studs to the back of the PowerView case.

2. Place the back side of the display through the opening in the dash.

3. Use the studs to line up the unit with the drilled holes.

4. Push the unit through the opening and studs through the drilled holes until the back of

the case is flush.

5. Use the #6 Keps locking nuts provided to tighten unit to the dash. Use the appropriate

wrench or socket to tighten. Torque lock nuts to 8-10 inch pounds.

PHASE OUT / DISCONTINUED

Check Availability

Section 78 00-02-0599

07-19-07 - 3 -

Gimbal Mount Installation

Tools Needed

•Flathead or Phillips Screwdriver (depending upon screws used for mounting)

•Drill with 9/64” size bit

•Hole saw

•Three (3) 6-32 stainless panhead screws (self tapping or machine screws)

(length = panel thickness + 0.125”)

Mounting the Unit

1. Determine where the gimbal mount will be located on the dash. Attach the PowerView

to the gimbal mount and tighten the adjustment knob to hold in place.

2. Mark the screw holes needed for the

mount.

3. Drill holes for the mount.

4. Create a “pass-through” hole for the wires

from the unit. This hole can be partially

hidden by the triangle base of the gimbal

mount

IMPORTANT! Be sure to smooth edges

and install some type of cable protection to

prevent cable chaffing, cuts and abrasions.

Not taking this step could result in failures.

5. Pull the wires through the hole for

connection.

6. Attach gimbal with the bolt and nut

provided.

PHASE OUT / DISCONTINUED

Check Availability

Section 78 00-02-0599

07-19-07 - 4 -

Wiring Instructions

The following illustrations are examples of various typical quick-connect options for 1 or 2

engine setups and gages. Wiring harnesses are sold separately.

Single Engine

Software Configuration for Single Engine Setup

To set the software configuration for single engine, on the System Settings screen, under

Wiring Configuration, select Engine(s) – Single Harness to Plug A – Engine 1, Engine 2.

PHASE OUT / DISCONTINUED

Check Availability

Section 78 00-02-0599

07-19-07 - 5 -

Dual Engine Static Addressing

NOTE: Port A and B have different connector keys to ensure proper connection.

All cables are black with the exception of cables for Port B, which are yellow.

Software Configuration for Dual Engine Static Addressing

To set the software configuration for dual engine static addressing, on the System Settings

screen, under Wiring Configuration, select Engine(s) – Dual Harness to Plug A & B –

Engine1, Engine 2.

PHASE OUT / DISCONTINUED

Check Availability

Section 78 00-02-0599

07-19-07 - 6 -

NMEA Wiring

NOTE: The NMEA wire harness contains blocking pins that only allow the cable

to be connected to Plug D.

Software Configuration for NMEA Setup

If only NMEA devices such as GPS are connected to Plug D, and engines are connected to

Plug A or B, then use the appropriate single or dual engine configuration settings.

NOTE: NMEA can be used in conjunction with all other engine options listed in

this manual.

PHASE OUT / DISCONTINUED

Check Availability

Andere Handbücher für PowerView PV1000

Inhaltsverzeichnis

Andere Murphy Automobilelektronik Handbücher

Murphy

Murphy POWERVIEW PV450 Bedienungsanleitung

Beliebte Automobilelektronik Handbücher anderer Marken

GoldCruise

GoldCruise GC90Ci Bedienungsanleitung

DRG

DRG LC 120 Bedienungsanleitung

Blue Ox

Blue Ox BX8848 Bedienungsanleitung

Dometic

Dometic MAGICWATCH MWE890K Bedienungsanleitung

Perfect Power

Perfect Power SMT8-T5 Bedienungsanleitung

Honeywell

Honeywell Thor VM3A Bedienungsanleitung

Waeco

Waeco MagicWatch MWE250 Bedienungsanleitung

Rydeen

Rydeen BKM091 Bedienungsanleitung

Skoda

Skoda 5E0 054 630 Bedienungsanleitung

VDO

VDO SENDER UNIT 2159-0 Bedienungsanleitung

iDataLink

iDataLink maestro Rr Bedienungsanleitung

Audiovox

Audiovox PRO-PDA15 Bedienungsanleitung

Movon

Movon MDAS-3LFFHD Bedienungsanleitung

Pioneer

Pioneer Comfort adapter CA-D-PI.150 Bedienungsanleitung

Dietz

Dietz 1110 Bedienungsanleitung

Crux

Crux RVCFD-79 Bedienungsanleitung

Nonda

Nonda ZUS Bedienungsanleitung

iDataLink

iDataLink Maestro Bedienungsanleitung