MyBinding Standard PC II- Bedienungsanleitung
Instruction Manual
Provided By
http://www.MyBinding.com
http://www.MyBindingBlog.com
Standard PC-64 II
Paper Cutter
I
UM204006-04
090617/PC64II/04E/DV
Important Information
- This manual is designed to help you to install, operate and maintain Paper Cutter, PC-
64II. Read, understand and keep this manual in a safe and convenient place.
- Do not operate PC-64II until you read and understand the instructions in this manual.
- Horizon International Inc. shall not be liable for incidental consequential damages result-
ing from : improper or inadequate maintenance by customer; unauthorized modification or
misuse; operation outside of the environmental specifications for the product.
- Horizon International Inc. pursues a policy of continuing improvement in design and
performance of the product. Therefore, the product design and specifications are subject to
change without prior notice and without our legal obligation.
- All rights are reserved. No part of the manual may be photocopied, reproduced or trans-
lated to another language without the prior written consent of Horizon International Inc.
PC-64II
PAPER CUTTER
2
3
Knife Lamp
Left Small Cover
5
IMPORTANT:
- Knife will come to a stop instantly when
one or both buttons are released before knife
reaches its lowest point. To reverse move-
ment of knife depress cut buttons A & B
separately with the interval of 0.5 seconds or
more. Knife will reverse direction. Hold cut
button until knife stops at home position
(upper position).
- If knife is past it's lowest position it should
return automatically to home position even if
cut buttons are released.
6. Cut cycle complete.
- Ensure knife stops at home position (upper
position).
- Turn off power switch.
- Remove trimmings. (Fig. 2-4)
- Turn paper clamp hand wheel (Fig. 2-4)
counterclockwise until paper lift is released.
- Remove lift of paper.
7. Job complete.
- Turn key switch off and remove key. (Fig.
2-4)
- Unplug power cord.
IMPORTANT:
Keep key switch at safe place by an authorized
operator.
5
ADDITIONAL INFORMATION
- If the front cover is opened while the knife
is moving, the buzzer beeps and the knife
lamp lights.
In this case, follow the steps below to move
the knife to the home position.
1. Close the front cover.
- In case that the knife stops during raising because
the front cover is opened, the knife returns to the
home position automatically after closing the cover.
If the knife still stay there, go to the next step.
2. Press the cut button A first, and then press the cut
button B after 0.5 seconds or more.
- The knife returns to the home position automati-
cally.
f
5
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere MyBinding Cutter Handbücher
MyBinding
MyBinding IDEAL 4850-95 EP Bedienungsanleitung
MyBinding
MyBinding Swingline ClassicCut Ingento Bedienungsanleitung
MyBinding
MyBinding DC-545HC Bedienungsanleitung
MyBinding
MyBinding IDEAL 5221-95EP Bedienungsanleitung
MyBinding
MyBinding Standard APC45 Programmable Bedienungsanleitung
MyBinding
MyBinding MBM BC12 Bedienungsanleitung
Beliebte Cutter Handbücher anderer Marken
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung
Makita
Makita DCS552 Bedienungsanleitung
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Bedienungsanleitung
Makita
Makita 4112HS Bedienungsanleitung
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Bedienungsanleitung
Hitachi
Hitachi CM 4SB2 Fehlerbehebungshandbuch
