8
NL
M1.1.MWM100.NLFREN 23082018
4 Meetinstructies
4�1 AC/DC spanning meten
1. Sluit de zwarte testkabel aan de COM aansluiting aan en de rode kabel aan de VΩHz aansluiting.
2. Draai de draaiknop naar of .
3. Druk op SEL om tussen AC/DC om te schakelen.
4. Zet de sensoren op de correcte testpunten van het circuit om de spanning te meten.
5. Lees de gemeten spanning op de display.
*Meet geen spanning die de in de specicaties aangegeven grenzen overschrijdt.
*Raak het hoogspanningscircuit niet aan tijdens de metingen�
4�2 AC/DC stroom meten
1. Sluit de zwarte testkabel aan de COM aansluiting aan en de rode kabel aan de VΩHz aansluiting of aan de A mA
aansluiting (de keuze is afhankelijk van de te meten stroom).
2. Draai de draaiknop naar of .
3. Druk op SEL om tussen AC/DC om te schakelen.
4. Breek het te meten circuit, sluit de testkabels over de stroomonderbreker aan en schakel de stroomtoevoer in.
5. Lees de gemeten stroom op de display.
*Meet geen stroom die de in de specicaties aangegeven grenzen overschrijdt.
*Gebruik de A mA aansluiting en de modus om onbekende stromen te meten� Schakel vervolgens
naar de VΩHz aansluiting over en naar de modus indien nodig.
*Voer bij deze instelling geen spanning in�
4�3 Weerstand meten
1. Sluit de zwarte testkabel aan de COM aansluiting aan en de rode kabel aan de VΩHz aansluiting.
2. Draai de draaiknop naar , et de display zal “OL” tonen.
3. Zet de sensoren op de gewenste testpunten van het circuit, om de weerstand te meten.
4. Lees de gemeten weerstand op de display.
*Koppel de stroomtoevoer van het circuit los en ontlast alle condensatoren voordat u de weerstand test�
*Voer bij deze instelling geen spanning in�
4�4 Continuïteitstest
1. Sluit de zwarte testkabel aan de COM aansluiting aan en de rode kabel aan de VΩHz aansluiting.
2. Draai de draaiknop naar , druk op SEL om naar de Continuïteit modus te gaan.
3. Zet de sensoren op de gewenste testpunten van het circuit.
4. Het ingebouwde geluidssignaal zal een pieptoon geven wanneer de weerstand minder dan 50 Ω bedraagt, wat op
kortsluiting duidt.
*Voer bij deze instelling geen spanning in�
Measurements Instruction
Measure AC/DC Voltage
1. Connect the black test lead to the COM
Terminal and the red lead to the VΩHz
Terminal.
2. Turn the rotary switch to or to .
3. Press SEL to toggle between AC/DC.
4. Touch the probes to the correct test points of
the circuit to measure the voltage.
5. Read the measured voltage on the display.
Measure AC/DC Current
1. Connect the black test lead to the COM
Terminal and the red lead to the VΩHz
Terminal or the AmA Terminal (choose based
on the value of the current to be measured).
10
*Do not measure voltage that exceeds the extremes
as indicated in the Specifications.
*Do not touch high voltage circuit during
measurements.
Measurements Instruction
Measure AC/DC Voltage
1. Connect the black test lead to the COM
Terminal and the red lead to the VΩHz
Terminal.
2. Turn the rotary switch to or to .
3. Press SEL to toggle between AC/DC.
4. Touch the probes to the correct test points of
the circuit to measure the voltage.
5. Read the measured voltage on the display.
Measure AC/DC Current
1. Connect the black test lead to the COM
Terminal and the red lead to the VΩHz
Terminal or the AmA Terminal (choose based
on the value of the current to be measured).
10
*Do not measure voltage that exceeds the extremes
as indicated in the Specifications.
*Do not touch high voltage circuit during
measurements.
2. Turn the rotary switch to or .
3. Press SEL to toggle between AC/DC.
4. Break the circuit path to be measured, connect
the test leads across the break and apply
power.
5. Read the measured current on the display.
Measure Resistance
1. Connect the black test lead to the COM
Terminal and the test lead to the VΩHz
Terminal.
2. Turn the rotary switch to ,and the display
will show “ ”.
3. Touch the probes to the desired test points of
the circuit to measure the resistance.
4. Read the measured resistance on the display.
11
*Do not measure current that exceeds the extremes
as indicated in the Specifications.
*Use the A mA Terminal and the Mode when
you are measuring an unknown current. Then
switch to the VΩHz Terminal and the Mode if
necessary.
*Do not input voltage at this setting.
2. Turn the rotary switch to or .
3. Press SEL to toggle between AC/DC.
4. Break the circuit path to be measured, connect
the test leads across the break and apply
power.
5. Read the measured current on the display.
Measure Resistance
1. Connect the black test lead to the COM
Terminal and the test lead to the VΩHz
Terminal.
2. Turn the rotary switch to ,and the display
will show “ ”.
3. Touch the probes to the desired test points of
the circuit to measure the resistance.
4. Read the measured resistance on the display.
11
*Do not measure current that exceeds the extremes
as indicated in the Specifications.
*Use the A mA Terminal and the Mode when
you are measuring an unknown current. Then
switch to the VΩHz Terminal and the Mode if
necessary.
*Do not input voltage at this setting.
2. Turn the rotary switch to or .
3. Press SEL to toggle between AC/DC.
4. Break the circuit path to be measured, connect
the test leads across the break and apply
power.
5. Read the measured current on the display.
Measure Resistance
1. Connect the black test lead to the COM
Terminal and the test lead to the VΩHz
Terminal.
2. Turn the rotary switch to ,and the display
will show “ ”.
3. Touch the probes to the desired test points of
the circuit to measure the resistance.
4. Read the measured resistance on the display.
11
*Do not measure current that exceeds the extremes
as indicated in the Specifications.
*Use the A mA Terminal and the Mode when
you are measuring an unknown current. Then
switch to the VΩHz Terminal and the Mode if
necessary.
*Do not input voltage at this setting.
2. Turn the rotary switch to or .
3. Press SEL to toggle between AC/DC.
4. Break the circuit path to be measured, connect
the test leads across the break and apply
power.
5. Read the measured current on the display.
Measure Resistance
1. Connect the black test lead to the COM
Terminal and the test lead to the VΩHz
Terminal.
2. Turn the rotary switch to ,and the display
will show “ ”.
3. Touch the probes to the desired test points of
the circuit to measure the resistance.
4. Read the measured resistance on the display.
11
*Do not measure current that exceeds the extremes
as indicated in the Specifications.
*Use the A mA Terminal and the Mode when
you are measuring an unknown current. Then
switch to the VΩHz Terminal and the Mode if
necessary.
*Do not input voltage at this setting.
2. Turn the rotary switch to or .
3. Press SEL to toggle between AC/DC.
4. Break the circuit path to be measured, connect
the test leads across the break and apply
power.
5. Read the measured current on the display.
Measure Resistance
1. Connect the black test lead to the COM
Terminal and the test lead to the VΩHz
Terminal.
2. Turn the rotary switch to ,and the display
will show “ ”.
3. Touch the probes to the desired test points of
the circuit to measure the resistance.
4. Read the measured resistance on the display.
11
*Do not measure current that exceeds the extremes
as indicated in the Specifications.
*Use the A mA Terminal and the Mode when
you are measuring an unknown current. Then
switch to the VΩHz Terminal and the Mode if
necessary.
*Do not input voltage at this setting.
2. Turn the rotary switch to or .
3. Press SEL to toggle between AC/DC.
4. Break the circuit path to be measured, connect
the test leads across the break and apply
power.
5. Read the measured current on the display.
Measure Resistance
1. Connect the black test lead to the COM
Terminal and the test lead to the VΩHz
Terminal.
2. Turn the rotary switch to ,and the display
will show “ ”.
3. Touch the probes to the desired test points of
the circuit to measure the resistance.
4. Read the measured resistance on the display.
11
*Do not measure current that exceeds the extremes
as indicated in the Specifications.
*Use the A mA Terminal and the Mode when
you are measuring an unknown current. Then
switch to the VΩHz Terminal and the Mode if
necessary.
*Do not input voltage at this setting.
copyrighted document - all rights reserved by FBC
