MUTOH ValueJet VJ-1638UH Installations- und Betriebshandbuch

Daily Maintenance Sheet for VJ-1638UH

CS3002-05 -1-

The content of this documents are based on the specication of the rmware Ver.1.04 or later.

Daily maintenance

g h

When to maintain:

After operation (Be sure to perform the following maintenance)

When the media strikes the print head

Required Items:

(a) Plastic gloves (Supplied accessories or

Commercial item)

(b) Rubber gloves (Supplied accessories or

Commercial item)

(d) Paper towel (Supplied accessories)

or Polyester knit wiper (Optional accessories)

(e) Dropper (Supplied accessories)

(f) Dedicated maintenance cleaner (Optional

accessories)

(g) Plastic cup (Supplied accessories)

(h) Cleaning stick (Supplied accessories or Optional

accessories)

(i) Stick scraper (Supplied accessories)

or Scraper (Supplied accessories)

Use a paper towel supplied with the printer or optional

Polyester knit wiper. DO NOT use a tissue.

Lints or akes on tissue may cause damage to the print head.

DO NOT use non-dedicated maintenance cleaner.

Press the [MENU] key on the operation panel.

When [Menu 1: Sleep Mode >] appears on the operation panel, press the [>] key.

Press the [+] / [-] key on the operation panel to select [Sleep Mode 3: Start].

Press the [Enter] key on the operation panel.

When [Start Sleep Mode?] appears on the operation panel, press the [Enter] key.

When [Daily Maint.: Start] appears on the operation panel, press the [Enter] key.

When [Daily Maint.: End] appears on the operation panel, you can start the maintenance

with following steps.

Preparation:

Wear the rubber gloves (white) over the plastic

gloves (pink).

Wear protective goggles.

Important!

Before performing maintenance, make sure to read

“How to handle UV inkjet printer / its supplies”

(supplied with the printer).

Skin or eye contact with UV curable ink may cause skin

inammation or allergic reaction.

For this operation, be sure to wear the supplied gloves

(or solvent resistant gloves) and goggles to prevent ink

from contacting with your eyes or skin.

CAUTION

Make sure to complete this maintenance within 10 minutes while the printer is in Daily maintenance state.

Open the maintenance cover on the left of the

printer and remove it.

-2-CS3002-05

Important!

During cleaning, please note the followings:

• Always follow this steps to perform daily maintenance.

When moistening the surface of nozzles, do not use the cleaning stick already used to clean the print head

circumference, cleaning wiper or cap circumference. Doing so may result in damage to the print head.

• Always use a new cleaning stick and dampen it with dedicated maintenance cleaner.

DO NOT use non-dedicated maintenance cleaner. It may cause nozzle clogging.

• Do not touch the tip of a cleaning stick with ngers. If sebum is adhered, it can cause damage to the print

head.

• Do not reuse a cleaning stick. Dusts can adhere causing damage to the print head.

2. Moistening the surface of print head nozzles

Put a cleaning stick in the plastic cup.

Use the dropper to dampen the swab of

cleaning stick with dedicated maintenance

cleaner.

(Amount used: 0.5 ml)

DO NOT rub into the nozzle surface.

It can cause damage to the print head.

If the entire nozzle surface has been moistened,

you can stop it.

Lightly touch with the cleaning stick to moisten

the nozzle surface.

Repeat it a couple of times to moisten the entire

nozzle surface.

Next clean the print head circumference.

Look the bottom of the carriage.

Using the cleaning stick dampened with the

maintenance cleaner, moisten the surface of the

print head nozzles.

1.Cleaning of UV Lamp

Check for any ink or dust on the UV lamps (x2).

If any ink or dust is found, using a paper towel, remove ink and dust from the UV lamp.

If no ink or dust is found on the UV lamp, skip this step and move on to “2. Moistening the

surface of print head nozzles”.

Important!

• Make sure to use the scraper supplied with the printer.

• Never use the corner of the scraper. It can damage the UV lamp.

• When using the scraper, do not apply too much pressure to the lamp. It can damage the UV lamp.

*If ink deposits cannot be removed with the paper towel, use the scraper supplied with the

printer.

Press the scraper on the ink deposits with a slight angle and scrape o the ink deposits.

Use the paper towel to clean the ink scraped from the lamp.

Scraper

*The illustration below shows an example when cleaning the left UV lamp.

Next moisten the surface of print head nozzles.

*When cleaning the right side UV lamp, use the stick scraper supplied with the printer.

Open the front cover. Then, press the stick scraper on the UV lamp surface and scrape ink

deposits o.

Use the paper towel to clean the ink scraped from the lamp.

-3-CS3002-05

Open the maintenance cover on the right of the

printer and remove it.

4. Cleaning of cleaning wiper and the circumference of the cap

Attach the maintenance cover on the right of the printer and close it.

Next finish the daily maintenance.

DO NOT touch the absorber

(the yellow portions in the illustration right)

Use the cleaning stick to remove the ink and

dust on the circumference of the cap.

Cleaning required

Use the cleaning stick to clean the left side

surface of the cleaning wiper (a black rubber

part).

Clean the right side surface of the cleaning

wiper.

3. Cleaning of print head circumference

1Look the bottom of the carriage.

Check if dusts and ink deposit are adhered.

Print head circumference (silver metal part)

Print head guide part (black plastic part)

If maintenance cleaner is splashed onto the printer,

use a paper towel to wipe it o.

If dusts or ink deposit are adhered, clean with a cleaning stick.

Print head circumference (silver metal part)

Print head guide part (black plastic part)

Cleaning required

DO NOT touch the surface of a print head (the yellow portions in the illustration below)

Attach the maintenance cover on the left of the printer and close it.

Next clean the cleaning wiper and the cap circumference.











Print head circumference

Print head guide part

-4-

Maintenance before leaving printer in sleep mode for a long time

Make sure that there is enough ink in ink cartridges.

Empty the waste uid tank.

Perform “Daily maintenance (refer to this sheet)”.

To leave the printer in sleep mode for one week or longer, when one week has passed,

perform the following:

Check the ink level.

Replace the relevant ink cartridge if “Ink Low” is displayed.

Agitate the ink in the ink cartridge.

Operation manual ”Disposal the waste uids”

Operation manual ”Ink Status menu”, ” Replacing ink cartridge”

CS3002-05

5. Finishing daily maintenance

1Press the [Enter] key on the operation panel.

The printer automatically performs the Short

cleaning.

When the Short cleaning is complete, the printer

automatically enters to sleep mode.

Do not reuse a cleaning stick.

Dusts can adhere causing damage to the print head.

Check that the lid of the maintenance cleaner is shut properly and store it.

Important!

Daily Maint. : End

Dispose of the used cleaning stick.

Use a paper towel to wipe the maintenance cleaner off the dropper.

Dispose of the maintenance cleaner in the plastic cup and dry the cup well using the paper

towel.

Now the daily maintenance is complete.

For purchasing the maintenance items, contact your local Mutoh dealer or

nearest Mutoh sales oce.

Note

VJ-ULVA1-ML500Dedicated Maintenance cleaner

Part NumberName Minimum q’ty per order

PJ-POLYNITWPolyester knit wiper

RH2 Clean stickClean stick

300

100

Andere Handbücher für ValueJet VJ-1638UH

Andere MUTOH Drucker Handbücher

MUTOH

MUTOH VJ-426UF Benutzerhandbuch

MUTOH

MUTOH valuejet 1614 Bedienungsanleitung

MUTOH

MUTOH ValueJet VJ-1624 Bedienungsanleitung

MUTOH

MUTOH Rockhopper 38 Bedienungsanleitung

MUTOH

MUTOH VJ-1628TD Bedienungsanleitung

MUTOH

MUTOH ValueJet 1608 HS Bedienungsanleitung

MUTOH

MUTOH Toucan Hybrid PJ-162-FE Bedienungsanleitung

MUTOH

MUTOH DrafStation RJ-900X Bedienungsanleitung

MUTOH

MUTOH Spitfire 100 Extreme Bedienungsanleitung

MUTOH

MUTOH VJ-1627MH Bedienungsanleitung

MUTOH

MUTOH Rockhopper 3 Extreme Bedienungsanleitung

MUTOH

MUTOH VJ-1324 Bedienungsanleitung

MUTOH

MUTOH Falcon Outdoor Jr. Bedienungsanleitung

MUTOH

MUTOH ValueJet VJ-1624 Bedienungsanleitung

MUTOH

MUTOH RJ-900X series Bedienungsanleitung

MUTOH

MUTOH Osprey 75 Bedienungsanleitung

MUTOH

MUTOH VJ-1324 Bedienungsanleitung

MUTOH

MUTOH Falcon Outdoor 46 Bedienungsanleitung

MUTOH

MUTOH VJ-628 ValueJet Bedienungsanleitung

MUTOH

MUTOH VJ-628 ValueJet Bedienungsanleitung

MUTOH

MUTOH Valuevet VJ-1638 Bedienungsanleitung

MUTOH

MUTOH XPJ-461UF Bedienungsanleitung

MUTOH

MUTOH VJ-628 ValueJet Benutzerhandbuch

MUTOH

MUTOH ValueJet VJ-1638UH Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung