MyBinding Formax FD-346 Bedienungsanleitung

Formax FD-346 Paper

Folder with Touch Screen

Instruction Manual

FD 346 / FE 346

Document Folder

FI / FJ Series

OPERATOR MANUAL

FIRST EDITION

3/2018

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

TABLE OF CONTENTS

SUBJECT PAGE

DESCRIPTION 1

SPECIFICATIONS 1

UNPACKING 2

SETUP 2

CONTROL PANEL 3

OPERATION 4

SETTING CUSTOM FOLDS 5

AUTOBATCH MODE 5

MULTI-SHEET FEEDING (OPTIONAL) 6

CROSS FOLDING 7

STACKER WHEEL POSITIONING CHART 7

STACKER WHEEL SETUP FOR THICK PAPER 8

REMOVING OUTFEED COVER 8

REMOVING INFEED TIRES 9

OPERATOR MAINTENANCE 9

ERROR SCREENS 10

TROUBLE-SHOOTING 11

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

DESCRIPTION

Upper Fold Table

Telescoping

Outfeed Stacker

Self Centering Paper

Side Guides

Infeed Tray

Extension

Infeed Tray

Lever

Lower Fold

Table

Non-Operator Side

Operator Side

FUNCTION

This document folder is designed to perform a wide variety of folds using a variety of paper weights. The fold plates are

manually adjusted for standard folds and custom folds. Batch counting, self-centering side guides, and the capability to

cross-fold are added features. The folder will automatically stop after the last document has been folded.

SPECIFICATIONS

Speed: Standard Mode: Up to 15,500/hour, depending on fold type

Hopper Capacity: Up to 500 sheets of 20# paper (75gsm)

Paper size: Min: 3.5” X 5” (88.9 W x 127 L mm)

Max: 12.25” X 18” (311 W x 457 L mm)

Pre-Marked fold types: Letter , Zig-Zag , Single , Gate , Fold Out ,

Double Parallel

Pre-Marked Paper Sizes: FD Model: 11”, 14”, 17”

FE Model: A5, A4, A3, B6, B5, B4

Weight: 67 lbs (30 kg)

Power: FD Model: 120 volts A.C., 50/60 Hz, 2 amps.

FE Model: 220 volts A.C., 50/60 Hz, 2 amps

Safety Certications: UL, CUL, & CE Approved

Control Panel

Power Inlet & Circuit breaker

Power Switch

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Fig. 1b Locating Pins

Lower Fold Table Pins

Fig. 1a Locating Pins

Upper Fold Table Pins

UNPACKING & SETUP

1. Check package for shipping damage. If there is shipping damage, do not discard the box.

2. Remove the machine and packed components from the box. The fold plates, telescoping stacker, Optional Multi

Sheet Feeder if ordered, power cord and cross-fold guide are wrapped separately in the box.

NOTE: Two people must lift the machine from the box.

3. Place the folder on a solid wooden or metal stand.

Install upper and lower fold plates, telescoping conveyor

multi-sheet feeder and power cord

1. Be sure the plates are set rmly on the locating pins

(Fig 1a & 1b). Slide each fold plate in until it meets the

rst locating pin then push down to set in place.

2. Repeat the same steps for the lower fold plate.

3. Insert the telescoping extension tray into the end of the

outfeed conveyor (Fig. 2).

Fig. 2 Telescoping extension tray

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

4. If equipped, insert the optional Multi-Sheet Feeder into

the four slots located on the top cover (Fig 3).

Note: Technical assistance is required to install the multi-

sheet feeder components if it is purchased separetly

from the folder.

5. Make sure the power switch is in the “OFF” position.

Plug the power cord into the power inlet and the wall

outlet.

Fig. 3

4 Slots

No. NAME FUNCTION

1 Counter Display 6-digit resettable counter

2 Counter Reset Icon Resets the counter to “000000”

3 Start Icon Press to start the Folder

4 “1X” Icon Test folds one document

5 AutoBatch Mode Icon Press to enter the Batch mode

6 Stop Icon Press to stop the folder

7 AutoBatch Mode:

Number Folded Sets

Press to enter the number of batched sets (up to 999 sets)

8 AutoBatch Mode:

Number of documents

Press to enter the number of documents in a batched set (up to 999 documents)

9 AutoBatch Mode:

Delay between sets

Press to enter the time delay between each set (up to 99 seconds)

10 Home Icon Press to return to the main screen

CONTROL PANEL

Main Screen: AutoBatch Mode Screen:

4 4 10

OPERATION

1. Place power switch in the “ON” position.

2. To set the fold plate stop position, squeeze the

stop plate lever and move the stop plate to the

desired location on the upper and lower fold plates

(Fig 4). Align the pointed part of the stop plate with

the desired marks on the decal and release the lever.

Fine adjustments can be made with the adjustment

knob at the end of the plate (Fig 5).

NOTE: When doing a “Single” fold, be sure to move

the lower fold plate stop all the way to the front of

the plate. The plate must be rmly reinstalled on the

locating pins.

3. Move the stacker wheels to the proper position for

the paper size (Fig 6) ( Refer to chart on page 7).

4. Extend the telescoping conveyor stacker as required.

5. Lift the in-feed tray extension into position.

6. Raise the in-feed tray lever.

7. Set the paper side guides for the paper you’re using

and lock in position.

8. Neatly stack paper on the in-feed tray.

9. Lower the in-feed tray lever.

10. Press the “ ” icon on the control panel to check

the folds. Adjust as needed.

11. If the fold is skewed use the skew adjustment knob

to make corrections (Fig.7).

12. When you’re satised with the test folds, press the

“ ” icon to operate the machine.

Fig.7

Fig. 6

Fig. 5

Stacker Wheels

Stacker Wheel Positions A, B & C

Skew Adjuster

Fig. 4

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

SETTING CUSTOM FOLDS

AUTOBATCH COUNTING MODE

The AutoBatch feature can be set to count down the number of

sets in a batch, the number of sheets in each set, and the delay

between each set. To enter the AutoBatch Mode press the

“ “ icon on the main screen.

To enter the number of sets press the “ “ (g. 8a). Enter

the number of sets on the keypad that appears. Next press the

“ “ icon to select the number of sheets, and then press the

“ “ icon to enter the delay between sets. Press the “ “ to

exit the keypad.

Press the “ “ icon to begin folding. The folder will stop

when the number of sets counts down to zero (0).

To exit the AutoBatch Mode press the “ “ icon.

Note: Press the “ “ icon on the keypad to exit back to the

Auto Batch screen. Press the “ “ icon to edit the number

entered. Press the “ “ icon on the keypad to reset the

entered number to zero (0).

Example 1: Uneven “Z”

1. Measure the length of panel “A”

2. Adjust the upper fold plate so that the stop plate lines

up with the measurements of the panel “A” i.e. if panel

“A” is 5 1/4” long slide the stop plate up or down so that

it lines up with the 5 1/4” mark on the fold plate.

3. Measure the length of panel “B”

4. Adjust the lower fold plate so that the stop plate lines

up with the measurement of panel “B”

5. Load forms and press test. If folds are too long or too

short adjust accordingly.

1. Measure the length of panel “A” & “B”

2. Adjust the upper fold plate so that the stop plate lines up

with the measurements of panel “A” & “B”. i.e. if panel

“A” & “B” are 10 1/2” long slide the stop plate up or

down so that it lines up with the 10 1/2” mark on the fold

plate.

3. Measure the length of panel “B”

4. Adjust the lower fold plate so that the stop plate lines up

with the measurement of panel “B

5. Load forms and press test. If folds are too long or too

short adjust accordingly.

Example 2: Uneven “C”

Panel A

Panel B

Panel A

Panel B

Fig. 8a

Fig. 8b

1 2

MULTI-SHEET FEEDING (OPTIONAL)

The multi-sheet feeder is designed to fold pre-collated stapled or unstapled sets of up to four 20 # (75gsm)sheets of

paper. NOTE: This feature will not work in AutoBatch mode. The home screen must be displayed in order for the multi-

sheet feeder to work properly.

1. Adjust the side guides on the multi-sheet feeder for the

proper paper size. Loosen the thumb screw, adjust the

guides to t the paper width and re-tighten the thumb-

screw (Fig 9a).

2. Slide the pre-collated paper set into the multi-sheet

feeder. When feeding stapled sets the documents

should be placed with the staple on the operator’s side

and leading (Fig 9b).

3. The sheets of paper will be automatically pulled into the

folder.

4. If the fold is skewed, turn the skew adjustment knob

located on the back of the feeder left or right to make

corrections (Fig 9c).

5. To remove the multi-sheet feeder depress the release

levers located on either side of the lower back side of

the feeder (Fig. 9d), tilt the feeder forward and lift. To

reinstall depress the levers and reinsert.

Staple

Fig. 9b

Fig. 9a

Fig 9c

Brass thumbscrew

Skew Adjuster

Release Levers

Fig. 9d

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

CROSS FOLDING

Cross folding refers to folding a document in one pass and

then running it through the folder a second time to be folded

again.

Common Application: Folding a 11” x 17” document in half

and then letter folding it to t in a standard #10 envelope.

1. Load folded paper into the feed tray with the fold

crease facing the non-operator side of the folder

(Fig 10a).

Note: For best results, rmly run your hand over the

fold crease to help atten the paper before loading.

2. Attach the cross fold paper guide onto the feed tray

paper guide (Fig. 10b) and lower guide.

Note: Cross folding ability will vary based on the paper

weight and type. If the paper is too heavy it may not

be able to be cross folded.

Note: The guide can be conveniently stored under the

lower fold table when not in use (Fig 10c).

Tab “B” Tab “A”

Slot “B” Slot “A”

Fig. 10b

To install cross fold guide hook tab “A” into slot “A” and

then lower tab “B” into slot “B”

Fig. 10a

Fold Crease Cross Fold Guide

STACKER WHEEL POSITIONING GUIDE

8.5" x 11" 8.5" x 14" 11" x 17"

Letter

Zig-Zag

Single

Gate

Fold Out

Double ll

A or B

Move the stacker wheels to the proper position indicated on the chart based on the fold and paper size (Fig 11a and 11b).

Stacker Wheels

Fig. 11b

Fig. 11a

Stacker wheels decal

Fig. 10c Cross fold guide storage

Inhaltsverzeichnis

Andere MyBinding Papierfaltmaschine Handbücher

MyBinding

MyBinding Martin Yale 2051 Bedienungsanleitung

Beliebte Papierfaltmaschine Handbücher anderer Marken

KRUG+PRIESTER

KRUG+PRIESTER IDEAL 8570 Bedienungsanleitung

Pressure Seal Systems

Pressure Seal Systems PS300 Bedienungsanleitung

Olympia

Olympia FM 4420 Bedienungsanleitung

Horizon Fitness

Horizon Fitness QC-S30 Betriebsanleitung

Cyklos

Cyklos CFM 600 Bedienungsanleitung

Dynafold

Dynafold Paper Folder PF-330 Bedienungsanleitung

Cyklos

Cyklos GPM 450 Bedienungsanleitung

Challenge

Challenge MEDALIST 820 Technisches Referenzhandbuch

Martin Yale

Martin Yale 1611 Bedienungsanleitung

Martin Yale

Martin Yale 1701 Bedienungsanleitung

Duplo

Duplo DBM-120 Bedienungsanleitung

FP Mailing Solutions

FP Mailing Solutions FPi 2300 Bedienungsanleitung

Duplo

Duplo DF-520 Bedienungsanleitung

FP FPi2000 Bedienungsanleitung

Westfalia

Westfalia 56 56 22 Bedienungsanleitung

MBM

MBM 1800S Bedienungsanleitung

PaperFolder

PaperFolder PF-PH-1 Bedienungsanleitung

Standard

Standard PF-P310 Bedienungsanleitung